Parts for Ge CFCP1NIZCSS: 01 - Doors Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Refrigerator door gasket creates an airtight seal to keep cold air in. Replace if door won't seal, frost builds up, or gasket is torn. Confirm fit with model.

Commercial-style door handle assembly for refrigerator and freezer doors. Replaces cracked, broken, or missing handles to restore secure grip and clean appearance.

Stainless steel fastener that secures your refrigerator door handle to the door assembly. Replace when original is stripped, missing, or damaged.

Mounting bracket that secures and stabilizes refrigerator panels and assemblies. Replace when the original bracket is broken, cracked, or missing.

Machine screw for refrigerator panels, brackets, and assemblies. Replaces lost, stripped, or damaged fasteners to restore secure fit and stability.

Lower left-hand shelf slide bracket for refrigerators. Supports and guides sliding shelves. Replace if cracked, broken, or missing to restore smooth operation.

Secures brackets, panels, and components inside your refrigerator. Replace stripped, rusted, or missing hardware to restore tight alignment and stability.

Replace a cracked, broken, or missing lower slide-out basket in your refrigerator. Restores organized storage for produce and fresh foods.

The French Door Gasket is an OEM part for GE refrigerators. This gasket seals the gap between the French doors of the refrigerator, maintaining an airtight seal to prevent warm air from entering and cool air from escaping. It ensures the refrigerator operates efficiently by keeping the internal temperature consistent.

You should replace this French door gasket if it becomes worn out or damaged. Causes of a bad gasket include regular wear and tear, damage from cleaning, or the gasket becoming brittle over time. A compromised gasket can lead to increased energy consumption and food spoilage.

Symptoms of a bad French door gasket include:

• Warm air entering the refrigerator
• Frost buildup around the doors
• Higher than usual energy bills
• The refrigerator door not sealing properly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Refrigerator door stop cam riser that mounts to the door hinge. Replacement needed when cracked, broken, or missing to properly support the door.

Plastic retaining clip that secures drawer divider modules in place. Replaces broken, cracked, or missing snuggers to restore proper fit and separation.

Refrigerator door hinge thimble that supports the hinge pin assembly. Replace if cracked, worn, or missing to restore proper door alignment and function.

Replacement right-hand door closure cam for your refrigerator. Installs on the door hinge assembly to control closing action. Replace if cracked or worn.

Left-hand door closure cam for refrigerators. Mounts inside the door hinge assembly to control door closing action. Replace if cracked or broken.

Clear flip-up cover for the door-mounted dairy compartment. Replaces cracked, broken, or missing dairy doors to restore a clean look and keep items secure.

Refrigerator dairy door compartment that mounts on the right door to store butter, cheese, and small items. Replace if cracked, broken, or missing.

Wire beverage rack installs on refrigerator door to organize cans and bottles. Replace if broken, bent, or missing to restore door storage space.

A replacement module shelf assembly that supports and secures a refrigerator's electronic control module and wiring inside the cabinet, helping maintain proper component position and reduce vibration-related connection issues. What it does:

• Provides a stable mounting surface for the main control module and related wiring harness
• Keeps the module correctly positioned to prevent loose connections or intermittent electrical symptoms
• Helps reduce vibration and rattling that can occur when the original shelf is cracked or broken
• Maintains proper spacing to avoid contact with other components that might cause wear or shorting

• One module shelf assembly

• Disconnect power to the appliance before beginning any service
• Handle the shelf and electrical connectors gently to avoid damaging clips or wiring
• Installation typically requires basic hand tools and removing interior panels for access
• Module and harness are fully seated and secured before restoring power

This glass or wire shelf is permanently mounted inside the fresh food compartment of the refrigerator to provide storage space. Replace when the shelf is cracked, broken, or no longer securely holds items due to damaged mounting brackets.

Lower right-hand freezer rail holder mullion for your refrigerator. Replacement for cracked, broken, or missing original part. Secures interior components.

Left-hand freezer rail holder for refrigerators. Secures and stabilizes sliding drawer rails. Replace if cracked, broken, or missing to restore smooth operation.

Set screw secures refrigerator door handles in place. Replace if lost, stripped, or missing after repairs. Requires hex wrench for installation.

This articulation mullion is the flip-out center rail on a French-door refrigerator. It swings into place as the door closes to seal the gap between doors, helping maintain proper temperatures and limit moisture around the center joint.

• Provides the pivoting center rail that engages the opposite door to complete the seal
• Common signs of failure: cracked or loose mullion, won't flip or latch, doors not closing smoothly, or moisture/condensation near the center
• Helps restore proper door sealing and reduce air leaks between doors
• Mounts on the door edge in the same location as the original flipper

• Disconnect power to the refrigerator before servicing
• Remove door bins if needed for access
• Remove mounting screws, lift off the old mullion, position the new mullion, and secure with the original hardware
• Open and close the door to ensure the mullion extends, retracts, and seals correctly

Small cushioning bumper for French-door refrigerators. Prevents door rattling and protects against wear. Replace if cracked, missing, or worn out.

Bottom divider basket for refrigerator freezer compartment. Organizes frozen items and creates separate storage sections. Replace if cracked or broken.

Hex washer head screw secures panels, brackets, and small assemblies inside refrigerators and ranges. Replace stripped, missing, or damaged screws.

Fastens refrigerator panels, brackets, and internal components. Replace this screw if the original is missing, stripped, or damaged to restore secure mounting.

The Gear Pinion is an OEM component specifically designed for GE French door refrigerators. This part is responsible for the smooth operation of door hinges and closing mechanisms. 

The gear pinion works together with other inner door components to evenly distribute strength across the refrigerator’s motion system. This ensures doors move fluidly and stay securely sealed when closed. 

Causes of a bad gear pinion can include wear from repetitive use over many years, stress from overloading the doors, or misalignment of connecting mechanisms.

Symptoms of a bad gear pinion include: 

• Doors not closing or latching properly
• Binding or sticking movement  
• Noise or vibration when opening/closing
• Increased effort required to operate doors

Note: Right-hand side

Replace this precision gear with a genuine GE OEM part to restore dependable door functionality. This product is also compatible with Hotpoint, RCA, and Kenmore refrigerator models.
 

Push fastener for refrigerator interior panels and trim. Secures shelves, drawers, or housing components. Replace if broken, cracked, or missing.