Parts for Frigidaire FFTR1820SW2: 02 - Door Parts

This freezer door gasket is an OEM replacement part for Frigidaire refrigerators. The gasket measures approximately 28" wide x 18" long. This gasket is a perfect fit for your refrigerator's inner door panel.

Symptoms of a bad freezer door gasket include:

• Difficulty keeping interior cold temperatures below 0°F  
• Frost buildup around top and sides of door seals
• Defrosts required increasing in frequency
• Visible air gaps noticeable along gasket perimeter

Causes of a bad freezer door gasket can include material breakdown due to hundreds of door opening and closing compression cycles over time developing small cracks in the rubber. Spills along bottom edges may promote seal deterioration if not cleaned promptly.

This genuine Frigidaire replacement gasket is compatible with other brands such as Electrolux and Kenmore as well 

NOTE: To achieve a smooth installation, simply soak the gasket in warm water or use a hair dryer on low heat to eliminate any folds or creases.

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. This crucial component is responsible for creating an airtight seal around the refrigerator door, ensuring efficient temperature control and energy conservation. This gasket is "approximately" 28” by 41”, and may require a screwdriver to remove the old gasket.

Symptoms of needing to replace the refrigerator door gasket include:

• Difficulty in closing the refrigerator door properly
• Visible gaps or gaps around the door gasket area
• Condensation buildup or frost formation around the door gasket
• Increased energy consumption due to inefficient sealing

Causes of a faulty door gasket can include normal wear and tear over time, exposure to extreme temperatures or UV light, or physical damage due to impact or mishandling.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

The Door Shelf is an OEM replacement part for Frigidaire refrigerators. This gallon door shelf measures about 23 inches wide from inside to inside. 

Causes of a bad door shelf can include frequent use, overloading, or accidental impacts, leading to cracks, breaks, or warping. When the door shelf is damaged, it can compromise the stability and security of stored items, making it less effective for storage needs.

Symptoms of a bad part may include- 

• Cracks or breaks in the plastic
• Difficulty holding items securely in place 
• Shelf not staying attached to the door 
• Difficulty closing the door

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Refrigerator Door Shelf is an OEM replacement part for Frigidaire refrigerators that provides storage space on the refrigerator door. This shelf is designed to fit securely on the door, offering a convenient place to store condiments, bottles, and other items for easy access. The package includes one door shelf. The shelf measures approximately 23”.

Over time, the shelf can crack or break due to frequent use, overloading, or accidental impacts. A faulty door shelf can result in items falling or not being securely held in place.

Symptoms of a bad part include:

• Sagging or broken shelves
• Items falling off the shelf
• Difficulty in opening or closing the refrigerator door

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Dairy Door is an OEM replacement part for  Frigidaire side-by-side refrigerators. Located inside the fresh food compartment, it provides a dedicated storage area for milk, yogurt, cheese and other dairy products requiring colder temperatures. The door measures approximately 9 inches wide and 5 inches high.

Causes of a bad dairy door include normal wear from repeated opening and closing over time. Exposure to spills inside the refrigerator can also potentially damage door shelf components or seals.

Symptoms of a bad dairy door are: 

• Difficulty opening or closing the door smoothly  
• Door alignment issues where it does not sit flush in the frame
• Leaks or moisture inside the dairy storage area
• Damage or cracks in shelf supports or gasket seals

This OEM part is also compatible with models from brands like Electrolux, Gibson, and Kelvinator brand models.

NOTE: For white use 240337701

The Freezer Door Shelf is an OEM part for Frigidaire side-by-side refrigerators. It provides adjustable storage within the freezer compartment for easy access to items. The shelf measures about 24 inches long and 5 inches wide.

Causes of a bad freezer door shelf can include wear over time from repeated loading/unloading that causes scratches or cracks in the lightweight plastic. Exposure to slushy spills may promote material breakdown if not cleaned promptly. 

Symptoms of a bad freezer door shelf include:

• Sagging or inability to bear weight of frozen packages
• Breakage leaving smaller pieces that could fall  
• Discoloration compromising appearance and sanitation
• Shelving that won't stay level or properly positioned

This genuine Frigidaire shelf is also compatible with Electrolux and Kenmore models.

Color: White. Used to cover the hinge bearing hole.

Color: White

A replacement name plate that restores the appliance's factory identification label so model and serial information are legible for service and parts lookup. Helps maintain the appliance's appearance and accurate identification. What it does:

• Provides the factory identification area showing model/serial and manufacturer data for parts lookup and service.
• Use when the original label is missing, scratched, faded, or peeling and no longer readable.
• Restores exterior appearance where the original name plate has cosmetic damage.

• Clean and dry the mounting surface before installing; remove old adhesive residue if present.
• Align carefully and press firmly; some installations may require removal of trim or a cover.
• Use appropriate tools and avoid sharp solvents that could damage surrounding surfaces.

This door stop limits the refrigerator door's opening range to protect hinges and nearby cabinets. Replace a cracked or missing stop to restore smooth, controlled door movement and help the door close and seal properly.

• Limits door swing to prevent overextension and impact with walls or cabinets
• Reduces hinge stress and helps maintain proper door alignment
• Common signs of failure: door opens too far, binds at the hinge, or the original stop is cracked/missing
• Restores smooth, controlled door motion and closure

• Disconnect power and remove items from the door to reduce weight
• Support the door before loosening any hinge fasteners
• Install the new stop in the correct orientation for your model
• Adjust hinges if needed

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

Color: White

The Door Handle Kit is an OEM part for Frigidaire refrigerators. This kit includes the door handle and the necessary mounting hardware to ensure a secure fit. The kit is comprised of one door handle, along with three screws for attachment. It also comes with a set of instructions to guide users through the installation process. 

Over time, door handles can become loose, cracked, or break entirely due to frequent use, mishandling, or impact. Replacing a worn or damaged door handle is essential to maintain the functionality and appearance of the refrigerator.

Symptoms of a bad door handle include:

• Difficulty in opening or closing the refrigerator door
• A loose or wobbly handle
• Visible cracks or breakage in the handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Handle Kit is an OEM part for Frigidaire refrigerators. This kit includes the door handle and the necessary mounting hardware to ensure a secure fit. The kit is comprised of one door handle, along with three screws for attachment. It also comes with a set of instructions to guide users through the installation process. 

Over time, door handles can become loose, cracked, or break entirely due to frequent use, mishandling, or impact. Replacing a worn or damaged door handle is essential to maintain the functionality and appearance of the refrigerator.

Symptoms of a bad door handle include:

• Difficulty in opening or closing the refrigerator door
• A loose or wobbly handle
• Visible cracks or breakage in the handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures select refrigerator door handles to the door. A worn or missing screw can leave the handle loose or detached, making the door difficult to open and potentially stressing other components.

• Holds the door handle firmly to the door
• Helps restore proper door operation and safe grip
• Designed to fit designated mounting points for compatible models

• Unplug the refrigerator before beginning work
• Open the door to access the handle mounting points
• Use the correct screwdriver/Allen tool to avoid stripping the head
• Start threads by hand and tighten snugly—do not overtighten

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It plays a critical role in the smooth operation of the refrigerator door by providing a pivot point for the hinge. This small component helps to ensure that the door opens and closes smoothly and seals properly, which is essential for maintaining the refrigerator's internal temperature and energy efficiency.

Symptoms of a bad Hinge Bearing include:

• Difficulty in opening or closing the refrigerator door.
• Squeaking or grinding noises when the door moves.
• The door hanging unevenly or not sealing correctly, potentially leading to temperature fluctuations inside the fridge.

Causes of a bad hinge bearing can include wear and tear from the frequent use of the refrigerator door, accumulation of dirt or grime that impedes smooth movement, or degradation of the material over time due to environmental factors such as moisture.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a service wrench used to loosen and tighten appliance fasteners for maintenance and repairs, making access and part replacement easier for technicians and DIYers. Durable tool designed for specific appliance fastener sizes. What it does:

• Provides the correct fit and leverage for removing or installing designated appliance nuts, bolts, and fittings
• Helps safely access internal components during service and part replacement
• Reduces risk of rounding fasteners compared with improvised tools
• Useful for routine maintenance tasks and repair procedures that require a dedicated wrench

• One wrench

• Use the wrench only for its intended appliance fasteners; avoid excessive force
• Disconnect power and water to the appliance before beginning service
• Wear safety gloves and eye protection when working on appliances