Parts for Kenmore 253.28099809 (25328099809, 253 28099809): Door Parts

This door gasket creates a tight seal between the appliance door and cabinet to keep interior temperatures stable and moisture out. Replacing a worn gasket restores a firm door close and helps reduce frost and energy loss. What it does

• Seals the door perimeter to prevent air leaks
• Helps maintain proper temperature and humidity inside the compartment
• Reduces frost/ice buildup and surface condensation around the door
• Common symptoms: torn/cracked or warped gasket, poor door seal or door popping open, frost at the door edge, moisture on the gasket, temperature fluctuations

• 1 door gasket

• Disconnect power before servicing
• Let the new gasket relax (room temperature or warm water); use a hair dryer on low to smooth waves
• Remove the old gasket from its retainer/channel and seat the new one fully, starting at the corners
• Close the door and check for uniform contact around the perimeter; gently heat/reshape as needed and allow time for the gasket to conform

The Freezer Door Key is an OEM replacement part for Frigidaire refrigerators. This small but essential component is designed to securely lock the freezer door, preventing accidental openings or unauthorized access.

Symptoms of needing to replace the freezer door key include:

• Difficulty in locking or unlocking the freezer door
• The key not fitting properly or becoming stuck in the lock
• Visible wear, damage, or breakage of the key itself

Causes of a faulty freezer door key can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the locking mechanism itself.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

This inner door panel replaces a damaged or worn interior door surface to restore proper bin support and the refrigerator's finished appearance. It provides a stable mounting surface for door bins and internal hardware. What it does

• Replaces a cracked, warped, or damaged inner door surface that can let door bins sit unevenly or rattle.
• Provides the structural mounting area for door bins, shelves, and hardware.
• Restores the door's finished interior appearance and helps maintain proper fitment of interior components.
• Helps prevent moisture and debris from entering the inner door cavity when intact.

• Disconnect power to the appliance before starting any repair.
• Remove door-mounted items (bins, shelves, gasket, and trim) and retain all fasteners for reassembly.
• Handle the panel carefully to avoid cracking; support the door if removing it from the cabinet.

This replacement name plate restores the machine's factory identification label so model and serial information is visible for service, warranty and parts lookup. It helps replace a scratched, missing or unreadable label. What it does:

• Replaces the original identification/nameplate that shows model and serial details
• Restores a legible label when the original is faded, scratched or missing
• Supports accurate documentation for warranty and service calls

• Inspect the mounting area and remove any loose adhesive or debris before installing
• Align the name plate carefully to match the original location; press firmly if adhesive-backed
• If fastened with screws or clips on your model, reuse the original hardware
• Avoid harsh solvents on nearby finishes; wear gloves to keep the label clean during installation

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This bearing installs in the refrigerator/freezer door hinge to provide a smooth pivot point and maintain alignment. Replacing a worn bearing restores easy door movement and helps the door close and seal correctly.

• Provides a low-friction surface between the hinge pin and hinge bracket for smooth door pivoting
• Helps maintain proper door height and alignment for a reliable gasket seal
• Typical symptoms of wear: squeaking or grinding when opening, door binding or dropping, door not closing fully or popping open
• Excess wear can contribute to air leaks and frost buildup around the door

• Disconnect power before servicing; remove or secure items in the door
• Support the door; remove hinge fasteners and lift the door off if required
• Note and retain any shims/spacers; install the new bearing in the hinge as oriented in the diagram
• Reinstall and align the door; verify smooth operation and a complete gasket seal. Do not lubricate unless specified by the manufacturer

This door gasket creates an airtight seal around your refrigerator or freezer door or lid, keeping cold air in and moisture out. Replace a worn gasket to restore temperature control, reduce frost, and support efficient operation.

• Forms a tight perimeter seal between the cabinet and door/lid to prevent air leaks
• Helps maintain stable internal temperatures and consistent cooling performance
• Reduces frost and condensation caused by a failed or leaking seal
• Common symptoms: visible tears or cracks, gaps, warping/shrinkage, door not sealing or staying closed

• Disconnect power; remove items from the door/lid as needed
• Warm the new gasket (soak in warm water or gently heat) to make it pliable, then straighten corners
• Fit the gasket into the channel or under the retainer, working evenly around the perimeter
• Check closure all around with a paper test; adjust hinges/leveling as needed and allow the gasket to relax and conform

A small replacement mounting clip that secures interior trim or panels on select refrigerators, helping restore a snug fit and reduce loose, rattling parts. Fits where worn or broken clips allow trim to shift. What it does:

• Holds trim, panels or small components in place to prevent rattling and movement.
• Restores proper alignment of affected panels so edges sit flush and look finished.
• Simple mechanical fastening — replaces brittle or broken clips that no longer grip.
• Helps reduce noise caused by loose interior parts during normal operation.

• Always unplug the appliance or switch off power at the breaker before servicing.
• Remove the affected trim or panel per manufacturer instructions to access the clip location.
• Press the clip into the mating slot or post until it seats securely; use a small tool if needed to avoid fingernail or surface damage.
• Inspect surrounding mounting surfaces for cracks or wear; damaged supports may require additional replacement parts.

This door shelf bin attaches to the inner door panel to hold bottles, jars, and small items. Replacing a cracked or missing bin restores secure, organized storage and helps prevent items from tipping or falling during use.

• Provides on-door storage for jars, condiments, and similar items
• Snaps into the door liner to keep items in place during opening/closing
• Replace if cracked, warped, or if end tabs are broken and the bin won't stay seated
• Symptoms include reduced door storage, items falling, or the bin popping loose

• Disconnect power before servicing
• Remove contents, then lift the old bin up and out of the door liner retainers
• Align the new bin with the slots and press down until it locks fully in place
• Distribute weight evenly and avoid overloading to prevent future damage

This Freezer Door Bin is an OEM part for Frigidaire refrigerators. Designed specifically for the freezer compartment, it provides a convenient storage solution for organizing and accessing frozen food items.

Causes of a bad freezer door bin can include wear and tear over time, damage from heavy or improperly placed items, or excessive force applied while opening or closing the freezer door. When the bin is in poor condition, it can result in disorganized storage, limited space for items, or difficulty in accessing frozen foods.

Symptoms of a bad freezer door bin may include:

• Cracks or breakage in the bin
• Loose or unstable placement within the freezer
• Inability to hold items securely

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This left-side tiltout end cap replaces the damaged or worn plastic end piece that secures and guides a fridge/freezer tilt-out or dairy bin. Restores a secure fit and smooth opening for the tilt-out assembly. What it does:

• Replaces the left end cap on a tilt-out/dairy bin assembly
• Helps keep the drawer aligned and held in place during use
• Reduces rattling or catching when opening and closing the tilt-out
• Matches OEM fit and mounting points for direct replacement

• One left tiltout end cap

• Remove contents and the tilt-out bin before attempting replacement
• Installation typically requires basic hand tools and gentle prying to disengage clips
• Inspect mating clips and housing; replace or repair any broken tabs before reinstalling

This is a right-side tilt-out end cap that replaces a damaged or missing end piece on a refrigerator/freezer tilt-out bin. Restores secure mounting and proper pivoting of the bin for smooth opening and closing. What it does:

• Serves as the right end support for a tilt-out bin, providing the pivot point and cosmetic trim
• Keeps the bin aligned so it opens and closes smoothly
• Replaces cracked, broken, or worn end caps that allow the bin to sag or fall out
• Helps prevent rattling and excessive play of the tilt-out bin

• One right-side tilt-out end cap

• High-level snap-in or screw-mount replacement; remove the bin and follow OEM instructions
• Remove stored items before servicing and support the bin while replacing the cap
• Use basic hand tools; avoid forcing parts to prevent further damage

This part number contains one (1) screw.

This electronic control board is the freezer's central control module. It processes sensor inputs and user settings to run the cooling system and alerts. Replacing a failed board helps restore reliable operation and accurate temperature management. What it does:

• Controls compressor and evaporator fan operation to maintain the set temperature
• Interprets thermistor input and applies control logic to regulate cooling
• Coordinates features such as alarms and, on electronic models, defrost cycles
• Common symptoms include the unit not running or powering up, warming or unstable temperatures, unresponsive or erratic controls/display, or excessive frost buildup

• Disconnect power before servicing; handle the board with ESD precautions
• Access the control housing, note wire locations, and transfer connectors one at a time
• Secure the replacement board and reuse original mounting hardware and any reusable trim/overlay as applicable
• Restore power, set temperatures, and allow up to 24 hours for stabilization

This nut-anchor is a small mounting insert that provides a secure threaded point in thin sheet metal so screws can fasten panels or components reliably. It restores a solid attachment where the original fastener or threaded hole is missing. What it does:

• Provides a reinforced threaded anchor in thin metal or plastic panels
• Allows screws to tighten without stripping the sheet material
• Stops panels, trim, or assemblies from coming loose or rattling
• Used where a captive nut or threaded insert is required for reassembly

• Install where original nut/insert was located; verify orientation before fastening
• Use the correct screw size and hand-tighten to avoid overtightening or thread damage
• Disconnect power and move the appliance to a safe, stable work area before servicing
• If the original mounting point is severely damaged, consider assessing the surrounding structure for repair

The Refrigerator Door Gasket Clips are OEM parts for Frigidaire refrigerators. These clips secure the door gasket in place, ensuring a tight seal to maintain the internal temperature and prevent cold air from escaping. This pack contains 40 clips, which secure the interior trim pieces and hold the gasket and liner to the freezer lid.

Over time, the gasket clips can become damaged or worn out due to frequent opening and closing of the refrigerator door, exposure to moisture, or accidental impacts. If the clips fail, the door gasket may not stay in place, compromising the refrigerator's efficiency.

Symptoms of bad refrigerator door gasket clips include:

• The door gasket not staying securely in place
• Visible damage or wear on the clips
• Cold air escaping from around the door
• Increased energy consumption due to poor sealing

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.