Parts for Frigidaire GLFH21F8HBB: 03 - Door Parts

This door gasket creates a tight seal between the appliance door and cabinet to keep interior temperatures stable and moisture out. Replacing a worn gasket restores a firm door close and helps reduce frost and energy loss. What it does

• Seals the door perimeter to prevent air leaks
• Helps maintain proper temperature and humidity inside the compartment
• Reduces frost/ice buildup and surface condensation around the door
• Common symptoms: torn/cracked or warped gasket, poor door seal or door popping open, frost at the door edge, moisture on the gasket, temperature fluctuations

• 1 door gasket

• Disconnect power before servicing
• Let the new gasket relax (room temperature or warm water); use a hair dryer on low to smooth waves
• Remove the old gasket from its retainer/channel and seat the new one fully, starting at the corners
• Close the door and check for uniform contact around the perimeter; gently heat/reshape as needed and allow time for the gasket to conform

This small replacement clip secures trim, panels and small appliance components to keep them aligned and stable, helping prevent rattles and maintain proper fit. It's a simple, low-cost fix for loose or missing retainers. What it does

• Secures trim pieces, panels or small components in place
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment of fitted panels and retainers
• Keeps covers and wiring runs routed where intended

• Disconnect power to the appliance before attempting any repairs
• Remove adjacent panels or trim as needed to access the mounting location
• Press or snap the clip into the mating slot; use pliers for leverage if required
• Replace any damaged clips with new ones to ensure a secure fit

The Freezer Door Key is an OEM replacement part for Frigidaire refrigerators. This small but essential component is designed to securely lock the freezer door, preventing accidental openings or unauthorized access.

Symptoms of needing to replace the freezer door key include:

• Difficulty in locking or unlocking the freezer door
• The key not fitting properly or becoming stuck in the lock
• Visible wear, damage, or breakage of the key itself

Causes of a faulty freezer door key can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the locking mechanism itself.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

This inner door panel replaces a damaged or worn interior door surface to restore proper bin support and the refrigerator's finished appearance. It provides a stable mounting surface for door bins and internal hardware. What it does

• Replaces a cracked, warped, or damaged inner door surface that can let door bins sit unevenly or rattle.
• Provides the structural mounting area for door bins, shelves, and hardware.
• Restores the door's finished interior appearance and helps maintain proper fitment of interior components.
• Helps prevent moisture and debris from entering the inner door cavity when intact.

• Disconnect power to the appliance before starting any repair.
• Remove door-mounted items (bins, shelves, gasket, and trim) and retain all fasteners for reassembly.
• Handle the panel carefully to avoid cracking; support the door if removing it from the cabinet.

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This bearing installs in the refrigerator/freezer door hinge to provide a smooth pivot point and maintain alignment. Replacing a worn bearing restores easy door movement and helps the door close and seal correctly.

• Provides a low-friction surface between the hinge pin and hinge bracket for smooth door pivoting
• Helps maintain proper door height and alignment for a reliable gasket seal
• Typical symptoms of wear: squeaking or grinding when opening, door binding or dropping, door not closing fully or popping open
• Excess wear can contribute to air leaks and frost buildup around the door

• Disconnect power before servicing; remove or secure items in the door
• Support the door; remove hinge fasteners and lift the door off if required
• Note and retain any shims/spacers; install the new bearing in the hinge as oriented in the diagram
• Reinstall and align the door; verify smooth operation and a complete gasket seal. Do not lubricate unless specified by the manufacturer

This door gasket creates an airtight seal around your refrigerator or freezer door or lid, keeping cold air in and moisture out. Replace a worn gasket to restore temperature control, reduce frost, and support efficient operation.

• Forms a tight perimeter seal between the cabinet and door/lid to prevent air leaks
• Helps maintain stable internal temperatures and consistent cooling performance
• Reduces frost and condensation caused by a failed or leaking seal
• Common symptoms: visible tears or cracks, gaps, warping/shrinkage, door not sealing or staying closed

• Disconnect power; remove items from the door/lid as needed
• Warm the new gasket (soak in warm water or gently heat) to make it pliable, then straighten corners
• Fit the gasket into the channel or under the retainer, working evenly around the perimeter
• Check closure all around with a paper test; adjust hinges/leveling as needed and allow the gasket to relax and conform

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

This door shelf bin attaches to the inner door panel to hold bottles, jars, and small items. Replacing a cracked or missing bin restores secure, organized storage and helps prevent items from tipping or falling during use.

• Provides on-door storage for jars, condiments, and similar items
• Snaps into the door liner to keep items in place during opening/closing
• Replace if cracked, warped, or if end tabs are broken and the bin won't stay seated
• Symptoms include reduced door storage, items falling, or the bin popping loose

• Disconnect power before servicing
• Remove contents, then lift the old bin up and out of the door liner retainers
• Align the new bin with the slots and press down until it locks fully in place
• Distribute weight evenly and avoid overloading to prevent future damage

The Door Bin is an OEM replacement part for Frigidaire refrigerators. It is an internal door that controls access to the bin storage compartment. This bin area provides additional shelving and can be used to neatly organize larger refrigerated items. This shelf measures approximately 14.25 x 6 inches.

Causes of a bad door bin can include damage to the hinges from frequent opening and closing or impact from heavy items, issues with the door latch or magnets not securely holding the door in closed position.

Symptoms of a bad bin include:

• The door not closing or latching properly
• Gaps allow cool air to escape from the storage area
• Difficulty accessing items inside the storage bin
• Lean or sag over time due to compromised hinges

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This left-side tiltout end cap replaces the damaged or worn plastic end piece that secures and guides a fridge/freezer tilt-out or dairy bin. Restores a secure fit and smooth opening for the tilt-out assembly. What it does:

• Replaces the left end cap on a tilt-out/dairy bin assembly
• Helps keep the drawer aligned and held in place during use
• Reduces rattling or catching when opening and closing the tilt-out
• Matches OEM fit and mounting points for direct replacement

• One left tiltout end cap

• Remove contents and the tilt-out bin before attempting replacement
• Installation typically requires basic hand tools and gentle prying to disengage clips
• Inspect mating clips and housing; replace or repair any broken tabs before reinstalling

This is a right-side tilt-out end cap that replaces a damaged or missing end piece on a refrigerator/freezer tilt-out bin. Restores secure mounting and proper pivoting of the bin for smooth opening and closing. What it does:

• Serves as the right end support for a tilt-out bin, providing the pivot point and cosmetic trim
• Keeps the bin aligned so it opens and closes smoothly
• Replaces cracked, broken, or worn end caps that allow the bin to sag or fall out
• Helps prevent rattling and excessive play of the tilt-out bin

• One right-side tilt-out end cap

• High-level snap-in or screw-mount replacement; remove the bin and follow OEM instructions
• Remove stored items before servicing and support the bin while replacing the cap
• Use basic hand tools; avoid forcing parts to prevent further damage

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

The Control Module is an OEM part for Frigidaire refrigerators. This electronic component manages and regulates the various functions of the refrigerator, including temperature control, defrost cycles, and the operation of fans and compressors.

You should replace the control module if it fails or malfunctions. Causes of a bad control module can include electrical surges, wear and tear over time, or exposure to moisture. Faulty wiring or damaged components within the module can also lead to failure.

Symptoms of a bad control module include:

• Inconsistent or incorrect temperatures in the refrigerator or freezer
• Refrigerator not cooling properly
• Frequent cycling on and off of the compressor
• Error codes displayed on the control panel

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Note: Control Only - Touchpad and housing no longer included.

This nut-anchor is a small mounting insert that provides a secure threaded point in thin sheet metal so screws can fasten panels or components reliably. It restores a solid attachment where the original fastener or threaded hole is missing. What it does:

• Provides a reinforced threaded anchor in thin metal or plastic panels
• Allows screws to tighten without stripping the sheet material
• Stops panels, trim, or assemblies from coming loose or rattling
• Used where a captive nut or threaded insert is required for reassembly

• Install where original nut/insert was located; verify orientation before fastening
• Use the correct screw size and hand-tighten to avoid overtightening or thread damage
• Disconnect power and move the appliance to a safe, stable work area before servicing
• If the original mounting point is severely damaged, consider assessing the surrounding structure for repair

The Refrigerator Door Gasket Clips are OEM parts for Frigidaire refrigerators. These clips secure the door gasket in place, ensuring a tight seal to maintain the internal temperature and prevent cold air from escaping. This pack contains 40 clips, which secure the interior trim pieces and hold the gasket and liner to the freezer lid.

Over time, the gasket clips can become damaged or worn out due to frequent opening and closing of the refrigerator door, exposure to moisture, or accidental impacts. If the clips fail, the door gasket may not stay in place, compromising the refrigerator's efficiency.

Symptoms of bad refrigerator door gasket clips include:

• The door gasket not staying securely in place
• Visible damage or wear on the clips
• Cold air escaping from around the door
• Increased energy consumption due to poor sealing

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.