Parts for Frigidaire LFUH21F7LM2: 03 - Door Parts

This refrigerator door gasket seals the fresh food compartment to keep cold air in and warm air out. A tight, pliable seal helps maintain temperature, reduce frost and energy use, and prevent moisture around the door.

• Creates an airtight seal between the fresh food door and cabinet
• Helps with issues like warm fridge section, condensation at the door, or doors not closing securely
• Can reduce frost or moisture buildup caused by air leaks
• Restores proper door alignment/seal if the old gasket is warped, torn, or hardened

• Unplug the appliance before starting
• Soften the new gasket by laying it flat at room temperature; warming with a hair dryer on low can help relax folds
• Remove the old gasket and press the new one fully into the retainer, working evenly around corners
• Check for even contact all around; adjust the door and use gentle heat to relax high spots for a tight seal

The Freezer Door Key is an OEM replacement part for Frigidaire refrigerators. This small but essential component is designed to securely lock the freezer door, preventing accidental openings or unauthorized access.

Symptoms of needing to replace the freezer door key include:

• Difficulty in locking or unlocking the freezer door
• The key not fitting properly or becoming stuck in the lock
• Visible wear, damage, or breakage of the key itself

Causes of a faulty freezer door key can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the locking mechanism itself.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

This inner door panel replaces a damaged or worn interior door surface to restore proper bin support and the refrigerator's finished appearance. It provides a stable mounting surface for door bins and internal hardware. What it does

• Replaces a cracked, warped, or damaged inner door surface that can let door bins sit unevenly or rattle.
• Provides the structural mounting area for door bins, shelves, and hardware.
• Restores the door's finished interior appearance and helps maintain proper fitment of interior components.
• Helps prevent moisture and debris from entering the inner door cavity when intact.

• Disconnect power to the appliance before starting any repair.
• Remove door-mounted items (bins, shelves, gasket, and trim) and retain all fasteners for reassembly.
• Handle the panel carefully to avoid cracking; support the door if removing it from the cabinet.

This door handle assembly replaces a damaged or missing refrigerator door handle to restore a secure grip and normal door operation. It provides a direct-fit replacement when the existing handle is cracked, loose, or cosmetically worn. What it does:

• Replaces a broken or cracked door handle so you can open and close the refrigerator normally
• Secures to the cabinet to prevent wobbling, loose hardware, or sudden handle failure
• Restores the original look when the handle is scratched, chipped, or discolored
• Works with the factory mounting points for a proper fit and alignment

• Disconnect power only when working near electrical components; removing a door handle does not typically require shutting off power to the appliance.
• Remove food and items from the door and work on a stable surface to avoid damage.
• Keep all mounting screws and caps from the old handle for reuse unless new fasteners are supplied.
• Use common hand tools; avoid overtightening screws to prevent cracking the handle or trim.

This replacement screw secures panels, brackets, or internal components in select Frigidaire-made refrigerators and freezers. Use it to replace missing or stripped hardware and restore a secure fit to help reduce vibration and noise.

• Fastens appliance panels, brackets, and internal components
• Helps prevent vibration, rattling, or looseness from missing hardware
• Reliable fix when the original screw is missing, damaged, or stripped
• Designed for proper fit in the original threaded location(s) specified for this part number

• Disconnect power to the appliance before servicing
• Align parts and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten, especially into plastic components
• Reuse any original washers or clips if present and in good condition

This bearing installs in the refrigerator/freezer door hinge to provide a smooth pivot point and maintain alignment. Replacing a worn bearing restores easy door movement and helps the door close and seal correctly.

• Provides a low-friction surface between the hinge pin and hinge bracket for smooth door pivoting
• Helps maintain proper door height and alignment for a reliable gasket seal
• Typical symptoms of wear: squeaking or grinding when opening, door binding or dropping, door not closing fully or popping open
• Excess wear can contribute to air leaks and frost buildup around the door

• Disconnect power before servicing; remove or secure items in the door
• Support the door; remove hinge fasteners and lift the door off if required
• Note and retain any shims/spacers; install the new bearing in the hinge as oriented in the diagram
• Reinstall and align the door; verify smooth operation and a complete gasket seal. Do not lubricate unless specified by the manufacturer

This door gasket creates an airtight seal around your refrigerator or freezer door or lid, keeping cold air in and moisture out. Replace a worn gasket to restore temperature control, reduce frost, and support efficient operation.

• Forms a tight perimeter seal between the cabinet and door/lid to prevent air leaks
• Helps maintain stable internal temperatures and consistent cooling performance
• Reduces frost and condensation caused by a failed or leaking seal
• Common symptoms: visible tears or cracks, gaps, warping/shrinkage, door not sealing or staying closed

• Disconnect power; remove items from the door/lid as needed
• Warm the new gasket (soak in warm water or gently heat) to make it pliable, then straighten corners
• Fit the gasket into the channel or under the retainer, working evenly around the perimeter
• Check closure all around with a paper test; adjust hinges/leveling as needed and allow the gasket to relax and conform

A small replacement mounting clip that secures interior trim or panels on select refrigerators, helping restore a snug fit and reduce loose, rattling parts. Fits where worn or broken clips allow trim to shift. What it does:

• Holds trim, panels or small components in place to prevent rattling and movement.
• Restores proper alignment of affected panels so edges sit flush and look finished.
• Simple mechanical fastening — replaces brittle or broken clips that no longer grip.
• Helps reduce noise caused by loose interior parts during normal operation.

• Always unplug the appliance or switch off power at the breaker before servicing.
• Remove the affected trim or panel per manufacturer instructions to access the clip location.
• Press the clip into the mating slot or post until it seats securely; use a small tool if needed to avoid fingernail or surface damage.
• Inspect surrounding mounting surfaces for cracks or wear; damaged supports may require additional replacement parts.

The Door Shelf Bin is an OEM part for Frigidaire refrigerators. It provides storage for commonly used items along the inside of the refrigerator door.

Symptoms of a bad door shelf bin include:

• Cracks or fractures developing in the plastic
• Difficulty removing or replacing bin due to loose brackets  
• Items falling through or wedging into bin openings
• Missing brackets rendering the bin unusable

Causes of a bad door shelf bin can be normal wear over extended use periods, damage from overloading or dropping heavy items, or stresses from repeated door closings.

Replacing with this OEM bin restores useful door storage space. Compatible with existing mounting locations, it supports organization within busy kitchens.  

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace to avoid further breakdowns.
 

The Door Bin is an OEM replacement part for Frigidaire refrigerators. It is an internal door that controls access to the bin storage compartment. This bin area provides additional shelving and can be used to neatly organize larger refrigerated items. This shelf measures approximately 14.25 x 6 inches.

Causes of a bad door bin can include damage to the hinges from frequent opening and closing or impact from heavy items, issues with the door latch or magnets not securely holding the door in closed position.

Symptoms of a bad bin include:

• The door not closing or latching properly
• Gaps allow cool air to escape from the storage area
• Difficulty accessing items inside the storage bin
• Lean or sag over time due to compromised hinges

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This left-side tiltout end cap replaces the damaged or worn plastic end piece that secures and guides a fridge/freezer tilt-out or dairy bin. Restores a secure fit and smooth opening for the tilt-out assembly. What it does:

• Replaces the left end cap on a tilt-out/dairy bin assembly
• Helps keep the drawer aligned and held in place during use
• Reduces rattling or catching when opening and closing the tilt-out
• Matches OEM fit and mounting points for direct replacement

• One left tiltout end cap

• Remove contents and the tilt-out bin before attempting replacement
• Installation typically requires basic hand tools and gentle prying to disengage clips
• Inspect mating clips and housing; replace or repair any broken tabs before reinstalling

This is a right-side tilt-out end cap that replaces a damaged or missing end piece on a refrigerator/freezer tilt-out bin. Restores secure mounting and proper pivoting of the bin for smooth opening and closing. What it does:

• Serves as the right end support for a tilt-out bin, providing the pivot point and cosmetic trim
• Keeps the bin aligned so it opens and closes smoothly
• Replaces cracked, broken, or worn end caps that allow the bin to sag or fall out
• Helps prevent rattling and excessive play of the tilt-out bin

• One right-side tilt-out end cap

• High-level snap-in or screw-mount replacement; remove the bin and follow OEM instructions
• Remove stored items before servicing and support the bin while replacing the cap
• Use basic hand tools; avoid forcing parts to prevent further damage

This part number contains one (1) screw.

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

The Control Module is an OEM part for Frigidaire refrigerators. This electronic component manages and regulates the various functions of the refrigerator, including temperature control, defrost cycles, and the operation of fans and compressors.

You should replace the control module if it fails or malfunctions. Causes of a bad control module can include electrical surges, wear and tear over time, or exposure to moisture. Faulty wiring or damaged components within the module can also lead to failure.

Symptoms of a bad control module include:

• Inconsistent or incorrect temperatures in the refrigerator or freezer
• Refrigerator not cooling properly
• Frequent cycling on and off of the compressor
• Error codes displayed on the control panel

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Note: Control Only - Touchpad and housing no longer included.