Parts for Maytag MLE20PDBGW2: 10 - Dispenser Parts

This replacement screw secures panels and internal components in your appliance. It restores a tight, reliable hold when the original fastener is missing, stripped, or corroded—helping keep assemblies aligned and reducing vibration or rattling.

• Fastens panels, brackets, and components to the cabinet or frame
• Helps maintain alignment and reduce rattling or buzzing noises
• Replaces damaged, rusted, or missing fasteners
• Typical signs: loose covers/panels, gaps or misalignment, vibration during operation

• Disconnect power before servicing; wear work gloves
• Match thread and length to your model's parts diagram before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If replacing multiple screws, swap one at a time to maintain alignment

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

This drain hose carries used water from the appliance to the household drain. A secure, leak-free drain path helps prevent water from backing up or leaking during and after a cycle.

• Routes wastewater from the unit to the standpipe or sink drain
• Helps resolve issues like slow or incomplete draining
• Can address leaks found around the rear or drain area
• Restores proper water exit flow after hose damage or kinks

• Unplug power and shut off water before servicing
• Have a towel or shallow pan ready to catch residual water
• Note hose routing and connections before removal; transfer any clamps if reused
• Ensure tight, watertight connections and proper routing without kinks

Restore the clean look and proper function of your washer's detergent compartment with this detergent dispenser drawer cover. It replaces a cracked or missing cover so the drawer closes correctly and helps reduce splashing at the dispenser. What it does:

• Covers and protects the front of the detergent dispenser drawer
• Helps the drawer align and close properly for consistent dispensing
• Replaces broken or missing cover tabs that prevent the drawer from staying in place
• Common symptoms: cracked/missing cover, broken tabs, drawer won't close or feels loose, splashing/leaks at the dispenser area

• 1 detergent dispenser drawer cover

• Unplug the appliance and shut off water supply before servicing
• Pull the dispenser drawer out and depress the release tab to remove it
• Release the locking tabs to remove the old cover; snap the new cover fully into place
• Reinstall the drawer and run a quick test to check operation

The Retainer is an OEM part for Whirlpool washing machines. It is designed to hold various components in place within the washing machine, ensuring they remain securely attached during operation. 

You should replace the retainer if it becomes damaged or worn out. Causes of a bad retainer can include regular wear and tear, physical damage from impacts, or degradation from constant use. A compromised retainer can lead to components becoming loose, which may cause noise, inefficiency, or further damage to the washing machine.

Symptoms of a bad retainer include:

• Loose or misaligned internal components
• Unusual noises during the wash or spin cycles
• Components shifting or falling out of place
• The washing machine vibrating excessively or not operating smoothly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models. 

This replacement commercial door restores a secure, smooth-closing entry to your appliance. Use it to replace a cracked, bent, or damaged door to maintain proper closure, alignment, and appearance so the unit functions as intended.

• Functions as the appliance's front door, providing access for loading/unloading
• Interfaces with hinges and latch/strike for smooth operation and secure closure
• Presents the proper contact surface for the seal or interlock area, where applicable
• Typical symptoms: door cracked, warped, or loose; won't close or latch; misaligned or rubbing

• Disconnect power; if the unit connects to gas or water, shut those off before service
• Support the door while removing hinge and latch/strike fasteners to avoid cabinet damage
• Transfer any reusable hardware, trim, or nameplates from the old door to the new one
• After installation, verify alignment and latch engagement; adjust hinges/strike for an even seal

The Dispenser Hose is an OEM replacement part for Whirlpool washing machines. This hose is integral in the detergent dispensing system, channeling liquid detergent and other washing agents from the dispenser to the wash drum. It ensures that cleaning agents are efficiently delivered to the laundry load at the appropriate time during the wash cycle.

Symptoms of a bad Dispenser Hose include:

• Leakage of detergent or water from the dispenser
• Detergent not being dispensed into the wash drum
• Residual detergent left in the dispenser after the wash cycle
• Unusual sounds, like gurgling or splashing, during detergent dispensing

Causes for a malfunctioning Dispenser Hose can include blockages from accumulated detergent residue, cracks or holes in the hose, or issues with the connectors that attach it to the dispenser and drum.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a genuine replacement handle that restores a secure, comfortable grip for opening and closing your appliance. Use it to replace a cracked, broken, or missing handle and bring back a clean, factory look and feel. What it does

• Provides a sturdy grip to operate the appliance door or drawer
• Restores proper fit and alignment with existing mounting points
• Improves usability when the original handle is loose or damaged
• Common symptoms: cracked or broken handle, looseness, missing handle, cosmetic wear

• One handle

• Disconnect power to the appliance before beginning work
• Remove the fasteners from the old handle and transfer any reusable hardware
• Align the new handle with the mounting points; start all screws by hand to avoid cross-threading
• Tighten evenly without over-torquing; test operation after installation

This dispenser handle cover attaches to the front of the dispenser assembly, providing the finished surface you press or pull and protecting internal components. Replacing a cracked or missing cover restores clean appearance and reliable, comfortable operation.

• Provides the user-facing surface for operating the dispenser
• Covers and helps protect the internal lever/switch area
• Restores proper feel and alignment of the actuator
• Common symptoms: cracked/broken cover, loose or missing handle, sticking or hard-to-use dispenser, cosmetic wear

• Disconnect power to the appliance; shut off water supply if working near water connections
• Access the dispenser area; release retaining tabs or screws and carefully remove the old cover
• Align the new cover and snap or fasten it into place without overflexing the tabs
• The actuator/drawer moves freely before restoring power