Parts for Frigidaire WRTS23V7MW2: Doors Parts

This freezer door gasket creates a tight seal around the door to keep cold air in and humid air out—helping maintain set temperatures, reduce frost buildup, and support efficient, reliable freezer performance. What it does:

• Seals the freezer door perimeter to prevent air leaks and warm air infiltration
• Helps maintain consistent freezer temperature and energy efficiency
• Helps reduce frost/ice buildup and condensation around the door
• A worn, torn, or warped gasket can lead to poor sealing, frost, moisture, or longer run times

• 1 freezer door gasket

• Disconnect power before servicing
• Allow the new gasket to warm and relax (room temperature or warm water) for easier installation; do not overheat
• Remove the old gasket; clean and dry the door channel, then press the new gasket fully into place, starting at the corners
• After installation, check for uniform contact all around; adjust the door/hinges if needed and verify with a paper-slip test

The Refrigerator Door Gasket is an OEM part for Frigidaire refrigerators, designed to seal the door of the refrigerator compartment, ensuring an airtight closure. This door gasket plays a crucial role in maintaining the efficiency of the refrigerator by preventing cold air from escaping and warm air from entering.

Common causes for a Refrigerator Door Gasket to fail include normal wear and tear from opening and closing the door, damage from cleaning or misuse, and aging of the material, which can lead to hardening and loss of elasticity.

Symptoms of a bad Refrigerator Door Gasket include:

• Noticeable gaps or tears in the gasket
• The refrigerator door does not close as tightly as it should, or it requires more force to close.
• Condensation or frost buildup around the door edges
• An increase in energy consumption

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Dairy Door is an OEM replacement part for Frigidaire side-by-side refrigerators. As the access point to the dedicated dairy compartment, the door is designed with precision seals to maintain optimal humidity levels inside. This helps keep dairy and other perishable items fresh longer.

Causes of a bad dairy door can include worn or damaged seals, dents or impacts warping the door frame, or issues with the electronic components that control humidity levels.

Symptoms of a bad dairy door include: 

• Excessive frost or ice buildup inside the dairy compartment   
• Difficulty opening and closing the door smoothly  
• Warm or dried-out dairy products despite a cold refrigerator interior
• Moisture leaks around the door seals  

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore side-by-side models.

Color: White. Used to cover the hinge bearing hole.

This door stop limits the refrigerator door's opening range to protect hinges and nearby cabinets. Replace a cracked or missing stop to restore smooth, controlled door movement and help the door close and seal properly.

• Limits door swing to prevent overextension and impact with walls or cabinets
• Reduces hinge stress and helps maintain proper door alignment
• Common signs of failure: door opens too far, binds at the hinge, or the original stop is cracked/missing
• Restores smooth, controlled door motion and closure

• Disconnect power and remove items from the door to reduce weight
• Support the door before loosening any hinge fasteners
• Install the new stop in the correct orientation for your model
• Adjust hinges if needed

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

Color: White

This refrigerator door handle restores a secure, comfortable grip for opening and closing the door. Replace a cracked, loose, or broken handle to refresh your appliance's look and ensure proper leverage with each use.

• Attaches to the door to provide a firm handhold
• Helps ensure smooth opening/closing by providing proper leverage
• Replace if the handle is cracked, broken, loose, or missing
• Wobbling or difficulty gripping the door are common signs it needs replacement

• Unplug the refrigerator before beginning any repair
• Remove the old handle's mounting screws; retain screws and any decorative caps for reuse
• Align the new handle, start all screws by hand, then tighten evenly—do not overtighten
• The door opens/closes smoothly and the gasket seals properly after installation

This replacement screw secures select refrigerator door handles to the door. A worn or missing screw can leave the handle loose or detached, making the door difficult to open and potentially stressing other components.

• Holds the door handle firmly to the door
• Helps restore proper door operation and safe grip
• Designed to fit designated mounting points for compatible models

• Unplug the refrigerator before beginning work
• Open the door to access the handle mounting points
• Use the correct screwdriver/Allen tool to avoid stripping the head
• Start threads by hand and tighten snugly—do not overtighten

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM part for Frigidaire appliances. This specific screw is designed for Frigidaire models, ensuring a secure fit and proper function in the appliance assembly. Screws like this one are critical for holding components together tightly, contributing to the overall stability and durability of the appliance. Whether used in refrigerators, ovens, washers, or dryers, this screw plays a pivotal role in assembly and maintenance tasks, ensuring parts remain securely fastened during operation.

Over time, screws can become loose, stripped, or lost during repairs or adjustments, potentially compromising the appliance's integrity and performance.  

Symptoms of needing replacement screws include:

• Loose parts or panels on the appliance
• Difficulty in securing components during assembly or maintenance
• The need to replace lost or damaged screws during repair work

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It plays a critical role in the smooth operation of the refrigerator door by providing a pivot point for the hinge. This small component helps to ensure that the door opens and closes smoothly and seals properly, which is essential for maintaining the refrigerator's internal temperature and energy efficiency.

Symptoms of a bad Hinge Bearing include:

• Difficulty in opening or closing the refrigerator door.
• Squeaking or grinding noises when the door moves.
• The door hanging unevenly or not sealing correctly, potentially leading to temperature fluctuations inside the fridge.

Causes of a bad hinge bearing can include wear and tear from the frequent use of the refrigerator door, accumulation of dirt or grime that impedes smooth movement, or degradation of the material over time due to environmental factors such as moisture.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement butter dish restores a clean, secure storage area for butter and small spreads in the refrigerator door. It keeps butter contained and helps prevent odors and spills for everyday use. What it does:

• Replaces a cracked, broken, or missing butter dish in the refrigerator door dairy compartment
• Holds a stick or small portions of butter and keeps them from contacting other foods
• Helps contain crumbs and minor spills for easier cleaning of the door shelf
• Provides a neat, designated spot for butter to improve organization

• One butter dish

• No special tools required; remove the old dish from the door shelf and snap or slide the new one into place
• Clean the door shelf area before installing to ensure a secure fit
• Handle carefully to avoid chipping the plastic during installation
• If the dish doesn't seat easily, verify it is aligned with the door shelf guides before forcing

This tall bottle retainer mounts to the refrigerator door shelf to keep taller containers upright as you open and close the door. Replacing a worn or missing retainer restores secure storage and helps prevent spills.

• Attaches to the door shelf/bin to create a front barrier for tall bottles and cartons
• Helps prevent items from tipping or sliding out during door movement
• Replace if cracked, bent, missing, or if it no longer stays secured
• Common symptoms: bottles fall forward, retainer is loose or broken, difficulty keeping tall items upright

• Disconnect power and remove items from the affected door shelf/bin
• Lift out the bin if needed; release the old retainer from side brackets/clips
• Align the new retainer's ends with the supports and press in until fully seated
• Reinstall the bin and ensure the retainer holds items securely and clears the door gasket

A small white plug button that covers the lower front door opening to restore the refrigerator's finished look and keep out dirt and moisture. Simple cosmetic replacement for worn, broken, or missing door plugs. What it does:

• Covers an unused hole or fastener opening on the refrigerator's lower door front
• Restores finished appearance and helps keep out dust and moisture
• Prevents squeaks or movement from a loose/ missing plug area
• Matches factory white finish for a clean, OEM look

• One (1) white plug button for lower door front

• Usually a simple push-fit—align and press into the hole until fully seated
• If stubborn, use a small flat tool carefully to avoid scratching the door
• Power disconnect not typically required for this cosmetic part, but use caution when working around door hardware

The Door Bin is an OEM part for Frigidaire refrigerators. It provides additional storage space on the refrigerator door, allowing for the convenient organization of smaller items such as condiments, beverages, and jars. This bin is designed to fit securely into the slots on the refrigerator door, making it easy to remove and clean when necessary.

Replace this door bin if it becomes cracked, warped, or no longer fits securely in the door slots. Over time, exposure to varying temperatures and frequent use can cause the plastic to weaken and break.

Symptoms of a bad door bin include:

• Cracks or breakage in the plastic
• Difficulty in securing the bin to the door
• Items falling out or not staying in place

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Shelf Bin is an OEM replacement part for Frigidaire refrigerators. It is designed to fit on the refrigerator door, providing convenient storage space for condiments, bottles, and other small items. This shelf bin helps to keep the refrigerator organized, making it easier to find and reach items stored in the door. 

Causes of a bad door shelf bin can include cracking, breaking, or warping due to overloading, impact from items being moved in and out, or deterioration over time.

Symptoms of a bad door shelf bin include:

• Cracks or breakage in the bin.
• The bin not securely attaching to the door.
• Items falling out or not fitting properly in the bin.
• Difficulty in accessing or retrieving items from the bin.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Freezer Door Shelf Bin is an OEM replacement part for Frigidaire refrigerators. It provides adjustable storage on the inside of the freezer door with removable bin shelves. These bins maximize storage potential in the limited door space through customizable shelving.

Causes of a bad Door Shelf Bin can include shelf breakage from heavy loads, damage to supporting rails or walls of the bin inhibiting proper shelf attachment and use, or broken/missing bin walls reducing structural integrity.

Symptoms of a bad Door Shelf Bin include:

• Detached or missing shelves
• Shelves that do not stay firmly in place when loaded
• Damage or deterioration of bin walls
• Insufficient or compromised storage space

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Handle Mounting Block is an OEM part for Frigidaire refrigerators. This component anchors the refrigerator door handle assembly while also reinforcing the door structure.

Causes of a bad mounting block can include cracks developing from repeated opening/closing stresses, broken fasteners loosening its installation, or residual damage during door replacement or repair attempts.

Symptoms of a bad handle mounting block include:

• Loose, sagging or misaligned door handles
• Doors difficult to open or not staying securely closed/latched
• Noisy rattling coming from the door handle area
• Cracks or breaks visible in the mounting plastic

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Specs: 10-16 X 0.500