Parts for Frigidaire FGET2765PFC: 09 - Doors Parts

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This is a replacement glass panel for the appliance assembly. It restores a clear, intact barrier where the original glass was cracked, chipped, or missing—helping the unit operate safely and look like new. What it does:

• Replaces broken or shattered glass to restore the intended barrier or support surface
• Helps maintain safe operation by eliminating sharp edges and gaps
• Preserves proper appearance and fit of the assembly
• Typical symptoms: visible cracks, spider-web shatter, loose or rattling panel, missing glass

• One glass panel

• Disconnect power and allow all surfaces to cool before service; wear cut-resistant gloves and eye protection
• Support the assembly during disassembly to prevent drops or stress on hinges/frames
• Transfer any trim, brackets, gaskets, or insulation from the original panel as required
• Handle glass carefully by the edges; do not overtighten fasteners against glass

This inner cabinet liner replaces a worn, cracked, or damaged refrigerator cabinet surface to restore a clean, sealed interior and prevent moisture damage. It provides the structural surface that supports shelves and seals the cooling cavity. What it does:

• Restores the refrigerator's interior surface when the original liner is cracked, warped, or stained
• Helps maintain proper airflow and preserves the cabinet seal around shelves and gaskets
• Prevents food and liquid from contacting the cabinet cavity behind the liner
• Reduces drafts and cold spots caused by damaged interior surfaces

• Designed to be installed by an experienced DIYer; follow the refrigerator's service manual
• Requires removal of shelves, trim, and door(s) for access; keep hardware organized for reassembly
• Inspect and replace any damaged fasteners, insulation, or seal components as needed for a complete repair
• Disconnect power and empty the unit before beginning work to prevent injury or damage

This is a replacement mounting screw used to secure panels and components in compatible Frigidaire appliances. It restores proper fit and helps prevent rattles, loose panels, and parts that shift during operation. What it does:

• Fastens trim, panels, brackets, or controls to the appliance frame
• Restores secure attachment to reduce vibration, noise, and movement
• Replaces stripped, missing, or corroded screws that prevent proper assembly
• Works wherever the OEM screw with this part number is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging parts
• Keep removed hardware organized and compare parts to the old screw for correct fit

This is a full outer refrigerator door assembly that restores the cabinet seal, appearance, and normal door operation. It replaces a damaged, dented, or warped outer door to help maintain proper cooling and appearance. What it does

• Replaces the refrigerator outer door panel and attached trim so the door closes evenly and seals properly
• Restores cosmetic finish and trim that may be dented, cracked, or gouged
• Helps reduce air leaks that can cause temperature issues or increased run time
• Replaces components that prevent rattling or uneven door alignment during normal use

• One outer refrigerator door assembly

• Installation requires removing the old door from its hinges; support the door to avoid dropping or damaging the cabinet
• Use basic hand tools; follow the appliance's service manual for hinge and wiring handling if applicable
• Disconnect power to the appliance before attempting any removal or repair
• If the door has wiring for a dispenser or lights, connectors are secured and routed per the service instructions

This is a full outer refrigerator door assembly that restores the cabinet seal, appearance, and normal door operation. It replaces a damaged, dented, or warped outer door to help maintain proper cooling and appearance. What it does

• Replaces the refrigerator outer door panel and attached trim so the door closes evenly and seals properly
• Restores cosmetic finish and trim that may be dented, cracked, or gouged
• Helps reduce air leaks that can cause temperature issues or increased run time
• Replaces components that prevent rattling or uneven door alignment during normal use

• One outer refrigerator door assembly

• Installation requires removing the old door from its hinges; support the door to avoid dropping or damaging the cabinet
• Use basic hand tools; follow the appliance's service manual for hinge and wiring handling if applicable
• Disconnect power to the appliance before attempting any removal or repair
• If the door has wiring for a dispenser or lights, connectors are secured and routed per the service instructions

This spring-loaded hinge supports and controls the oven door's movement so it opens smoothly and closes firmly, helping the door seal properly and retain heat. Replacing a worn hinge restores proper door alignment and closing force.

• Provides the pivot and spring tension for controlled door opening/closing
• Helps the door sit flush against the gasket to maintain a proper heat seal
• Common symptoms: door won't fully close, sags or drops, won't hold at a mid-open position, heat escaping from the front
• Typical causes of failure: metal fatigue, spring wear, or hinge deformation from heavy use

• Disconnect power; for gas models, also shut off gas. Allow the oven to cool completely.
• Support the door and engage hinge locks or remove the door.
• Springs are under tension—use gloves and eye protection; do not disassemble the hinge.
• Align with the receivers/slots and test for smooth operation and full closure; consider replacing both for even tension.

This replacement door handle provides a secure grip to open and close your refrigerator door, restoring normal door operation and improving appearance. Designed as a direct-fit OEM-style handle for quick replacement. What it does:

• Replaces a cracked, broken or loose refrigerator door handle so the door can be opened and closed safely.
• Restores a comfortable grip and proper leverage for everyday use.
• Helps prevent further cabinet or door damage caused by makeshift grips or tape.
• Works with the door latch and hinge assembly to maintain normal door function.

• Disconnect power and empty door shelves before starting to avoid items falling.
• Remove mounting screws and/or trim as required; install handle in the original orientation.
• Tighten fasteners securely but avoid over-torquing to prevent cracking the handle.

This support bracket secures and stabilizes appliance components, restoring proper alignment and stopping movement. It's a simple replacement that helps reduce rattling and prevents panels or assemblies from shifting during use. What it does:

• Provides a rigid mounting point to hold panels, trim, or internal assemblies in place
• Restores proper alignment when a worn or broken bracket causes gaps or looseness
• Reduces vibration and rattling caused by a damaged or missing support
• Keeps connected parts from shifting, which can prevent further wear or damage

• Disconnect power to the appliance before beginning any repair
• Verify the bracket orientation and fit against the mating surface before fastening
• Use the factory screw locations and hardware; tighten screws securely but avoid over-torquing

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

Specs: 8 - 18 x 0.500

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts