Parts for Frigidaire FGMC2765PFB: 09 - Doors Parts

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This is a replacement glass panel for the appliance assembly. It restores a clear, intact barrier where the original glass was cracked, chipped, or missing—helping the unit operate safely and look like new. What it does:

• Replaces broken or shattered glass to restore the intended barrier or support surface
• Helps maintain safe operation by eliminating sharp edges and gaps
• Preserves proper appearance and fit of the assembly
• Typical symptoms: visible cracks, spider-web shatter, loose or rattling panel, missing glass

• One glass panel

• Disconnect power and allow all surfaces to cool before service; wear cut-resistant gloves and eye protection
• Support the assembly during disassembly to prevent drops or stress on hinges/frames
• Transfer any trim, brackets, gaskets, or insulation from the original panel as required
• Handle glass carefully by the edges; do not overtighten fasteners against glass

This inner cabinet liner replaces a worn, cracked, or damaged refrigerator cabinet surface to restore a clean, sealed interior and prevent moisture damage. It provides the structural surface that supports shelves and seals the cooling cavity. What it does:

• Restores the refrigerator's interior surface when the original liner is cracked, warped, or stained
• Helps maintain proper airflow and preserves the cabinet seal around shelves and gaskets
• Prevents food and liquid from contacting the cabinet cavity behind the liner
• Reduces drafts and cold spots caused by damaged interior surfaces

• Designed to be installed by an experienced DIYer; follow the refrigerator's service manual
• Requires removal of shelves, trim, and door(s) for access; keep hardware organized for reassembly
• Inspect and replace any damaged fasteners, insulation, or seal components as needed for a complete repair
• Disconnect power and empty the unit before beginning work to prevent injury or damage

This replacement 10-24 x 3/8 machine screw secures panels, brackets, and small components in compatible Frigidaire appliances. It restores proper fastening where a missing or damaged screw allows parts to shift or rattle. What it does:

• Fastens metal or plastic appliance parts such as trim, brackets, or small assemblies
• Helps eliminate movement, rattling, or loose connections caused by missing or stripped screws
• Restores safe, secure mounting for controls and hardware
• Matches OEM size for proper fit in designated threaded holes

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or nut driver to avoid stripping the head
• Start threads by hand to ensure alignment; tighten until snug — do not over-tighten
• Replace any stripped mating hardware or use correct thread engagement for secure fit

This spring-loaded hinge supports and controls the oven door's movement so it opens smoothly and closes firmly, helping the door seal properly and retain heat. Replacing a worn hinge restores proper door alignment and closing force.

• Provides the pivot and spring tension for controlled door opening/closing
• Helps the door sit flush against the gasket to maintain a proper heat seal
• Common symptoms: door won't fully close, sags or drops, won't hold at a mid-open position, heat escaping from the front
• Typical causes of failure: metal fatigue, spring wear, or hinge deformation from heavy use

• Disconnect power; for gas models, also shut off gas. Allow the oven to cool completely.
• Support the door and engage hinge locks or remove the door.
• Springs are under tension—use gloves and eye protection; do not disassemble the hinge.
• Align with the receivers/slots and test for smooth operation and full closure; consider replacing both for even tension.

This replacement frame restores the appliance's front trim and structural support where the cabinet meets the control or door area, improving appearance and panel alignment. It's a direct-fit exterior trim piece designed for a clean, finished look. What it does:

• Replaces cracked, warped, or broken front trim that affects appearance
• Supports and aligns adjacent panels, doors, or control bezels
• Helps prevent gaps where dirt or moisture can collect
• Restores a secure mounting surface for attached components

• One replacement frame piece as pictured

• Disconnect power to the appliance before starting any repair
• Minor disassembly of surrounding panels may be required; keep fasteners organized
• Use appropriate hand tools and avoid overtightening to prevent cracking

The Door Assembly is an OEM part for Frigidaire microwaves. This complete assembly includes the door panel, handle, seals, and glass, ensuring that your microwave maintains its functionality and safety standards.  

Causes of a bad door assembly can include mechanical stress from frequent opening and closing, accidental impacts, or degradation of materials over time due to exposure to high temperatures and frequent cleaning.

Symptoms of a bad door assembly include:

• The door not sealing properly, which can lead to heat loss and inefficient cooking
• Cracks or damage to the door panel or glass
• Issues with the door latch that prevent it from closing securely
• Noticeable wear or deformation of the seal, which could potentially lead to microwave leakage

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door latch hook secures the refrigerator door latch so the door closes and seals correctly. Replacing a broken or worn hook restores reliable door latching and helps prevent temperature loss from an improperly closed door. What it does:

• Secures the door latch assembly so the refrigerator door stays closed.
• Restores proper latch engagement to help maintain the door seal and consistent cooling when the door was not closing fully.
• Can address symptoms such as a door that won't latch, door popping open, or visible damage to the hook.
• Direct replacement for the factory latch hook to restore proper fit and function.

• Disconnect power to the appliance before starting any repair.
• Remove door trim or inner liner as needed to access the latch; keep all screws and fasteners for reassembly.
• Verify latch alignment and striker position before tightening; hand-tighten first and avoid over-tightening.

This door latch spring restores the return tension in your microwave's door release mechanism so the latch engages and releases correctly. Replacing a fatigued or broken spring helps ensure safe door operation and reliable interlock switch activation.

• Provides the return force for the latch lever/door release button
• Helps door hooks engage fully and release smoothly
• Supports proper interlock switch actuation so the unit will run only when the door is closed
• Typical failure signs: door won't latch, "open/close door" error, door button sticks, or needing to hold the door shut to start

• Disconnect power. Microwaves can retain dangerous high voltage even when unplugged; discharge the capacitor
• Access the latch assembly behind the control panel; note the spring's orientation and attachment points
• Use needle-nose pliers to install without overstretching; inspect the latch lever and door hooks for wear
• Verify proper door closure and interlock switch operation before reassembly

This replacement door handle provides a secure grip to open and close your refrigerator door, restoring normal door operation and improving appearance. Designed as a direct-fit OEM-style handle for quick replacement. What it does:

• Replaces a cracked, broken or loose refrigerator door handle so the door can be opened and closed safely.
• Restores a comfortable grip and proper leverage for everyday use.
• Helps prevent further cabinet or door damage caused by makeshift grips or tape.
• Works with the door latch and hinge assembly to maintain normal door function.

• Disconnect power and empty door shelves before starting to avoid items falling.
• Remove mounting screws and/or trim as required; install handle in the original orientation.
• Tighten fasteners securely but avoid over-torquing to prevent cracking the handle.

This support bracket secures and stabilizes appliance components, restoring proper alignment and stopping movement. It's a simple replacement that helps reduce rattling and prevents panels or assemblies from shifting during use. What it does:

• Provides a rigid mounting point to hold panels, trim, or internal assemblies in place
• Restores proper alignment when a worn or broken bracket causes gaps or looseness
• Reduces vibration and rattling caused by a damaged or missing support
• Keeps connected parts from shifting, which can prevent further wear or damage

• Disconnect power to the appliance before beginning any repair
• Verify the bracket orientation and fit against the mating surface before fastening
• Use the factory screw locations and hardware; tighten screws securely but avoid over-torquing

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

Specs: 8 - 18 x 0.500

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts