Parts for Kenmore 253.70643612 (25370643612, 253 70643612): Door Parts

This freezer door gasket forms an airtight seal around the door to keep cold air in and moisture out. Replacing a worn or damaged gasket helps restore proper temperature, reduce frost, and improve efficiency.

• Creates a continuous perimeter seal between the freezer door and cabinet
• Helps maintain stable freezer temperature and overall performance
• Minimizes frost/ice buildup and condensation around the door
• Replace if torn, cracked, warped, won't stay seated, or if the door won't close flush

• Disconnect power before servicing
• Remove the old gasket from the door channel/retainer and clean the sealing surfaces
• Warm the new gasket with hot water or low heat to relax; press it fully into the channel, working evenly around corners (do not overheat)
• Close the door and check for uniform contact all around; adjust door/hinges if needed and allow time for the gasket to conform

This freezer door gasket creates an airtight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn gasket helps restore proper temperatures, reduce frost and condensation, and improve efficiency.

• Seals the freezer door perimeter to prevent warm-air leaks and temperature swings
• Helps reduce frost buildup and condensation around the door opening
• Can resolve issues like visible gaps, a torn or deformed gasket, or a door that won't seal
• Supports consistent cooling performance and reduces excessive run time

• Disconnect power to the refrigerator before servicing
• Let the new gasket relax at room temperature; use warm water or low heat to smooth folds
• Clean the door sealing surface thoroughly; install the gasket evenly, ensuring corners are fully seated
• Close the door and check for uniform contact all around; gently massage high spots and re-seat as needed

This freezer door gasket creates a tight seal around the door to keep cold air in and humid air out—helping maintain set temperatures, reduce frost buildup, and support efficient, reliable freezer performance. What it does:

• Seals the freezer door perimeter to prevent air leaks and warm air infiltration
• Helps maintain consistent freezer temperature and energy efficiency
• Helps reduce frost/ice buildup and condensation around the door
• A worn, torn, or warped gasket can lead to poor sealing, frost, moisture, or longer run times

• 1 freezer door gasket

• Disconnect power before servicing
• Allow the new gasket to warm and relax (room temperature or warm water) for easier installation; do not overheat
• Remove the old gasket; clean and dry the door channel, then press the new gasket fully into place, starting at the corners
• After installation, check for uniform contact all around; adjust the door/hinges if needed and verify with a paper-slip test

The Gasket-Refr Door is an OEM part for Frigidaire refrigerators, designed to ensure an airtight seal around the door, maintaining the appliance's internal temperature and energy efficiency. This gasket prevents warm air from entering and cool air from escaping the refrigerator, crucial for preserving food freshness and minimizing energy consumption.

Causes of a bad Gasket-Refr Door can include physical wear and tear from regular use, accidental damage, or aging, which can lead to hardening, cracking, or tearing of the gasket material.  

Symptoms of a malfunctioning Gasket-Refr Door include:

• Noticeable gaps or looseness around the door perimeter, indicating a poor seal.
• Increased condensation or frost buildup inside the refrigerator, a sign of air leaks.
• The refrigerator runs more frequently or for longer periods, trying to maintain the set temperature.
• Spoilage of food more quickly than usual, due to temperature inconsistencies.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. As a sealing component, it surrounds the door frame to keep cold air circulating optimally. Proper installation and fit maintains energy efficiency.

Causes of failure involve cracks arising over constant compression and expansion during repeated openings. Mineral buildup may also compromise the seal over time.

Symptoms of a defective gasket include:

• Cooler air detectable escaping around door edges
• Condensation visible on door seal
• Temperature fluctuations noticed inside refrigerator

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.

The Refrigerator Door Gasket is an OEM part for Frigidaire refrigerators, designed to seal the door of the refrigerator compartment, ensuring an airtight closure. This door gasket plays a crucial role in maintaining the efficiency of the refrigerator by preventing cold air from escaping and warm air from entering.

Common causes for a Refrigerator Door Gasket to fail include normal wear and tear from opening and closing the door, damage from cleaning or misuse, and aging of the material, which can lead to hardening and loss of elasticity.

Symptoms of a bad Refrigerator Door Gasket include:

• Noticeable gaps or tears in the gasket
• The refrigerator door does not close as tightly as it should, or it requires more force to close.
• Condensation or frost buildup around the door edges
• An increase in energy consumption

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Dairy Door is an OEM replacement part for  Frigidaire side-by-side refrigerators. Located inside the fresh food compartment, it provides a dedicated storage area for milk, yogurt, cheese and other dairy products requiring colder temperatures. The door measures approximately 9 inches wide and 5 inches high.

Causes of a bad dairy door include normal wear from repeated opening and closing over time. Exposure to spills inside the refrigerator can also potentially damage door shelf components or seals.

Symptoms of a bad dairy door are: 

• Difficulty opening or closing the door smoothly  
• Door alignment issues where it does not sit flush in the frame
• Leaks or moisture inside the dairy storage area
• Damage or cracks in shelf supports or gasket seals

This OEM part is also compatible with models from brands like Electrolux, Gibson, and Kelvinator brand models.

NOTE: For white use 240337701

This small black plug/button covers a hinge or bearing access hole to restore a finished appearance and help keep out dirt and debris. It's a simple, inexpensive trim piece that maintains the appliance's look and helps protect internal components. What it does:

• Covers exposed hinge or bearing access holes for a clean, finished appearance
• Helps keep dust and debris out of hinge or bearing cavities
• Prevents snagging and reduces the chance of small items entering the opening
• Matches factory appearance and fit for a seamless repair

• Push-fit design; press into the hole until fully seated
• Keep away from small children — small part is a choking hazard

This plug button is a small control panel push button used on select Frigidaire appliances to replace a worn or broken button and restore normal user control. It snaps into the panel for a clean, factory-fit appearance. What it does:

• Acts as the tactile push button used to operate a specific control or function on the appliance
• Replaces cracked, loose, or missing buttons that prevent consistent button actuation
• Restores proper contact engagement so the control registers presses reliably
• Helps eliminate cosmetic damage and keeps the control surface sealed against debris

• One plug button

• Snap-in replacement; remove power to the appliance before attempting any service
• If button is attached to an electronics assembly, handle boards and connectors carefully to avoid damage
• Use basic hand tools as needed and avoid forcing parts—verify orientation before snapping into place

Color: White. Used to cover the hinge bearing hole.

This door stop limits the opening range of your refrigerator door to prevent overextension and hinge strain. Replace a worn or broken stop to restore controlled door movement and protect surrounding cabinetry from accidental impacts. What it does:

• Controls how far the door opens to prevent overextension and damage
• Helps maintain proper door alignment and reduces stress on the hinges
• Replaces cracked, deformed, or missing stops that no longer hold the door at its stop point
• Common symptoms include the door swinging too far, a hard "clunk" at full open, or visible damage to the stop

• 1 door stop

• Disconnect power; turn off water supply if your unit has a dispenser/ice maker
• Support the door before loosening any hinge fasteners to access the stop
• Note the stop's orientation and position; transfer any spacers and reinstall the same way
• Open and close the door to verify proper range and clearance before fully tightening fasteners

This door stop limits the refrigerator door's opening range to protect hinges and nearby cabinets. Replace a cracked or missing stop to restore smooth, controlled door movement and help the door close and seal properly.

• Limits door swing to prevent overextension and impact with walls or cabinets
• Reduces hinge stress and helps maintain proper door alignment
• Common signs of failure: door opens too far, binds at the hinge, or the original stop is cracked/missing
• Restores smooth, controlled door motion and closure

• Disconnect power and remove items from the door to reduce weight
• Support the door before loosening any hinge fasteners
• Install the new stop in the correct orientation for your model
• Adjust hinges if needed

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small black replacement plug button that restores a clean, finished appearance and helps keep controls and openings free from dirt and moisture. Designed as a direct-fit cosmetic and protective cap for compatible appliance openings. What it does

• Covers exposed holes or button openings to prevent debris and spills from entering internal areas
• Restores the original look where a worn or missing plug detracts from the appliance finish
• Holds in place to protect underlying components from accidental contact
• Useful when replacing control bezels or trim that require a matching push-in cap

• Disconnect power to the appliance before performing any service work
• Press the plug button squarely into the opening until it snaps into place; no special tools typically required
• Inspect the mounting hole for damage or debris before installing to ensure a secure fit
• If the part does not seat properly, do not force it; verify correct part and orientation

Note: Quantity is one plug button.

Color: White

This stainless-steel refrigerator door replaces a damaged or dented outer door to restore appearance and proper sealing. It provides the exterior panel and mounting surfaces needed to secure door trim, handle, and gaskets. What it does:

• Replaces the outer fresh-food door panel so the fridge closes evenly and looks like new
• Restores the mounting surface for handles, trims, and door gaskets
• Helps stop air leaks caused by bent or dented doors, reducing moisture and temperature issues
• Addresses visible dents, scratches, corrosion, or cosmetic damage to the exterior

• One stainless-steel refrigerator outer door panel

• Disconnect power and empty door contents before removal to prevent tipping or injury
• Retain and transfer existing handle, trim, hinge hardware, and gasket unless replacements are supplied
• Inspect hinges and seals during installation; adjust alignment to ensure a proper door seal

This handle set is the OEM replacement door handle that restores a secure, comfortable grip for opening and appliance doors. It replaces worn, cracked, or broken handles to improve everyday use and appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, broken, or loose handles and helps eliminate wobble
• Restores original fit and appearance when the original handle is damaged
• Matches mounting points on the original door for a direct replacement

• Disconnect power and empty the door before starting work to avoid injury or damage
• Use the existing mounting screws and hardware; keep removed fasteners for reassembly
• Support the door while removing or installing the handle to prevent dropping or misalignment

This handle set is the OEM replacement door handle that restores a secure, comfortable grip for opening and appliance doors. It replaces worn, cracked, or broken handles to improve everyday use and appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, broken, or loose handles and helps eliminate wobble
• Restores original fit and appearance when the original handle is damaged
• Matches mounting points on the original door for a direct replacement

• Disconnect power and empty the door before starting work to avoid injury or damage
• Use the existing mounting screws and hardware; keep removed fasteners for reassembly
• Support the door while removing or installing the handle to prevent dropping or misalignment

This refrigerator door handle restores a secure, comfortable grip so you can open and close the door with confidence. Replace a cracked or loose handle to refresh your appliance's look and keep everyday use hassle-free.

• Provides the handhold used to open and close the refrigerator or freezer door
• Replaces cracked, broken, or missing handles
• Helps correct a loose or wobbly handle
• Can make the door easier to open when the old handle is damaged
• Restores the appliance's original appearance

• Unplug the refrigerator before servicing and wear cut-resistant gloves.
• Protect the door finish; remove any trim caps or set screws (as applicable) and detach the old handle.
• Align the new handle on the mounting studs and tighten screws evenly; do not overtighten.
• Verify the handle is secure and the door opens, closes, and seals properly.

The Door Handle is an OEM part for Frigidaire refrigerators. This part provides a secure grip for opening and closing the refrigerator door. This handle is essential for daily use, ensuring easy and convenient access to the refrigerator's contents.

Over time, the door handle can become worn out or damaged due to frequent use, mishandling, or accidental impacts.  

Symptoms of a bad door handle include:

• Looseness or wobbling when pulled
• Cracks or breaks in the handle material
• Difficulty in opening or closing the door
• The handle detaching from the door

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Handle is an OEM part for Frigidaire refrigerators. This component allows users to open and close the refrigerator door easily. It is designed to fit securely on the refrigerator door, providing a sturdy and comfortable grip. It is important to note that the necessary mounting screws are not included with the handle and must be gotten separately. 

Causes of a bad door handle can include wear and tear from frequent use, accidental impact, or damage during cleaning. The handle might also become loose or break if the screws or mounting points are compromised.

Symptoms of a bad door handle include:

• The handle feeling loose or wobbly
• Visible cracks or damage to the handle
• Difficulty in opening or closing the refrigerator door
• The handle detaching from the door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Handle is an OEM replacement part for Frigidaire refrigerators. It consists of the refrigerator door handle assembly, which allows for the opening and closing of the refrigerator door. 

Symptoms of a bad handle-door include:

• Loose, wobbly, or improperly installed door handle  
• Difficulty opening or closing the refrigerator door
• Damage or cracks in the door handle assembly
• The door not sealing properly when closed

Causes of a bad handle door can be normal wear and tear over time, accidental damage from impact, or overtightening of screws during installation. 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM part for Frigidaire appliances. This specific screw is designed for Frigidaire models, ensuring a secure fit and proper function in the appliance assembly. Screws like this one are critical for holding components together tightly, contributing to the overall stability and durability of the appliance. Whether used in refrigerators, ovens, washers, or dryers, this screw plays a pivotal role in assembly and maintenance tasks, ensuring parts remain securely fastened during operation.

Over time, screws can become loose, stripped, or lost during repairs or adjustments, potentially compromising the appliance's integrity and performance.  

Symptoms of needing replacement screws include:

• Loose parts or panels on the appliance
• Difficulty in securing components during assembly or maintenance
• The need to replace lost or damaged screws during repair work

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It is designed to facilitate the smooth opening and closing of the refrigerator door by providing a pivot point for the door hinge. This bearing ensures that the door moves easily and remains properly aligned, helping to maintain a tight seal and optimal refrigerator performance.

Causes of a bad hinge bearing can include regular wear and tear from frequent use, exposure to moisture or temperature changes, and physical damage due to accidental impacts. Over time, these factors can cause the hinge bearing to wear out, become loose, or break, affecting the door's functionality.

Symptoms of a bad hinge bearing include:

• Difficulty opening or closing the refrigerator door
• The door not staying in place or sagging
• Unusual noises, such as squeaking or grinding, when the door is moved
• The door not sealing properly, leading to temperature fluctuations inside the refrigerator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It plays a critical role in the smooth operation of the refrigerator door by providing a pivot point for the hinge. This small component helps to ensure that the door opens and closes smoothly and seals properly, which is essential for maintaining the refrigerator's internal temperature and energy efficiency.

Symptoms of a bad Hinge Bearing include:

• Difficulty in opening or closing the refrigerator door.
• Squeaking or grinding noises when the door moves.
• The door hanging unevenly or not sealing correctly, potentially leading to temperature fluctuations inside the fridge.

Causes of a bad hinge bearing can include wear and tear from the frequent use of the refrigerator door, accumulation of dirt or grime that impedes smooth movement, or degradation of the material over time due to environmental factors such as moisture.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Shelf Bin is an OEM replacement part for Frigidaire refrigerators. It is designed to fit on the refrigerator door, providing convenient storage space for condiments, bottles, and other small items. This shelf bin helps to keep the refrigerator organized, making it easier to find and reach items stored in the door. 

Causes of a bad door shelf bin can include cracking, breaking, or warping due to overloading, impact from items being moved in and out, or deterioration over time.

Symptoms of a bad door shelf bin include:

• Cracks or breakage in the bin.
• The bin not securely attaching to the door.
• Items falling out or not fitting properly in the bin.
• Difficulty in accessing or retrieving items from the bin.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Refrigerator Door Shelf is an OEM replacement part for Frigidaire refrigerators, designed to offer convenient storage space for jars, bottles, and other condiments within easy reach. Measures approximately 24 1/2 inches wide X 2 1/2 inches deep

Causes of a bad Refrigerator Door Shelf can include physical damage such as cracks or breaks from overloading it with too heavy items. Additionally, wear and tear over time can lead to the shelf becoming damaged.  

Symptoms of a bad Refrigerator Door Shelf include:

• Visible cracks or damage
• The shelf sagging or unable to retain items  
• Difficulty fitting the shelf into its designated slots  

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Refrigerator Door Shelf is an OEM replacement part for Frigidaire refrigerators, designed to offer additional storage space within the door of the appliance. This part provides a space for organizing items such as condiments, jars, and bottles, making them easily accessible while maximizing the interior storage of the refrigerator. Measures approximately 24 ¼ inches by 3 ¾  inches

Over time, the shelf can crack or break due to frequent use, overloading, or accidental impacts. A compromised door shelf can lead to instability and difficulty in securely holding items.

Symptoms of a bad Refrigerator Door Shelf include:

• Cracks or visible damage to the shelf
• Difficulty attaching the shelf to the door
• Items falling out or not staying in place
• Reduced storage capacity on the door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Freezer Door Shelf Bin is an OEM replacement part for Frigidaire refrigerators. It provides adjustable storage on the inside of the freezer door with removable bin shelves. These bins maximize storage potential in the limited door space through customizable shelving.

Causes of a bad Door Shelf Bin can include shelf breakage from heavy loads, damage to supporting rails or walls of the bin inhibiting proper shelf attachment and use, or broken/missing bin walls reducing structural integrity.

Symptoms of a bad Door Shelf Bin include:

• Detached or missing shelves
• Shelves that do not stay firmly in place when loaded
• Damage or deterioration of bin walls
• Insufficient or compromised storage space

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Door Handle Mounting Block is an OEM part for Frigidaire refrigerators. This component secures the door handle to the refrigerator door, ensuring it remains firmly attached and easy to use.

Causes of a bad mounting block can include repeated use leading to wear and tear, accidental damage, or improper installation that causes it to loosen or break.

Symptoms of a bad door handle mounting block include:

• The door handle feeling loose or wobbly
• Difficulty in opening or closing the refrigerator door
• The door handle detaching from the door
• Visible cracks or damage to the mounting block

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a service wrench used to loosen and tighten appliance fasteners for maintenance and repairs, making access and part replacement easier for technicians and DIYers. Durable tool designed for specific appliance fastener sizes. What it does:

• Provides the correct fit and leverage for removing or installing designated appliance nuts, bolts, and fittings
• Helps safely access internal components during service and part replacement
• Reduces risk of rounding fasteners compared with improvised tools
• Useful for routine maintenance tasks and repair procedures that require a dedicated wrench

• One wrench

• Use the wrench only for its intended appliance fasteners; avoid excessive force
• Disconnect power and water to the appliance before beginning service
• Wear safety gloves and eye protection when working on appliances