Parts for Ge GTS19KGNBRBB: Doors Parts

This plastic BB handle replaces a worn or damaged refrigerator/freezer drawer or door handle so you can open and close it with a secure grip. Designed as a direct-fit exterior handle replacement for a clean, finished look. What it does:

• Replaces cracked, broken, or loose BB-style exterior handles
• Restores a secure grip for opening doors or drawers
• Keeps the appliance appearance consistent and functional
• Helps prevent further damage caused by using a damaged handle

• Disconnect power to the appliance before servicing to avoid electrical or injury risk
• Handle typically secures with mounting screws or retention clips; use appropriate screwdriver and keep hardware
• Align handle carefully to avoid scratching the appliance finish

This freezer door gasket seals the freezer door to help maintain proper temperature and reduce frost buildup. Replacing a worn or torn gasket restores the door seal for more consistent cooling and energy use. What it does:

• Creates an airtight seal around the freezer door to help keep cold air in and warm, moist air out
• Stops or reduces frost accumulation and condensation caused by a failing seal
• Helps the freezer maintain set temperature more reliably and can reduce compressor cycling
• Use when the existing gasket is torn, warped, compressed, or no longer seals evenly

• Disconnect power to the appliance before beginning any work and follow the manufacturer's safety recommendations
• Remove the old gasket, clean the gasket channel thoroughly, then align the new gasket starting from one corner and press it into the channel
• If gasket is stiff, warm it slightly (hand-warm or a hair dryer on low) to make installation easier—avoid overheating
• After installation, check the door seal around the entire perimeter and adjust or reseat as needed for an even contact

This freezer door stop cushions and limits the door's travel to protect the hinge and cabinet edge, helping the door close smoothly and preventing over-travel damage. Fits black trim locations on compatible freezers. What it does:

• Acts as a bumper to stop the freezer door from swinging too far
• Cushions impact, reducing stress on hinge components and cabinet
• Helps the door align and close flush to maintain seal performance
• Common symptom fix: door hits cabinet, scrapes, or sits unevenly

• Remove any food/obstructions and support the door before replacing the stop
• Usually a simple snap-in or screw-on replacement; small hand tools may be required
• Inspect surrounding hinge and trim for damage when replacing
• Follow all safety precautions; unplug unit or disconnect power before performing extended service

This fresh food door gasket seals the refrigerator compartment to keep cold air in and warm air out. The Dorian Gray color matches compatible units while helping maintain stable temperatures and reducing moisture at the door edge. What it does:

• Creates an airtight seal around the fresh food door to prevent air leaks
• Helps maintain proper compartment temperature and humidity
• Reduces condensation, frost, and warm spots near the door opening
• Common failure signs: gaps, cracks/tears, warped corners, or the door not closing/sealing properly

• 1 fresh food door gasket in Dorian Gray

• Disconnect power before servicing; clear items from the door for easier handling
• Warm the new gasket (soak in warm water or use a hair dryer on low) to relax and improve fit
• Press the gasket fully into the door channel; ensure corners seat evenly without twists
• After installation, close the door to help the gasket conform; check for an even seal and adjust door alignment if needed

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

This kit replaces the mounting hardware that secures a refrigerator/freezer door handle to the door, restoring a solid, safe grip and clean appearance when the original fasteners are missing, damaged, or stripped.

• Provides the correct hardware to attach and secure the door handle
• Helps resolve loose, wobbly, or detached handles
• Replaces missing, damaged, or stripped handle fasteners
• Supports proper handle alignment and feel

• Disconnect power (and water, if applicable) and wear gloves.
• Support the handle while removing old hardware to prevent drops or scratches.
• Start threads by hand to avoid cross-threading; tighten evenly and do not overtighten.
• The handle is secure and the door opens/closes normally.

This black emblem badge restores the appliance's front appearance by replacing a faded, scratched, or missing logo accent. It provides a clean, finished look so the appliance matches its original styling. What it does:

• Replaces a worn or missing badge to restore factory appearance
• Hides cosmetic damage on the control bezel or exterior trim
• Helps maintain resale value and consistent styling across the appliance lineup
• Visible cosmetic part only — does not affect appliance function

• One black emblem badge

• Clean and dry the mounting area before installing to ensure proper fit
• Align carefully before seating; some badges press into place or adhere to the surface
• Use caution around sharp edges and disconnect power when working near electrical components

This plug button thimble is a small control-panel insert that secures and centers push buttons, helping keep button caps in place and reducing moisture or debris entry. It restores proper button feel and alignment on the control panel. What it does:

• Centers and retains push-button caps so buttons press and release correctly
• Helps prevent dirt and spills from entering the control-panel opening
• Replaces a cracked, worn, or missing thimble that lets buttons wobble or fall inward
• Compatible with the original push-button assembly to restore original fit and function

• Simple, non-electrical replacement—power to the appliance is not required for this exterior part, but unplugging is recommended if removing trim near live components
• Remove the button cap first, press the old thimble out from the front or back as applicable, then press the new thimble into the panel opening until fully seated
• Inspect button cap and surrounding trim for damage; replace any damaged mating parts for best fit
• Use care to avoid scratching the control panel; keep small parts away from children

The Screw is an OEM replacement part for GE brand refrigerators. It is commonly used to secure panels, handles, shelves, or other parts of the refrigerator.

Causes of a faulty refrigerator screw can include wear and tear over time, damage due to mishandling or over-tightening, or loss of thread integrity. These factors can result in loose or ineffective connections, compromising the stability or functionality of the attached components.

Symptoms of a bad refrigerator screw may include:

• Loose or wobbly panels, handles, or shelves
• Difficulty in attaching or securing components
• Visible damage or breakage of the screw

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.