Parts for Ge DBB3300GA2AA: 03 - Drum Parts

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.

This screw is a factory replacement fastener used to secure appliance panels and components. It restores lost or loose hardware so parts sit correctly and operate without rattling or movement. What it does

• Secures panels, brackets, and small com

This replacement screw secures appliance panels and internal components per your model's hardware list. Replace lost or stripped screws to keep assemblies tight, reduce vibration and rattles, and maintain proper alignment.

• Fastens brackets, cove

Front bulkhead drum assembly for dryers. Replaces cracked, damaged, or worn drum housing. Installs at front of dryer drum to support rotation assembly.

Fix melted plastic or goop marks on clothes with a new dryer heat diffuser. Replaces damaged diffuser that causes staining. DIY repair with 3 screws.

Rear drum bearing kit supports and smoothly rotates your dryer drum. Replace when you hear squealing, screeching, or grinding noises. Verify fit with your model.

Replacement drum baffle installs inside your dryer to lift and tumble clothes during drying. Replace if cracked, broken, or mounting holes are stripped out.

Ground strap assembly connects drum shaft to dryer frame for electrical safety. Replace if damaged, corroded, or causing startup squealing noise.

This combustion chamber is the metal housing that surrounds and directs the gas burner flame in a gas dryer, protecting surrounding components and guiding combustion for reliable heating performance. What it does

• Houses and aligns the burner assembly and igniter to ensure proper flame direction
• Channels exhaust and combustion flow away from sensitive parts
• Helps prevent heat damage to the dryer cabinet and nearby components
• Symptoms this can fix: poor or uneven heating, burner flame misalignment, or burner noise from loose housing

• One combustion chamber housing

• Turn off and unplug the dryer and shut off the gas supply before servicing
• Inspect and replace any damaged gaskets or mounting hardware for a proper seal
• Use basic hand tools; avoid bending or deforming the chamber during installation

Transition duct connects your dryer to the wall vent exhaust system. Replace if cracked, torn, or damaged to restore proper airflow and venting.

This replacement part is a high-limit thermostat, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This high-limit thermostat is typically found in dryers and controls the heat inside the drying tub. This is especially important as different dryer settings require different amounts of heat. If the high limit thermostat works properly, the temperature inside the tub should reach the correct amount during each drying cycle with no issues. A new high-limit thermostat might be needed if the user notices that the dryer is unable to reach the appropriate level of heat for a certain drying cycle. This is also true if the dryer is becoming too hot when the heat is supposed to be set to low. Make sure the dryer is cooled down prior to replacing this part as the areas in the back of the dryer can become very hot during use. Be sure to reference the specific user manual for more instructions on how to replace the thermostat. This thermostat is sold individually and is a genuine OEM part. The thermostat is sourced directly from the manufacturer.

This gas diffuser directs and evens the burner flame for reliable cooking performance. It helps stabilize heat distribution so burners light and heat more consistently across cookware. What it does:

• Spreads and evens gas flame to reduce hot spot

This is a small screw, and it is made for dryers, washers, and washer dryer combos. This is a genuine replacement part made by General Electric. Screws are common in these appliances and can cause many difficulties if they become loose, damaged, or missin

The Flame Sensor is an OEM part for GE dryers. This part detects the presence of a flame in gas dryers, ensuring that the gas ignites properly for safe and efficient drying.

Causes of a bad flame sensor can include regular wear and tear, c

The bearing retainer secures the drum bearing assembly in your dryer. Replace if cracked, broken, or worn to restore proper structural support.

Supports the rear dryer drum for smooth, quiet rotation. Replace if you hear squeaking, screeching, or thumping during cycles. Verify fit with your model.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where

The O Ring is an OEM part for GE dryers, creating a tight seal in different components for efficient operation. This small part prevents air leaks that can impact drying performance, made from quality materials to withstand high temperatures and freque