Parts for Ge ZGP304LR5SS: Door Parts

This small end cap fits the end of an extension piece to act as a stop and finish. It restores a secure, finished edge so the sliding component or trim stays aligned and doesn't over-travel during use.

• Caps the end of an extension rail or trim to prevent over-travel and pullout
• Keeps the assembly aligned to reduce wobble
• Replaces cracked, missing, or worn caps
• Helps eliminate rattling and exposed edges

• Disconnect power and allow all hot surfaces to cool before servicing
• Access the end of the extension/rail; release any locking tab and remove the old cap
• Align and snap or press the new cap into place
• Verify smooth travel and a secure stop after installation

This is a replacement 8-18 x 5/16 machine screw used to secure appliance panels and components. It restores proper fastener fit so parts stay mounted and operate safely. What it does:

• Fastens panels, brackets, and small components where an 8-18 x 5/16 screw is specified
• Prevents loose parts, rattling, and misalignment caused by missing or worn screws
• Provides the correct thread size and length for reliable reattachment
• Works wherever the OEM calls for this specific 8-18 x 5/16 screw

• Turn off and unplug the appliance before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to threads or mounting surfaces
• If replacing multiple fasteners, use matching screws to maintain proper fit and function

This replacement upper refrigerator door insulation restores thermal barrier in the top section of the door to help maintain proper cooling and reduce frost build-up. It fits behind the inner door panel as the factory insulation. What it does

• Replaces compressed or damaged insulation that can let cold escape from the cabinet
• Helps maintain consistent internal temperatures and reduce compressor run time
• Can reduce localized frost or moisture on the door interior caused by lost insulation
• Restores intended spacing between inner panel and outer door for proper fit and seal

• Disconnect power to the appliance before beginning any repair.
• Removal of the inner door panel or trim may be required; retain all fasteners for reassembly.
• Handle panels and insulation carefully to avoid tearing or shifting the material.

The Door Hinge (Right) is an OEM part for GE gas ranges. It acts as the pivot point allowing the right side of the range door to smoothly and securely open and close.

Causes include normal wear and tear from repeated use, accidental impacts deforming the hinge, or deterioration of spring components.

Symptoms of a bad right door hinge include:

• Resistance felt only when opening/closing the right side of the door  
• Noise, rubbing or squeaking coming from the right hinge area
• Visual bending or damage evident on the hinge itself
• Improper alignment of just the right side causing sealing issues

This OEM replacement is compatible with Hotpoint, RCA, and select Kenmore gas range models.

The Door Hinge (Left) is an OEM part for GE gas ranges. This hinge is responsible for securely and smoothly mounting the oven door to allow easy access to the cooking cavity. 

Causes of a bad hinge include normal wear and tear from years of opening and closing the heavy oven door. The repeated motion can cause hinge mechanisms to loosen, fail to properly support the door weight, or become misaligned over time.

Symptoms of a bad hinge (left) include: 

• The oven door sagging or unable to stay open on its own  
• Difficulty smoothly opening and closing the door
• Noisy or gritty motion from the hinge when in use
• Improper alignment that impacts sealing of the door

This genuine GE replacement hinge is compatible with some Hotpoint and RCA models as well. 

This replacement screw secures appliance components so panels, brackets, and trim stay tight and aligned. Use it to replace a missing, stripped, or rusted fastener and restore a solid, rattle-free fit in the affected assembly.

• Fastens parts to the chassis/frame or mounting brackets
• Replaces lost, damaged, or corroded hardware
• Can help address loose or vibrating panels and minor misalignment
• Maintains a secure attachment during normal operation

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Match the screw to the original location and reuse any clips or washers if present
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Repair/replace damaged receiving threads or clip for proper hold

This door gasket is the replacement sealing strip that fits around an oven door to help keep heat and moisture inside for more even cooking and energy efficiency. It restores the oven's seal and reduces heat loss during use. What it does:

• Seals the gap between the oven door and cabinet to help maintain cooking temperature
• Helps reduce heat and moisture escaping into the kitchen
• Can improve bake/roast performance when a worn gasket allows leaks
• Common symptom: visible gaps, torn/compressed rubber, or oven failing to hold temperature

• One door gasket

• High-level replacement: remove oven door or access clips/retainer, pull out old gasket, and press new gasket into the retainer channel
• Use gloves to protect your hands; allow the oven to cool completely before starting
• Check gasket orientation and that it seats evenly around the full perimeter for a proper seal