Parts for Frigidaire CGES3045KW2: 09 - Door Parts

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This heat-resistant insulation helps contain oven heat and shield surrounding components. Replacing worn insulation supports faster, more consistent preheating, steadier baking temperatures, and cooler exterior panels for safer, more efficient operation. What it does:

• Wraps/lines the oven cavity or panels to reduce heat loss and protect nearby wiring and controls
• Helps the oven preheat efficiently and maintain consistent cooking temperatures
• Limits heat transfer to exterior panels and surrounding cabinetry
• Common signs of failure: longer preheat times, temperature swings, unusually hot sides/back, or insulation that is burnt, brittle, soaked, or missing

• 1 insulation piece

• Disconnect power and, if applicable, shut off gas before servicing
• Access typically requires removing rear/side panels or sliding the unit out; take photos to aid reassembly
• Wear gloves and a dust mask; handle gently—do not compress insulation and keep clear of sensors/wiring
• Re-secure with original clips/tape, reinstall panels, then test preheat and check for abnormal exterior heat

The Inner Door Glass is an  OEM replacement part for Frigidaire ranges. It is responsible for providing a safe viewing window into the oven cavity while protecting interior components from external damage.  

Causes of a bad inner door glass include normal wear and tear such as chips or cracks developing from years of use. Accidental impact or thermal shocks from sudden temperature changes can also compromise the integrity of the glass.

Symptoms of a bad inner door glass:

• Cracks or breaks visible in the glass
• Difficulty seeing into the oven cavity clearly 
• Increased risk of heat escaping when the oven is in use
• Potential safety hazards if glass cracks or shatters  

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

This replacement screw secures appliance components and panels. Restore a snug, factory fit when original hardware is missing or stripped, helping prevent rattles, vibration, and misalignment so your unit operates safely and quietly.

• Fastens panels, brackets, or internal parts to the cabinet or frame
• Replaces missing, rusted, or stripped screws
• Helps correct loose or misaligned components
• Reduces rattling or vibration noises caused by loose hardware

• Disconnect power to the appliance before servicing
• Replace one screw at a time to maintain alignment
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; repair damaged threads or replace related clip/insert if needed

This oven door gasket creates a tight seal between the door and the oven frame to hold in heat and help maintain consistent cooking temperatures. Replacing a worn seal can improve preheat times and reduce heat loss and spills from escaping.

• Seals the oven door perimeter to minimize heat and moisture loss
• Helps the oven reach and maintain set temperatures more reliably
• Can address issues like longer preheat, uneven baking, or heat escaping around the door
• Replaces gaskets that are torn, flattened, frayed, or brittle

• Disconnect power and allow the oven to cool completely before service
• Open the door and carefully remove the old gasket from its clips or channel
• Clean the sealing surfaces to remove debris and residue
• Seat the new gasket evenly around the perimeter without stretching or twisting

The Handle is an OEM replacement part for Frigidaire ranges. It is the component located on the front of the oven that allows for opening and closing the oven door.

Causes of a bad handle stem primarily from wear and tear due to frequent use over many years. Exposure to heat cycling may also degrade adhesives or secondary components that secure the handle.

Symptoms of a faulty handle include:

• Difficulty opening or closing the oven door
• The handle detaching from the door
• Sharp edges or broken pieces that compromise safety
• Loss of grip or stability while moving the door

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.