Parts for Kenmore 106.8614320 (1068614320, 106 8614320): Door Parts

This freezer door gasket forms an airtight seal between the door and cabinet to keep cold air in and humid air out. Replacing a worn gasket helps maintain temperature, reduce frost, and improve efficiency. What it does:

• Seals the perimeter of the freezer door to prevent air leaks
• Helps maintain stable freezer temperature and proper freezing performance
• Reduces warm air infiltration that leads to frost and moisture
• Common symptoms of a failing gasket: tears or warping, frost along door edges, condensation around the door, poor sealing or door popping open, longer run times

• 1 freezer door gasket

• Disconnect power before servicing; open the door and clear the work area
• Warm the new gasket in hot water or with low heat to relax folds; clean the sealing surfaces
• If your model uses a screw-on retainer, loosen screws to remove the old gasket and install the new one evenly; if it press-fits, seat the gasket lip fully into the channel, aligning corners
• After installation, verify an even seal all around; adjust hinges/leveling if needed and use low heat to smooth waves; test with a dollar-bill test

This part has been discontinued and is no longer available.

This refrigerator door gasket seals the fresh food compartment door to restore an airtight closure. A proper seal helps keep cold air in, limit moisture intrusion, and support stable temperatures and efficiency.

• Creates a tight seal between the fresh food door and cabinet
• Helps maintain interior temperature and reduce energy loss
• Limits condensation and frost near the door opening
• Worn, torn, or misshapen gaskets may cause warm spots, sweating, or doors that won't close fully

• Unplug the refrigerator before servicing.
• Pull the inner lip from the door retainer to remove; some models require loosening liner screws hidden under the gasket edge.
• Warm the new gasket (warm water or gentle heat) to relax folds, then press the lip fully into the channel.
• Close the door and check for uniform contact; adjust hinges or re-tighten liner screws as needed.

This part has been discontinued and is no longer available.

This replacement screw secures panels, brackets, and other components in your appliance so they stay tight and properly aligned. Use it to replace missing, stripped, or rusted hardware and eliminate looseness, rattles, or gaps.

• Fastens parts to the cabinet/frame to maintain structural integrity
• Helps keep panels and assemblies aligned to reduce vibration and noise
• Replaces missing, damaged, or corroded screws during service
• Common fix for loose panels or components that no longer hold securely

• Disconnect power and shut off water or gas before servicing
• Match length and thread to the original screw for proper fit
• Hand-start threads to avoid cross-threading; tighten only until snug—do not overtighten
• Tighten them evenly to ensure proper alignment

This part has been discontinued by the manufacturer and is no longer available.

This screw cover conceals the mounting screw at the end of the door handle, restoring a clean, finished look while protecting the fastener. Replace a missing or damaged cap to keep the handle hardware covered and secure.

• Covers the exposed handle screw for a finished appearance
• Helps shield the screw head from dirt and moisture
• Direct replacement for a cracked, broken, loose, or missing cap
• Common signs: visible screw, cap won't stay in place, or cosmetic damage

• Use a plastic pry tool to remove the old cover without scratching nearby surfaces
• Verify the handle screw is properly seated; adjust/tighten as needed before installing the cover
• Align the new cover with the opening and press until it snaps flush
• Avoid overtightening the handle screw; excessive torque can prevent the cover from seating

This sheet-metal screw secures appliance panels, brackets, and components to the cabinet. Replacing a missing or stripped fastener restores a tight, rattle-free fit and helps keep assemblies aligned for reliable operation.

• Fastens sheet-metal parts to the chassis or support brackets
• Replaces stripped, corroded, or lost screws to restore proper hold
• Helps reduce vibration and noise from loose panels
• Maintains alignment of covers, ducts, or trim

• Disconnect power to the appliance; shut off water or gas if applicable.
• Match this screw to the original location and length.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• If the original hole is damaged, repair or replace the mounting point before installing.

This part has been discontinued by the manufacturer and is no longer available.

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part has been discontinued by the manufacturer and is no longer available.

This sheet-metal screw secures appliance panels, brackets, and components to the cabinet. Replacing a missing or stripped fastener restores a tight, rattle-free fit and helps keep assemblies aligned for reliable operation.

• Fastens sheet-metal parts to the chassis or support brackets
• Replaces stripped, corroded, or lost screws to restore proper hold
• Helps reduce vibration and noise from loose panels
• Maintains alignment of covers, ducts, or trim

• Disconnect power to the appliance; shut off water or gas if applicable.
• Match this screw to the original location and length.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• If the original hole is damaged, repair or replace the mounting point before installing.

Epoxy repair kit - aluminum tubing.