Parts for Frigidaire CFGS365EB2: 11 - Door Parts

Trim panel for wall ovens and ranges. Covers gaps between stacked units or cabinet openings. Replace if cracked, broken, or missing during installation.

Replace cracked, shattered, or broken outer door glass on your oven. Restores the appearance and integrity of your oven door after damage or wear.

Oven won't maintain temperature or exterior gets too hot? This insulation blanket contains heat and protects nearby components. Moderate DIY repair.

Heat-resistant insulation that wraps the oven cavity to contain heat. Replace if worn, damaged, or missing to improve heat retention and efficiency.

Inner door glass panel for range and wall oven doors. Replace if cracked, shattered, or slipped out of position. Installs between outer glass and oven cavity.

Replacement mounting screw for ovens, ranges, and wall ovens. Secures panels, handles, brackets, and internal components when original hardware is stripped, missing, or damaged.

Seals oven door to prevent heat loss and improve efficiency. Replace if frayed, damaged, or door doesn't close properly. Verify fit with your model number.

Mounting screw for electric range, oven, or wall oven assembly. Secures internal components and panels. Replace if stripped, missing, or damaged.

Spacer that maintains proper gap between components in your range or oven assembly. Replace if missing, worn, or damaged to restore correct fit and alignment.

Protective shield that covers and guards the switch assembly on your range. Replace if the original shield is cracked, broken, or missing to restore proper coverage.

This wiring diagram is the replacement schematic label that shows the appliance's electrical circuits and connector locations for service reference. It helps technicians and owners read wire colors, terminal IDs, and routing to diagnose electrical issues. What it does:

• Provides the factory wiring schematic and terminal/key legends for accurate troubleshooting
• Helps identify wire colors, connector positions, and component interconnections
• Useful when the original label is missing, faded, or damaged and circuit information is unreadable
• Assists in verifying proper wiring during repairs or after component replacement

• Disconnect power to the appliance before accessing the area where the label mounts
• Replace only on the documented mounting surface; clean and dry surface for adhesive labels
• Handle carefully to avoid creasing or smudging printed information

This is a wiring harness that routes electrical connections between the control board, heating elements, switches, and other components inside the range. It ensures proper power distribution and signal communication throughout the appliance. Replace this harness if you experience intermittent heating, error codes, or if the wiring shows signs of heat damage, melting, or broken connectors.

Replacement mounting screw for refrigerators, ovens, ranges, and cooktops. Secures interior panels, components, and trim. Needed when original is stripped, missing, or damaged during repair.

Replacement 10-24 x 3/8 machine screw secures panels, brackets, and trim in ranges and ovens. Replace missing, stripped, or damaged screws.

Shoulder screw secures oven components with built-in spacer for proper alignment. Replace worn, missing, or stripped fasteners to restore fit.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Specs: 8 - 18 x 0.500

Spacer that maintains proper gap between components in your range or oven assembly. Replace if missing, worn, or damaged to restore correct fit and alignment.

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head