Parts for Maytag MLE20PRBZW2: 10 - Dispenser Parts

The Valve is an OEM part for Whirlpool washing machines. This water inlet valve controls the flow of water into the washing machine, ensuring the proper amount of water is used for each wash cycle. It plays a crucial role in the washing process by regulating the water intake from your home's plumbing.

Over time, the valve can wear out or become clogged with sediment and mineral deposits, leading to issues with water flow. Electrical malfunctions or mechanical failures can also impair the valve's functionality.

Symptoms of a bad valve include:

• The washing machine not filling with water
• Slow filling or no water flow
• Leaking water when the machine is off
• Error codes related to water supply issues
• Unusual noises during the water filling cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Valve is an OEM replacement part for Whirlpool washing machines. This valve is responsible for controlling the flow of water into the washing machine during various cycles and operations.

Causes of a bad valve can include mineral or sediment buildup restricting water flow, worn seals or diaphragms allowing leaks, or mechanical failure of internal components.

Symptoms of a bad valve include:

• Inability to fill or drain the washing machine properly
• Excessive water usage or leaks
• Abnormal sounds during filling or draining cycles
• Incomplete or ineffective wash cycles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

This drain hose carries used water from the appliance to the household drain. A secure, leak-free drain path helps prevent water from backing up or leaking during and after a cycle.

• Routes wastewater from the unit to the standpipe or sink drain
• Helps resolve issues like slow or incomplete draining
• Can address leaks found around the rear or drain area
• Restores proper water exit flow after hose damage or kinks

• Unplug power and shut off water before servicing
• Have a towel or shallow pan ready to catch residual water
• Note hose routing and connections before removal; transfer any clamps if reused
• Ensure tight, watertight connections and proper routing without kinks

Restore the clean look and proper function of your washer's detergent compartment with this detergent dispenser drawer cover. It replaces a cracked or missing cover so the drawer closes correctly and helps reduce splashing at the dispenser. What it does:

• Covers and protects the front of the detergent dispenser drawer
• Helps the drawer align and close properly for consistent dispensing
• Replaces broken or missing cover tabs that prevent the drawer from staying in place
• Common symptoms: cracked/missing cover, broken tabs, drawer won't close or feels loose, splashing/leaks at the dispenser area

• 1 detergent dispenser drawer cover

• Unplug the appliance and shut off water supply before servicing
• Pull the dispenser drawer out and depress the release tab to remove it
• Release the locking tabs to remove the old cover; snap the new cover fully into place
• Reinstall the drawer and run a quick test to check operation

The Retainer is an OEM part for Whirlpool washing machines. It is designed to hold various components in place within the washing machine, ensuring they remain securely attached during operation. 

You should replace the retainer if it becomes damaged or worn out. Causes of a bad retainer can include regular wear and tear, physical damage from impacts, or degradation from constant use. A compromised retainer can lead to components becoming loose, which may cause noise, inefficiency, or further damage to the washing machine.

Symptoms of a bad retainer include:

• Loose or misaligned internal components
• Unusual noises during the wash or spin cycles
• Components shifting or falling out of place
• The washing machine vibrating excessively or not operating smoothly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models. 

This replacement commercial door restores a secure, smooth-closing entry to your appliance. Use it to replace a cracked, bent, or damaged door to maintain proper closure, alignment, and appearance so the unit functions as intended.

• Functions as the appliance's front door, providing access for loading/unloading
• Interfaces with hinges and latch/strike for smooth operation and secure closure
• Presents the proper contact surface for the seal or interlock area, where applicable
• Typical symptoms: door cracked, warped, or loose; won't close or latch; misaligned or rubbing

• Disconnect power; if the unit connects to gas or water, shut those off before service
• Support the door while removing hinge and latch/strike fasteners to avoid cabinet damage
• Transfer any reusable hardware, trim, or nameplates from the old door to the new one
• After installation, verify alignment and latch engagement; adjust hinges/strike for an even seal

This clamp secures flexible hoses and small-diameter tubing to fittings, helping prevent leaks and maintain proper fluid flow in appliance systems. It's a simple replacement that restores a tight, reliable connection. What it does

• Holds a hose or tube firmly on a barb or nipple to stop leaks and loss of pressure
• Keeps water, drain, or vent hoses seated during normal appliance operation
• Replaces worn, corroded, or loose clamps that cause dripping or poor connections
• Works where a small, durable clamp is required for routing or securing tubing

• One hose clamp

• Inspect hose and fitting for damage; replace hose if cracked or hardened before installing the clamp
• Tighten clamp until snug—do not overtighten; ensure even compression around the hose
• Disconnect power and water as appropriate and take safety precautions before working on the appliance

The Dispenser Hose is an OEM replacement part for Whirlpool washing machines. This hose is integral in the detergent dispensing system, channeling liquid detergent and other washing agents from the dispenser to the wash drum. It ensures that cleaning agents are efficiently delivered to the laundry load at the appropriate time during the wash cycle.

Symptoms of a bad Dispenser Hose include:

• Leakage of detergent or water from the dispenser
• Detergent not being dispensed into the wash drum
• Residual detergent left in the dispenser after the wash cycle
• Unusual sounds, like gurgling or splashing, during detergent dispensing

Causes for a malfunctioning Dispenser Hose can include blockages from accumulated detergent residue, cracks or holes in the hose, or issues with the connectors that attach it to the dispenser and drum.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a genuine replacement handle that restores a secure, comfortable grip for opening and closing your appliance. Use it to replace a cracked, broken, or missing handle and bring back a clean, factory look and feel. What it does

• Provides a sturdy grip to operate the appliance door or drawer
• Restores proper fit and alignment with existing mounting points
• Improves usability when the original handle is loose or damaged
• Common symptoms: cracked or broken handle, looseness, missing handle, cosmetic wear

• One handle

• Disconnect power to the appliance before beginning work
• Remove the fasteners from the old handle and transfer any reusable hardware
• Align the new handle with the mounting points; start all screws by hand to avoid cross-threading
• Tighten evenly without over-torquing; test operation after installation

This dispenser handle cover attaches to the front of the dispenser assembly, providing the finished surface you press or pull and protecting internal components. Replacing a cracked or missing cover restores clean appearance and reliable, comfortable operation.

• Provides the user-facing surface for operating the dispenser
• Covers and helps protect the internal lever/switch area
• Restores proper feel and alignment of the actuator
• Common symptoms: cracked/broken cover, loose or missing handle, sticking or hard-to-use dispenser, cosmetic wear

• Disconnect power to the appliance; shut off water supply if working near water connections
• Access the dispenser area; release retaining tabs or screws and carefully remove the old cover
• Align the new cover and snap or fasten it into place without overflexing the tabs
• The actuator/drawer moves freely before restoring power

This replacement screw secures panels and internal components in your appliance. It restores a tight, reliable hold when the original fastener is missing, stripped, or corroded—helping keep assemblies aligned and reducing vibration or rattling.

• Fastens panels, brackets, and components to the cabinet or frame
• Helps maintain alignment and reduce rattling or buzzing noises
• Replaces damaged, rusted, or missing fasteners
• Typical signs: loose covers/panels, gaps or misalignment, vibration during operation

• Disconnect power before servicing; wear work gloves
• Match thread and length to your model's parts diagram before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If replacing multiple screws, swap one at a time to maintain alignment