Parts for Maytag MGDE400XW1: 05 - Door Parts

This is a small adhesive label or cover designed to conceal unused hinge mounting holes on the appliance door, providing a clean finished appearance. It is white in color and covers the hole left when the door hinge is installed on the opposite side. Replace if the cover is peeling, missing, or discolored, leaving an exposed hole on the door surface.

Connects dryer door to cabinet, allowing smooth opening and closing. Replace if hinge is broken, worn, bent, or causing door misalignment issues.

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

Retainer link that secures cables in your dryer. Installs to hold wiring harnesses in place. Replace if cracked, broken, or missing to restore proper fit.

Secures dryer components in place to prevent movement and maintain proper alignment. Replace if your retainer clip is cracked, broken, or missing.

This replacement screw secures appliance components as designed by the manufacturer. Installing a new fastener restores a tight fit when the original is missing, stripped, or corroded, helping prevent vibration and misalignment during use.

• Fastens brackets, panels, or assemblies in the specified locations
• Replaces missing, stripped, or rusted hardware
• Helps maintain proper alignment and reduce vibration/noise
• Common signs you need this part: loose components, rattling, or a screw that won't tighten

• Disconnect power and turn off water supply before servicing
• Match the screw to its original location; length and thread engagement
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse any original washers or spacers that were installed with the screw

This replacement plug seals a drain or access opening to prevent leaks and keep refrigerant/condensate and debris where they belong. Fits service openings on compatible Whirlpool appliances to restore a watertight seal. What it does:

• Seals a drain, access hole, or service opening to stop water or debris from leaking out
• Helps maintain proper condensate routing and prevents pooling inside the cabinet
• Prevents pests and dust from entering through unused openings
• Simple, non-electrical part that restores the original seal and function

• One plug

• Disconnect power to the appliance before servicing; follow all safety procedures
• Press the plug firmly into the opening until fully seated; use hand pressure only unless otherwise specified
• Inspect for proper sealing and test with a small water flow before reassembling the appliance

Replace stripped or missing screws causing loose panels or rattling during cycles. This self-locking Phillips screw secures internal components. Easy 5-minute fix.

This is a tempered glass window assembly that fits into the dryer door, allowing you to see the drum and laundry during the drying cycle. It is mounted within the door panel and secured by a retaining frame. Replace this assembly if the glass is cracked, shattered, or if the seal around the window is damaged, which can allow heat to escape and reduce drying efficiency.

Replace your worn dryer door seal to prevent air leaks and maintain efficient drying. This rubber gasket creates a tight barrier around the door opening. Confirm fit with your model number before ordering.

Sheet metal screw secures panels, brackets, and trim on washers, dryers, and laundry appliances. Replace when stripped, missing, or rusted during repair.

Replace your worn dryer door seal to restore a tight closure, contain heat and moisture, and eliminate rattling or squeaking. Easy snap-in install.

This is a protective shield that mounts along the edge of the dishwasher door. It helps prevent steam and moisture from escaping the door and damaging the surrounding cabinetry or countertop. Replace this shield if it is warped, cracked, or missing, or if you notice moisture damage around the dishwasher door area.

The Door Latch Kit is an OEM replacement part for Whirlpool washers. This component is responsible for securely locking the washer door during the wash cycle, preventing it from opening unexpectedly and ensuring a safe and efficient operation.

Symptoms of needing to replace the door latch kit include:

• Difficulty in closing or latching the washer door
• Door opening unexpectedly during the wash cycle
• Leaks or water seeping due to an improper door seal
• Excessive wear or damage to the latch components

Causes of a faulty door latch kit can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the door alignment or strike plate.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.