Parts for Jenn-Air W206B: 04 - Door Parts

This oven door seal creates a tight, heat-resistant barrier between the oven door and front frame. A good seal helps the oven heat efficiently and prevents hot air from escaping into your kitchen.

• Cushions and seals the perimeter of the main oven door to contain heat
• Helps maintain stable cooking temperatures and energy efficiency
• Resolves issues like heat escaping around the door, uneven baking, longer preheat times, or visible gaps in the gasket
• Replaces a flattened, brittle, cracked, or torn door gasket

• Disconnect power and allow the oven to cool completely before service
• Open the door and remove the old gasket from its retaining clips or channel
• Press the new seal evenly into place, ensuring corners seat fully
• After installation, check door alignment and seal contact all around

This oven door seal forms a heat-resistant barrier around the door opening to keep heat in and stabilize temperatures. Replacing a worn seal helps restore proper door closure, efficient heating, and consistent baking performance.

• Seals the gap between the door and oven front to prevent hot air and steam from escaping
• Helps maintain stable cavity temperature and more even cooking results
• Replace if the seal is torn, frayed, hardened, flattened, or if you notice heat escaping, longer preheat times, or temperature fluctuations

• Disconnect power or gas and allow the oven to cool completely before servicing
• Open the door, remove the old seal, and clean the channel or retainers
• Press the new seal into the existing clips/retainers without stretching; align corners evenly
• After installation, verify the door closes snugly and perform a brief preheat to help seat the seal

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This part has been discontinued and is no longer available.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This part has been discontinued by the manufacturer and is no longer available.

The Screw is an OEM part for Whirlpool appliances. This specific screw is used in various locations within Whirlpool appliances, securing components and ensuring the stability and proper alignment of parts. It is designed to fit precisely and maintain a firm hold, contributing to the overall functionality and safety of the appliance.

Over time, screws can become worn or stripped due to regular use, corrosion, or over-tightening. 

Causes of a bad screw include wear and tear, exposure to moisture leading to rust, and over-tightening which can strip the threads.

Symptoms of a bad screw include:

• Loose or wobbly components
• Misalignment of parts
• Noise due to vibrating or loose parts
• Difficulty in securing or removing the screw

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement door handle restores a secure, comfortable grip for opening and closing the appliance door. Built to match the OEM fit and mounting points, it replaces worn, cracked, or broken handles to improve everyday use. What it does:

• Replaces a damaged or worn door handle so the door can be opened and closed easily
• Provides the correct mounting points and alignment for a factory fit
• Restores a secure grip and normal operation when original handle is loose, cracked, or broken
• Helps prevent further damage to the door edge or trim caused by using a broken handle

• Disconnect power (and water, for appliances with water connections) before starting any repair.
• Installation typically requires removing the inner door panel or trim; keep screws and fasteners organized.
• Hand tools only—avoid over-tightening fasteners to prevent cracking the replacement handle.

The Screw is an OEM part for Whirlpool appliances. This specific screw is used in various locations within Whirlpool appliances, securing components and ensuring the stability and proper alignment of parts. It is designed to fit precisely and maintain a firm hold, contributing to the overall functionality and safety of the appliance.

Over time, screws can become worn or stripped due to regular use, corrosion, or over-tightening. 

Causes of a bad screw include wear and tear, exposure to moisture leading to rust, and over-tightening which can strip the threads.

Symptoms of a bad screw include:

• Loose or wobbly components
• Misalignment of parts
• Noise due to vibrating or loose parts
• Difficulty in securing or removing the screw

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Oven Door Glass Spacer is an OEM part for Whirlpool ovens. This part helps maintain the structural integrity of the oven door, preventing heat escape, and ensuring the door glass remains securely in place during the oven's operation. 

Causes of a bad Oven Door Glass Spacer can range from wear and tear over time, leading to degradation or loss of the spacer, to improper installation that may cause the spacer to dislodge or fail to provide adequate support. 

Symptoms of a malfunctioning Oven Door Glass Spacer include:

• Loose or rattling oven door glass
• Uneven gaps around the door glass, indicating misalignment
• Heat leaking from around the oven door, potentially affecting cooking performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.