Parts for Electrolux EW30MC65JB2: 09 - Doors Parts

This deflector directs internal airflow to help maintain consistent temperatures and proper circulation inside the appliance. It replaces a damaged or missing deflector to restore intended airflow routing and component protection. What it does:

• Guides and redirects air to improve temperature balance and performance
• Helps prevent localized freezing or warm spots caused by disrupted airflow
• Protects nearby components from direct airflow and debris
• Restores proper airflow path after cracks, breaks, or dislodgement

• Disconnect power and remove any food or loose items from the area before starting
• Handle the deflector carefully to avoid cracking; align tabs/slots and snap or secure in place per OEM layout
• Use basic hand tools only; avoid forcing parts to prevent damage

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This heat-resistant insulation helps contain oven heat and shield surrounding components. Replacing worn insulation supports faster, more consistent preheating, steadier baking temperatures, and cooler exterior panels for safer, more efficient operation. What it does:

• Wraps/lines the oven cavity or panels to reduce heat loss and protect nearby wiring and controls
• Helps the oven preheat efficiently and maintain consistent cooking temperatures
• Limits heat transfer to exterior panels and surrounding cabinetry
• Common signs of failure: longer preheat times, temperature swings, unusually hot sides/back, or insulation that is burnt, brittle, soaked, or missing

• 1 insulation piece

• Disconnect power and, if applicable, shut off gas before servicing
• Access typically requires removing rear/side panels or sliding the unit out; take photos to aid reassembly
• Wear gloves and a dust mask; handle gently—do not compress insulation and keep clear of sensors/wiring
• Re-secure with original clips/tape, reinstall panels, then test preheat and check for abnormal exterior heat

The Inner Door Glass is an  OEM replacement part for Frigidaire ranges. It is responsible for providing a safe viewing window into the oven cavity while protecting interior components from external damage.  

Causes of a bad inner door glass include normal wear and tear such as chips or cracks developing from years of use. Accidental impact or thermal shocks from sudden temperature changes can also compromise the integrity of the glass.

Symptoms of a bad inner door glass:

• Cracks or breaks visible in the glass
• Difficulty seeing into the oven cavity clearly 
• Increased risk of heat escaping when the oven is in use
• Potential safety hazards if glass cracks or shatters  

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

This oven door gasket creates a tight seal between the door and the oven frame to hold in heat and help maintain consistent cooking temperatures. Replacing a worn seal can improve preheat times and reduce heat loss and spills from escaping.

• Seals the oven door perimeter to minimize heat and moisture loss
• Helps the oven reach and maintain set temperatures more reliably
• Can address issues like longer preheat, uneven baking, or heat escaping around the door
• Replaces gaskets that are torn, flattened, frayed, or brittle

• Disconnect power and allow the oven to cool completely before service
• Open the door and carefully remove the old gasket from its clips or channel
• Clean the sealing surfaces to remove debris and residue
• Seat the new gasket evenly around the perimeter without stretching or twisting

This replacement frame restores the appliance's front cabinet trim for a finished look and secure component fit. It helps protect internal parts and keeps the control area or door edges properly aligned. What it does:

• Replaces damaged, cracked, or warped front trim that affects appearance or fit
• Secures adjacent panels and provides a mounting surface for controls or seals
• Helps stop drafts or gaps that can form around doors or control openings
• Restores proper alignment to reduce rubbing or interference with moving parts

• One replacement frame as pictured

• Disconnect power (unplug or switch off breaker) before starting any repair
• Basic hand tools (screwdriver, nut driver) are typically required; keep fasteners for reuse if intact
• Handle edges carefully to avoid scratching the finish; protect surrounding surfaces during installation

This right-side latch head is part of the door latching assembly. Replacing a worn or broken latch head restores positive door engagement so the appliance recognizes a closed door and operates safely and reliably.

• Engages the door strike to keep the door closed and actuate safety/interlock switches
• Helps address "door open" messages, won't start conditions, or doors that pop open
• Replaces cracked, worn, or missing right-side latch head that causes loose latching
• Side-specific component; left and right are not interchangeable

• Disconnect power before servicing; be aware high-voltage capacitors can retain a dangerous charge
• Remove the door/inner trim as needed to access the latch mechanism
• Note spring/linkage orientation and transfer to the new latch head
• After reassembly, verify smooth door closure and proper operation before restoring power

This left-side door latch head is the hook assembly on the microwave door that engages the interlock switches. Replacing a worn latch restores a secure close and reliable start/stop so the unit operates only with the door fully shut. What it does:

• Hooks into the cabinet to keep the door closed and aligned
• Actuates the door interlock switches for safe operation
• Helps prevent doors from popping open or needing pressure to run

• Includes 1 left-side latch head

• Disconnect power at the breaker before servicing
• Remove the inner door trim to access the latch; support the door and protect the glass
• Compare orientation and transfer any reusable hardware from the original part
• After reassembly, verify the door closes smoothly and the microwave only starts with the door fully closed

This replacement tension spring restores proper tension to the appliance's moving mechanism so doors, latches or linkages operate smoothly and reliably. It's a simple wearable part that helps fix sagging or loose motion. What it does:

• Provides tension for a door, latch or linkage to return to the correct position
• Helps stop door sag, uneven closing or loose movement
• Eliminates slack that can cause rattling or noisy operation
• Restores proper alignment so mechanical interlocks engage

• One tension spring

• Disconnect power and/or supply (unplug or shut off circuit) before starting
• Release stored tension carefully—use proper tools and eye protection
• Inspect mating parts (pins, clips, brackets) and replace if worn

This is a replacement mounting screw used to secure panels, trim, and small components in compatible appliances. Installing the correct screw restores a secure fit and helps stop rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces or small assemblies to the appliance frame
• Prevents parts from shifting, vibrating, or producing rattling noises when in place
• Replaces missing, worn, or stripped fasteners that cause loose doors or misaligned trim
• Works with the original mounting points and thread types used by the manufacturer

• Always disconnect power or unplug the appliance before servicing to avoid electrical hazard.
• Use the correct screwdriver or bit to avoid stripping the head; do not overtighten.
• Keep track of small parts and compare the new screw to the old one before installation.

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.