Parts for Kenmore 253.68823012 (25368823012, 253 68823012): Doors Parts

The Freezer Door Gasket is an OEM part for Frigidaire refrigerators, specifically designed to create an airtight seal around the freezer door. This gasket prevents warm air from entering and cold air from escaping the freezer compartment, ensuring efficient cooling and energy efficiency. Made from durable rubber, this gasket is flexible yet strong, designed to withstand the constant opening and closing of the freezer door.  

Causes of a bad Freezer Door Gasket can include wear and tear over time, exposure to excessive moisture leading to mold or mildew buildup, or damage from cleaning products or sharp objects. 

Symptoms of a bad Freezer Door Gasket include:

• Visible cracks, tears, or warping in the gasket.
• Condensation or ice buildup around the door edges.
• The freezer struggles to maintain the set temperature.
• Increased energy consumption as the freezer works harder to keep cold.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This freezer door gasket is an OEM replacement part for Frigidaire refrigerators. The gasket measures approximately 28" wide x 18" long. This gasket is a perfect fit for your refrigerator's inner door panel.

Symptoms of a bad freezer door gasket include:

• Difficulty keeping interior cold temperatures below 0°F  
• Frost buildup around top and sides of door seals
• Defrosts required increasing in frequency
• Visible air gaps noticeable along gasket perimeter

Causes of a bad freezer door gasket can include material breakdown due to hundreds of door opening and closing compression cycles over time developing small cracks in the rubber. Spills along bottom edges may promote seal deterioration if not cleaned promptly.

This genuine Frigidaire replacement gasket is compatible with other brands such as Electrolux and Kenmore as well 

NOTE: To achieve a smooth installation, simply soak the gasket in warm water or use a hair dryer on low heat to eliminate any folds or creases.

Replaces a worn refrigerator door seal on the fresh-food compartment to restore a tight, even seal. Helps maintain cold temperatures, reduce condensation around the door, and cut energy loss when the old gasket is torn, warped, or gapped.

What it does

• Creates a continuous seal around the fresh-food door to keep cold air in.
• Helps prevent warm-air leaks that cause temperature swings.
• Reduces moisture/sweating along the door edge.
• Addresses gaps, tears, cracks, or a gasket that won’t lie flat.

What’s included
One refrigerator door gasket for the fresh-food door (black).

Install notes

• Unplug the refrigerator before starting.
• Warm the new gasket (soak in warm water or use low-heat hair dryer) to relax folds.
• Seat the gasket lip fully into the door channel—start at the corners and work around.
• Close the door and check for uniform contact (paper-pull test); level/adjust hinges as needed and allow 24 hours for the gasket to conform.

The Refrigerator Door Gasket is an OEM replacement part for Frigidaire refrigerators. This crucial component is responsible for creating an airtight seal around the refrigerator door, ensuring efficient temperature control and energy conservation. This gasket is "approximately" 28” by 41”, and may require a screwdriver to remove the old gasket.

Symptoms of needing to replace the refrigerator door gasket include:

• Difficulty in closing the refrigerator door properly
• Visible gaps or gaps around the door gasket area
• Condensation buildup or frost formation around the door gasket
• Increased energy consumption due to inefficient sealing

Causes of a faulty door gasket can include normal wear and tear over time, exposure to extreme temperatures or UV light, or physical damage due to impact or mishandling.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

The Dairy Door is an OEM replacement part for Frigidaire side-by-side refrigerators. As the access point to the dedicated dairy compartment, the door is designed with precision seals to maintain optimal humidity levels inside. This helps keep dairy and other perishable items fresh longer.

Causes of a bad dairy door can include worn or damaged seals, dents or impacts warping the door frame, or issues with the electronic components that control humidity levels.

Symptoms of a bad dairy door include: 

• Excessive frost or ice buildup inside the dairy compartment   
• Difficulty opening and closing the door smoothly  
• Warm or dried-out dairy products despite a cold refrigerator interior
• Moisture leaks around the door seals  

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore side-by-side models.

A small replacement plug button that restores the tactile control on compatible Frigidaire appliances. Replaces a cracked, worn or missing push-button so controls operate and look complete again. What it does:

• Acts as the user-facing push surface for a specific control or plug feature
• Restores normal button feel and engagement when the original is broken or missing
• Helps prevent debris from entering the switch or control opening
• Improves appearance of a damaged or worn control panel area

• Power off and unplug the appliance before starting any repair
• Usually installs by snapping into the control panel from the front; no special tools required
• Install gently to avoid damaging the surrounding bezel or switch

This small black plug/button covers a hinge or bearing access hole to restore a finished appearance and help keep out dirt and debris. It's a simple, inexpensive trim piece that maintains the appliance's look and helps protect internal components. What it does:

• Covers exposed hinge or bearing access holes for a clean, finished appearance
• Helps keep dust and debris out of hinge or bearing cavities
• Prevents snagging and reduces the chance of small items entering the opening
• Matches factory appearance and fit for a seamless repair

• Push-fit design; press into the hole until fully seated
• Keep away from small children — small part is a choking hazard

Color: White. Used to cover the hinge bearing hole.

This door stop is the replacement limiter that keeps an appliance door from over-rotating, protecting hinges and cabinet edges. It restores consistent door travel and helps the door close smoothly and securely. What it does:

• Limits how far the door opens to prevent hinge or cabinet damage
• Helps the door close in the correct position and reduces slamming
• Fits into the door/hinge assembly to provide a stable stop point
• Common symptom: door opens too far, bangs against surrounding cabinetry, or hang/align issues

• High-level replacement — remove door/hinge trim as needed per your model's instructions
• Use basic hand tools; keep fasteners separate and note orientation for reassembly
• Disconnect power if working near electrical components (applies to ovens/microwaves)

This door stop limits the opening range of your refrigerator door to prevent overextension and hinge strain. Replace a worn or broken stop to restore controlled door movement and protect surrounding cabinetry from accidental impacts. What it does:

• Controls how far the door opens to prevent overextension and damage
• Helps maintain proper door alignment and reduces stress on the hinges
• Replaces cracked, deformed, or missing stops that no longer hold the door at its stop point
• Common symptoms include the door swinging too far, a hard "clunk" at full open, or visible damage to the stop

• 1 door stop

• Disconnect power; turn off water supply if your unit has a dispenser/ice maker
• Support the door before loosening any hinge fasteners to access the stop
• Note the stop's orientation and position; transfer any spacers and reinstall the same way
• Open and close the door to verify proper range and clearance before fully tightening fasteners

This door stop limits the refrigerator door's opening range to protect hinges and nearby cabinets. Replace a cracked or missing stop to restore smooth, controlled door movement and help the door close and seal properly.

• Limits door swing to prevent overextension and impact with walls or cabinets
• Reduces hinge stress and helps maintain proper door alignment
• Common signs of failure: door opens too far, binds at the hinge, or the original stop is cracked/missing
• Restores smooth, controlled door motion and closure

• Disconnect power and remove items from the door to reduce weight
• Support the door before loosening any hinge fasteners
• Install the new stop in the correct orientation for your model
• Adjust hinges if needed

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small black replacement plug button that restores a clean, finished appearance and helps keep controls and openings free from dirt and moisture. Designed as a direct-fit cosmetic and protective cap for compatible appliance openings. What it does

• Covers exposed holes or button openings to prevent debris and spills from entering internal areas
• Restores the original look where a worn or missing plug detracts from the appliance finish
• Holds in place to protect underlying components from accidental contact
• Useful when replacing control bezels or trim that require a matching push-in cap

• Disconnect power to the appliance before performing any service work
• Press the plug button squarely into the opening until it snaps into place; no special tools typically required
• Inspect the mounting hole for damage or debris before installing to ensure a secure fit
• If the part does not seat properly, do not force it; verify correct part and orientation

Color: White

This handle set is the OEM replacement door handle that restores a secure, comfortable grip for opening and appliance doors. It replaces worn, cracked, or broken handles to improve everyday use and appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, broken, or loose handles and helps eliminate wobble
• Restores original fit and appearance when the original handle is damaged
• Matches mounting points on the original door for a direct replacement

• Disconnect power and empty the door before starting work to avoid injury or damage
• Use the existing mounting screws and hardware; keep removed fasteners for reassembly
• Support the door while removing or installing the handle to prevent dropping or misalignment

This handle set is the OEM replacement door handle that restores a secure, comfortable grip for opening and appliance doors. It replaces worn, cracked, or broken handles to improve everyday use and appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, broken, or loose handles and helps eliminate wobble
• Restores original fit and appearance when the original handle is damaged
• Matches mounting points on the original door for a direct replacement

• Disconnect power and empty the door before starting work to avoid injury or damage
• Use the existing mounting screws and hardware; keep removed fasteners for reassembly
• Support the door while removing or installing the handle to prevent dropping or misalignment

This refrigerator door handle restores a secure, comfortable grip so you can open and close the door with confidence. Replace a cracked or loose handle to refresh your appliance's look and keep everyday use hassle-free.

• Provides the handhold used to open and close the refrigerator or freezer door
• Replaces cracked, broken, or missing handles
• Helps correct a loose or wobbly handle
• Can make the door easier to open when the old handle is damaged
• Restores the appliance's original appearance

• Unplug the refrigerator before servicing and wear cut-resistant gloves.
• Protect the door finish; remove any trim caps or set screws (as applicable) and detach the old handle.
• Align the new handle on the mounting studs and tighten screws evenly; do not overtighten.
• Verify the handle is secure and the door opens, closes, and seals properly.

The Door Handle is an OEM part for Frigidaire refrigerators. This part provides a secure grip for opening and closing the refrigerator door. This handle is essential for daily use, ensuring easy and convenient access to the refrigerator's contents.

Over time, the door handle can become worn out or damaged due to frequent use, mishandling, or accidental impacts.  

Symptoms of a bad door handle include:

• Looseness or wobbling when pulled
• Cracks or breaks in the handle material
• Difficulty in opening or closing the door
• The handle detaching from the door

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Handle is an OEM part for Frigidaire refrigerators. This handle is designed to provide a secure and comfortable grip for opening and closing the refrigerator door. It is constructed to match the refrigerator’s aesthetic while ensuring durability and functionality.

Over time, door handles can become loose, cracked, or completely broken due to regular use and the constant stress of opening and closing the refrigerator. Causes of a bad door handle include wear and tear, impact damage, or loosening of mounting screws.

Symptoms of a bad door handle include:

• The handle feeling loose or wobbly
• Cracks or visible damage on the handle
• Difficulty in opening or closing the door due to handle issues

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Handle is an OEM part for Frigidaire refrigerators. This component allows users to open and close the refrigerator door easily. It is designed to fit securely on the refrigerator door, providing a sturdy and comfortable grip. It is important to note that the necessary mounting screws are not included with the handle and must be gotten separately. 

Causes of a bad door handle can include wear and tear from frequent use, accidental impact, or damage during cleaning. The handle might also become loose or break if the screws or mounting points are compromised.

Symptoms of a bad door handle include:

• The handle feeling loose or wobbly
• Visible cracks or damage to the handle
• Difficulty in opening or closing the refrigerator door
• The handle detaching from the door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Handle is an OEM replacement part for Frigidaire refrigerators. It consists of the refrigerator door handle assembly, which allows for the opening and closing of the refrigerator door. 

Symptoms of a bad handle-door include:

• Loose, wobbly, or improperly installed door handle  
• Difficulty opening or closing the refrigerator door
• Damage or cracks in the door handle assembly
• The door not sealing properly when closed

Causes of a bad handle door can be normal wear and tear over time, accidental damage from impact, or overtightening of screws during installation. 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM part for Frigidaire appliances. This specific screw is designed for Frigidaire models, ensuring a secure fit and proper function in the appliance assembly. Screws like this one are critical for holding components together tightly, contributing to the overall stability and durability of the appliance. Whether used in refrigerators, ovens, washers, or dryers, this screw plays a pivotal role in assembly and maintenance tasks, ensuring parts remain securely fastened during operation.

Over time, screws can become loose, stripped, or lost during repairs or adjustments, potentially compromising the appliance's integrity and performance.  

Symptoms of needing replacement screws include:

• Loose parts or panels on the appliance
• Difficulty in securing components during assembly or maintenance
• The need to replace lost or damaged screws during repair work

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Screw Kit is an OEM part for Frigidaire appliances. It contains various screws specifically designed to fit and secure different components of Frigidaire appliances, ensuring a tight and secure assembly. This kit is essential for both initial installations and for making repairs or replacements to existing appliances, providing the necessary hardware to maintain or restore the structural integrity of your appliance.  These screws are #10-16 x .500 inches long and can be loosened or tightened using either a Phillips-head or square-head screwdriver.

Symptoms of needing a new Screw Kit include:

• Loose components or panels on your appliance due to missing or damaged screws.
• Inability to securely fasten parts during assembly or repairs, which can lead to operational issues or safety hazards.
• Screws stripping or corroding over time, which can compromise the stability and durability of the appliance.

Causes for replacing screws can include mechanical stress that causes screws to loosen or fall out, environmental factors like moisture leading to corrosion, or accidental damage during cleaning or maintenance.

This screw kit is designed to be universally compatible with various Frigidaire models, ensuring that you have the right screws for a range of repair needs.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It is designed to facilitate the smooth opening and closing of the refrigerator door by providing a pivot point for the door hinge. This bearing ensures that the door moves easily and remains properly aligned, helping to maintain a tight seal and optimal refrigerator performance.

Causes of a bad hinge bearing can include regular wear and tear from frequent use, exposure to moisture or temperature changes, and physical damage due to accidental impacts. Over time, these factors can cause the hinge bearing to wear out, become loose, or break, affecting the door's functionality.

Symptoms of a bad hinge bearing include:

• Difficulty opening or closing the refrigerator door
• The door not staying in place or sagging
• Unusual noises, such as squeaking or grinding, when the door is moved
• The door not sealing properly, leading to temperature fluctuations inside the refrigerator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It plays a critical role in the smooth operation of the refrigerator door by providing a pivot point for the hinge. This small component helps to ensure that the door opens and closes smoothly and seals properly, which is essential for maintaining the refrigerator's internal temperature and energy efficiency.

Symptoms of a bad Hinge Bearing include:

• Difficulty in opening or closing the refrigerator door.
• Squeaking or grinding noises when the door moves.
• The door hanging unevenly or not sealing correctly, potentially leading to temperature fluctuations inside the fridge.

Causes of a bad hinge bearing can include wear and tear from the frequent use of the refrigerator door, accumulation of dirt or grime that impedes smooth movement, or degradation of the material over time due to environmental factors such as moisture.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Bin is an OEM part for Frigidaire refrigerators. It provides additional storage space on the refrigerator door, allowing for the convenient organization of smaller items such as condiments, beverages, and jars. This bin is designed to fit securely into the slots on the refrigerator door, making it easy to remove and clean when necessary.

Replace this door bin if it becomes cracked, warped, or no longer fits securely in the door slots. Over time, exposure to varying temperatures and frequent use can cause the plastic to weaken and break.

Symptoms of a bad door bin include:

• Cracks or breakage in the plastic
• Difficulty in securing the bin to the door
• Items falling out or not staying in place

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Freezer Door Shelf is an OEM replacement part specific to Frigidaire freezers. It provides versatile storage within the freezer door compartment, allowing for the organization of frozen items. The shelf is designed to withstand cold temperatures while smoothly sliding in and out. This shelf measures approximately 23" x 4".

Symptoms of a bad door shelf include:

• Difficulty sliding or complete inability to slide the shelf in and out
• Warping, cracking, or breaking of shelf material
• Loss of level plane, creating an unstable storage surface
• Food items potentially falling through large cracks or holes

Causes of a bad shelf often stem from repetitive use over several years and exposure to temperature fluctuations. Normal wear and tear can compromise the integrity of plastic components.

This OEM Frigidaire replacement shelf is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Handle Mounting Block is an OEM part for Frigidaire refrigerators. This component secures the door handle to the refrigerator door, ensuring it remains firmly attached and easy to use.

Causes of a bad mounting block can include repeated use leading to wear and tear, accidental damage, or improper installation that causes it to loosen or break.

Symptoms of a bad door handle mounting block include:

• The door handle feeling loose or wobbly
• Difficulty in opening or closing the refrigerator door
• The door handle detaching from the door
• Visible cracks or damage to the mounting block

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.