Parts for Frigidaire FGMC2765PBB: 09 - Doors Parts

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This is a replacement glass panel for the appliance assembly. It restores a clear, intact barrier where the original glass was cracked, chipped, or missing—helping the unit operate safely and look like new. What it does:

• Replaces broken or shattered glass to restore the intended barrier or support surface
• Helps maintain safe operation by eliminating sharp edges and gaps
• Preserves proper appearance and fit of the assembly
• Typical symptoms: visible cracks, spider-web shatter, loose or rattling panel, missing glass

• One glass panel

• Disconnect power and allow all surfaces to cool before service; wear cut-resistant gloves and eye protection
• Support the assembly during disassembly to prevent drops or stress on hinges/frames
• Transfer any trim, brackets, gaskets, or insulation from the original panel as required
• Handle glass carefully by the edges; do not overtighten fasteners against glass

This spring-loaded hinge supports and controls the oven door's movement so it opens smoothly and closes firmly, helping the door seal properly and retain heat. Replacing a worn hinge restores proper door alignment and closing force.

• Provides the pivot and spring tension for controlled door opening/closing
• Helps the door sit flush against the gasket to maintain a proper heat seal
• Common symptoms: door won't fully close, sags or drops, won't hold at a mid-open position, heat escaping from the front
• Typical causes of failure: metal fatigue, spring wear, or hinge deformation from heavy use

• Disconnect power; for gas models, also shut off gas. Allow the oven to cool completely.
• Support the door and engage hinge locks or remove the door.
• Springs are under tension—use gloves and eye protection; do not disassemble the hinge.
• Align with the receivers/slots and test for smooth operation and full closure; consider replacing both for even tension.

A small mounting spacer used to position and support appliance components for correct alignment and stable operation. Replaces a worn or missing spacer to help restore proper fit between panels and parts. What it does:

• Keeps panels, brackets, or components spaced correctly to prevent rubbing and misalignment
• Helps reduce vibration and rattling caused by gaps or loose fits
• Restores correct clearance for moving parts that need precise spacing
• Used wherever a fixed gap or support is required between parts

• Disconnect power (and fuel or water if applicable) before beginning any repair
• Access may require removing outer panels, trim, or adjoining components
• Keep orientation and placement the same as the original spacer; install snugly but avoid over-tightening
• If other parts show wear or damage, inspect and replace them as needed for a complete repair

This replacement frame restores the appliance's front trim and structural support where the cabinet meets the control or door area, improving appearance and panel alignment. It's a direct-fit exterior trim piece designed for a clean, finished look. What it does:

• Replaces cracked, warped, or broken front trim that affects appearance
• Supports and aligns adjacent panels, doors, or control bezels
• Helps prevent gaps where dirt or moisture can collect
• Restores a secure mounting surface for attached components

• One replacement frame piece as pictured

• Disconnect power to the appliance before starting any repair
• Minor disassembly of surrounding panels may be required; keep fasteners organized
• Use appropriate hand tools and avoid overtightening to prevent cracking

This door latch hook secures the refrigerator door latch so the door closes and seals correctly. Replacing a broken or worn hook restores reliable door latching and helps prevent temperature loss from an improperly closed door. What it does:

• Secures the door latch assembly so the refrigerator door stays closed.
• Restores proper latch engagement to help maintain the door seal and consistent cooling when the door was not closing fully.
• Can address symptoms such as a door that won't latch, door popping open, or visible damage to the hook.
• Direct replacement for the factory latch hook to restore proper fit and function.

• Disconnect power to the appliance before starting any repair.
• Remove door trim or inner liner as needed to access the latch; keep all screws and fasteners for reassembly.
• Verify latch alignment and striker position before tightening; hand-tighten first and avoid over-tightening.

This door latch spring restores the return tension in your microwave's door release mechanism so the latch engages and releases correctly. Replacing a fatigued or broken spring helps ensure safe door operation and reliable interlock switch activation.

• Provides the return force for the latch lever/door release button
• Helps door hooks engage fully and release smoothly
• Supports proper interlock switch actuation so the unit will run only when the door is closed
• Typical failure signs: door won't latch, "open/close door" error, door button sticks, or needing to hold the door shut to start

• Disconnect power. Microwaves can retain dangerous high voltage even when unplugged; discharge the capacitor
• Access the latch assembly behind the control panel; note the spring's orientation and attachment points
• Use needle-nose pliers to install without overstretching; inspect the latch lever and door hooks for wear
• Verify proper door closure and interlock switch operation before reassembly

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts