Parts for Ge DDE8200BAC: 02 - Blower & Drive Asm. Parts

Size: 14-10 a.

7" diameter

This replacement motor strap secures the dryer's drive motor to its mounting bracket so the motor and blower stay aligned and stable, helping reduce vibration and noise for smoother operation. What it does:

• Holds the drive motor firmly to the base/bracket
• Maintains proper alignment of the motor and blower wheel to prevent rubbing
• Helps reduce vibration, rattling, and related noise
• Typical signs of failure: increased vibration, rattling, scraping from the blower area, or a motor that feels loose inside the cabinet

• Includes 1 motor strap

• Disconnect power; for gas dryers, also shut off gas supply
• Access the motor assembly; note the strap's routing/orientation before removal
• Support the motor while releasing the strap to avoid stressing wiring and mounts
• After securing the strap, rotate the drum/blower by hand to verify free movement before reassembly

This motor strap secures the appliance motor to the cabinet, keeping the motor stable during operation to reduce vibration and noise. Use this replacement to restore proper motor positioning and support in compatible models. What it does:

• Holds the motor firmly in place to prevent movement or shifting during use
• Helps reduce vibration and associated noise caused by a loose motor
• Maintains correct motor alignment so belts and linkages run smoothly
• Commonly used when a worn or broken strap allows motor sag or misalignment

• One motor mounting/retaining strap

• Disconnect power to the appliance before beginning any work
• Inspect mounting points and fasteners; replace any damaged hardware as needed
• Secure strap to the motor and cabinet using the original mounting holes and recommended hardware

Length - 99", groove - 4J

This idler pulley keeps tension on the dryer drum belt so the motor can spin the drum smoothly. Replacing a worn pulley can quiet squealing and restore consistent tumbling.

• Maintains proper belt tension so the drum turns under load
• Free-spinning pulley reduces friction and belt wear
• Common symptoms of failure: squealing/chirping noises, drum won't turn, belt slipping or fraying, burning rubber smell
• Helps prevent the belt from jumping off the motor or drum

• Disconnect power; for gas dryers, shut off the gas supply
• Access typically requires removing the top/front panel and releasing belt tension to remove the drum
• Transfer any spacers/retainer from the old pulley to the new one; the pulley spins freely before reassembly
• Route the belt per the model's diagram and check belt alignment/tension before test run

The High Limit Thermostat is an OEM part for GE dryers. It is a safety device that prevents the dryer from overheating by cutting off power to the heating element if the temperature exceeds a safe limit. This helps protect the dryer and the user from potential fire hazards.

Causes of a bad high limit thermostat can include electrical faults, repeated exposure to high temperatures, or wear and tear over time. When the thermostat fails, it may either keep the dryer from heating or cause it to overheat.

Symptoms of a bad high limit thermostat include:

• The dryer not heating at all
• The dryer overheating and shutting down mid-cycle
• Clothes taking longer than usual to dry
• The dryer running but not producing any heat

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Rear Drum Bearing Kit is an OEM replacement part for GE dryers. It is a comprehensive kit that includes both rear drum bearings and necessary mounting hardware. These bearings play a vital role in smoothly rotating the dryer drum during cycles, reducing vibrations and noise.  

Symptoms of bad bearings include:

• Excessive shaking or vibrating during cycles
• Loud grinding or scraping noises emanating from the rear drum area   
• Difficulty turning or rotating the dryer drum by hand
• Increased wear and early failure of other components 

Causes of bad bearings can include normal wear and tear over time, exposure to excessive loads or unbalanced loads that strained the bearings, or damage from extended use without proper lubrication.

This OEM replacement is also compatible with Hotpoint, RCA, and some Kenmore models.

Package of 12

This dryer heating element kit is made by GE and includes two coils and hardware. Rated 240 volts.

The Rear Drum Bearing Kit is an OEM replacement part for GE dryers. It is a comprehensive kit that includes both rear drum bearings and necessary mounting hardware. These bearings play a vital role in smoothly rotating the dryer drum during cycles, reducing vibrations and noise.  

Symptoms of bad bearings include:

• Excessive shaking or vibrating during cycles
• Loud grinding or scraping noises emanating from the rear drum area   
• Difficulty turning or rotating the dryer drum by hand
• Increased wear and early failure of other components 

Causes of bad bearings can include normal wear and tear over time, exposure to excessive loads or unbalanced loads that strained the bearings, or damage from extended use without proper lubrication.

This OEM replacement is also compatible with Hotpoint, RCA, and some Kenmore models.

Bearing only, to get complete assembly order WE25M40

Size: 8-15 HX 3/8 S. Includes 12 screws.

This dryer motor kit powers the drum and blower. Replacing a weak or failed motor restores proper tumbling and airflow so the dryer starts reliably and dries loads more evenly.

• Drives the drum via the belt and turns the blower wheel for airflow
• Helps resolve: dryer hums but won't start, drum won't turn, or stops mid-cycle
• Can reduce loud buzzing/grinding noises from the motor area
• Restores consistent operation when the motor overheats and trips its protector

• Disconnect power; turn off gas supply to gas dryers before servicing
• Remove panels to access the drive system; release belt tension and remove the drum as needed
• The blower wheel threads onto the motor shaft—support it carefully; many GE dryers use a reverse (left-hand) thread
• Transfer wiring and any reusable hardware to the new motor; test before reassembly