Dixon Lawn Mower Parts

Flat idler pulley for riding mowers and lawn tractors. Works with the belt to transfer power from engine to drive system. Replace if cracked or worn.

Deck spindle assembly for riding mowers and lawn tractors. Mounts under the mower deck to hold and spin cutting blades. Replace if cracked, bent, or worn.

Flanged hex nut for lawn tractors and outdoor power equipment. Replace if threads are stripped, nut is missing, or hardware has corroded or loosened.

Replacement deck belt for riding mowers. Connects rotating shafts to ensure smooth cutting performance. Replace if worn, cracked, or slipping. Verify fit with your model number before ordering.

Mower won't start or starter doesn't engage? This ignition switch activates your riding mower's electrical system. Simple DIY repair in under 30 minutes.

Twin-muffler assembly for riding mowers with two-cylinder engines. Connects to exhaust pipes to reduce noise and emissions. Replace if cracked or damaged.

Steering shaft connects the steering wheel to the gearbox on riding mowers and lawn tractors. Replace if bent, cracked, or worn for proper steering control.

This part is a clutch that is used on lawn tractors and riding lawnmowers. A clutch transfers the power from the unit's engine to the drivetrain and is responsible for engaging the blade.A new clutch may be needed if the lawn tractor or riding lawn mower will start but then stalls. If the clutch is sticky or if it operates hard, it may be time to replace the clutch. If the engine is revving higher than usual or if there are strange noises coming from the clutch, it is likely that the clutch could be going bad. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This clutch is a genuine Husqvarna part. It is sold individually. This particular clutch is compatible with lawn tractors and riding lawnmowers that are manufactured by Husqvarna and Poulan.

Protects wheel hub and lug nuts from dirt and grime on riding mowers and tractors. Simple snap-on installation takes minutes with basic tools.

Can't see while mowing at dusk or dawn? This riding mower headlight switch controls your tractor's illumination system. Direct-fit replacement.

Mandrel spacer washer for riding mowers and lawn tractors. Installs between drive pulleys to maintain proper alignment and spacing. Replace if worn or missing.

Hardened washer for lawn tractors and riding mowers. Installs with bolts to redistribute pressure and prevent loosening. Replace if worn or missing.

Secures the mower blade to the spindle on riding mowers and tractors. Replace if bolt is stripped, washer is damaged, or hardware is missing.

Idler pulley for riding mowers and tractors. Maintains proper belt tension for drive system. Replace if pulley is cracked, worn, or spinning rough.

This idler arm is a genuine Husqvarna part, sold individually. This idler arm can be used as a replacement part in a lawnmower. This part secures the steering linkage while allowing it free range of motion. If the idler arm is punctured, dented, cracked, chipped, scraped, warped, or eroded, it should be removed and replaced by this genuine OEM replacement part as soon as possible in order to ensure safe continued use.This is a genuine OEM replacement directly from the manufacturer. It is sold individually. This idler arm is compatible with the following outdoor appliance brands: Husqvarna.

This 16.25 inch-long blade is manufactured for use with lawn mowers, lawn tractors, zero-turn mowers, and riding mowers. It is a genuine Husqvarna part. The blade is a crucial component of the mower. It is the part that actually cuts grass. It is normal for the blade to become dull over time. They can be sharpened, but replacing will yield better results.Before replacing the blade on a mower, allow the engine to cool, empty the fuel tank, and disconnect the spark plug for safety. Wear work gloves to protect the hands. Tip the lawnmower onto its handle assembly or side. Use a socket to remove the nuts or bolts that attach the blade to the mower. Replace with the new blade and torque the nuts and bolts.This blade is a genuine OEM part sourced directly from the manufacturer. It is sold individually, and most mowers have only one cutting blade. It is manufactured to be compatible with several models made by Dixon, Husqvarna, and Jonsered.