David S Palm Harbor , FL September 24, 2016 Appliance: Model FTQ3531WUX/XAA Missing segments in display oven not holding temperature setting burner always on high After removing the top rear access panel, I took as-built photographs of the two components to be replaced showing all wires, connectors and screws! The Energy Regulator for the front left burner was replaced first, noting the orientation before pulling off the knob, and removing the retaining screws. I used long nose pliers to gently remove one lead at a time and reconnect to the new regulator. Checked orientation against the photo, reinstalled regulator and knob. Main PCB Assembly was more challenging. The assembly snaps into a plastic holder / frame that is held in place by 3 or 4 corner screws and two screws on the controller board transformer. After removing the screws, the frame and PCB Assembly can be removed giving access for removal of the connectors. The connectors have various "latches" that need to be released to remove the connectors without damage. Some tenacity is needed here, especially for the removal and re-installation of the flex tape cable on the left side of the PCB Assembly. The flex cable is released by pulling up on the "collar" of the black plastic latch to release the flat cable. For reassembly, the "collar" must be pulled up to allow the flex tape cable to be fully inserted in the connector slot, after which the "collar" is pressed down to re-establish connector contacts. The flex tape cable is very delicate and must be handled carefully to avoid damage. If it is not inserted correctly, the membrane keypad on the stove will not work. After all connectors / cables have been removed, release the PCB Assembly from the holder / frame, and install the new PCB into the holder / frame. Reinstall the PCB Assembly and the holder / frame and replace the corner screws and the two screws on the controller board transformer. Reconnect all cables, using the photographs as needed and paying careful attention to the flex cable as previously mentioned. Replace top rear access panel. Read More... 28 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Pliers, Screwdrivers
Robert L Lake Charles , LA December 16, 2016 Appliance: Model FTQ3531WUX The clock/cooking temp face was unreadable I replaced the Pcb Main Assy, in other words, the computer board that houses the clock face and cooking temp face. It really is an easy fix for those who have any mechanical abilities. Mention was made by another about the "flex cable" on the left of the board. NOTICE, the little black keeper does not completely remove, it only slides up just a touch and then the "flex cable" can be gently pulled from the connector. The only other connections that gave me a puzzle for a moment was the 2 "metal" connectors on the bottom left of the board. They have a tiny "release" within the clip, under the plastic hood, that must be pressed in order for the clip to release from the lug. Other than that, anyone with reasonable skill should be able to do this themselves. Read More... 7 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Mary B Wheeling , WV December 12, 2016 Appliance: Model SAMSUNG Missing display segments As in any repair <<< disconnect the power cord supply from the wall plug completely >>>> Removed the cover screws on rear top panel, At this point examine the Board to be Installed and confirm the part id numbers match to insure you have the exact replacement board you need ...... Carefully disconnect all the plug in connectors - be careful to mark the original positions for re install... note there is one ribbon cable on left side that connects differently - open latch and pull out the ribbon - reverse install... make positive it is completely inserted all the way on re install . Note there is (2) screws on the transformer that needs to be removed prior to flexing control board loose from its hooks... Replaced the control board and display worked fine. Read More... 4 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Pliers, Screwdrivers
William H Winterville , NC December 18, 2016 Appliance: Samsung Range FTQ353IWUX/XAA-0000 Digital display missing charcters couldn't tell the correct time or oven temperature Replaced Pcb Main Assy card. First card sent didn't have a display at all so I called customer service and they sent another card and it works great. Read More... 2 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Pliers, Screwdrivers
Mark D Holden , MA May 20, 2016 Appliance: Samsung Range FTQ353IWUX/XAA-0000 A relay or 2 on the pcb main assembly crashed and burned Samsung sent someone for free to diagnose. We were hoping they'd cover the repair. The technician called back with a quote of $500 to replace board and wiring harness. AppliancePartsPros had the board for approx $115 and I was able to replace the melted connector on the wiring harness for $2. Many years ago I was an Aviation Electrician's Mate in the Navy, so I was on somewhat familiar ground. Read More... 2 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Pliers, Screwdrivers
Albert C Cape Coral , FL March 04, 2017 Display not working properly Changed the whole board and overlay Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Pliers, Screwdrivers
Wayne S Stevens Point , WI February 21, 2016 Missing characters in the display and segments lit when they were not supposed to be lit Replaced the main PC board. Also replaced the membrane keypad - just in case that was a problem; but I think the original was okay. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Screwdrivers
Kenneth C Columbia , SC May 16, 2020 Appliance: Samsung Range FTQ353IWUX/XAA-0000 Burner stayed on when it should be cycling off and missing segments on the display. I had missing segments on the LCD clock display, it was a annoyance but otherwise the stove worked fine. Recently I noticed that my front right burner was getting my food way to hot even when it was set to low. At first I wasn't sure what was happening because it did not do it all the time. It turned out that these Samsung stoves have this problem when the switch that your knob is connected to goes bad. The element would come on and stay on, if your stove starts to act this way you should stop using that burner until you can replace the switch. Be sure to take pictures of the wiring so you won't have any problems hooking the connectors back up. There are several videos on the internet you can watch so that you will help you understand how to disconnect the ribbon cable and other connectors. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Pliers, Screwdrivers
Steve W Panama City , FL January 07, 2020 Appliance: Model FTQ3531WUW Many of the digits and characters were not displayed on the display board. the right double range top element went to full power whenever turned on regardless of setting Replaced the pcb main assembly board and the right infinity energy regulator (burner control switch). Read More... Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Pliers, Screwdrivers
Gregory R Dawsonville , GA July 22, 2019 Digits missing on clock display Installed new PCB main assembly Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Screwdrivers