Parts for Kenmore 110.81442710 (11081442710, 110 81442710): Dryer Control Panel Parts

The timer knob assembly lets you turn and set the appliance's mechanical timer. When the original knob is cracked, stripped, or missing, this replacement restores a secure grip so cycles or time settings can be selected reliably.

• Attaches to the timer shaft to select cycles or time settings
• Restores positive engagement when the original knob is worn or broken
• Common fix for a knob that spins freely, slips, or falls off
• Helps resolve difficulty setting or starting a cycle caused by a damaged knob

• Disconnect power to the appliance before replacing the knob
• Pull the old knob straight off the timer shaft; if tight, gently wiggle while pulling
• Align the new knob with the shaft and press firmly until fully seated
• Verify smooth operation through the full range of timer positions

The Knob Spring Clip is an OEM part for Whirlpool appliances, specifically designed for use in washers and dryers. This small but essential component is responsible for securing the control knob to the control panel, ensuring that the knob stays firmly in place during operation.

Common causes of a bad spring clip include frequent use, accidental impacts, or wear and tear over time. A faulty spring clip can result in the control knob becoming loose or falling off, making it difficult to operate the appliance.

Symptoms of a bad knob spring clip include:

• The control knob is loose or wobbly
• The control knob falls off easily
• Difficulty in turning or setting the control knob
• The appliance not responding correctly to knob adjustments

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A genuine replacement screw used to secure appliance panels, brackets, and components so assemblies stay aligned and stable. Installs quickly with a screwdriver or driver bit to restore proper fit and reduce rattling. What it does:

• Secures panels, trim, brackets or internal components to keep parts properly aligned
• Prevents loose or vibrating panels that can cause noise or wear
• Holds mounting points that keep doors, seals, and assemblies operating correctly
• Replaces stripped, missing, or corroded fasteners that compromise fit

• Turn off and unplug the appliance before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or deform parts
• Keep removed hardware organized and replace like-for-like for best fit

This control panel is the user interface that lets you select cycles and settings and shows status information. It replaces a worn, cracked, or unresponsive front panel to restore normal control operation. What it does:

• Houses the buttons/touch areas and display used to start and program the appliance
• Sends signals to the control board when you change settings or start a cycle
• Restores visible status indicators and accessible controls if the original panel is damaged
• Addresses symptoms like unresponsive buttons, missing display segments, or cosmetic damage

• Disconnect power to the appliance before starting any work
• Handle the panel carefully to avoid damaging the display, ribbon cable, or connectors
• Installation typically requires removing trim and fastening screws; keep track of hardware

This pushbutton replaces a worn or broken control-panel button so you can reliably select settings and start or stop cycles. It restores tactile feedback and normal button operation on compatible Whirlpool appliances. What it does:

• Acts as a user-control button on the appliance control panel for selecting options or starting/stopping cycles
• Restores tactile push response when original button is cracked, stuck, or unresponsive
• Helps resolve symptoms like buttons that don't depress, intermittent selection, or missing tactile feedback
• Designed to mate with the factory switch or keypad assembly for a proper fit

• One pushbutton

• Disconnect power to the appliance before beginning any repair
• Access may require removing the control panel or console; keep fasteners organized
• Handle plastic components gently to avoid cracking; align button with the switch or keypad when reinstalling
• Test button operation after reassembly to ensure proper function

Specs: 10-16 x 1/2 inch.

The Start Switch is an OEM part for Whirlpool dryers. This part initiates the drying cycle when you press the start button on the control panel. This switch sends a signal to the dryer to begin operation, ensuring your clothes drying process starts smoothly.

Causes of a bad start switch can include repeated use over time leading to wear and tear, electrical issues such as short circuits or power surges, and physical damage due to mishandling or impact. 

Symptoms of a bad start switch include:

• The dryer not starting when the button is pressed
• The dryer stopping unexpectedly during a cycle
• No response or sound when pressing the start button
• Intermittent operation or the need to press the button multiple times

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Timer is an OEM part for Whirlpool dryers, designed to control the duration of various drying cycles. This part ensures your dryer operates efficiently, cycling through its programmed times for drying, cooling, and tumbling. 

Common causes of a malfunctioning dryer timer include corrosion or wear of electrical contacts, mechanical failure from stuck gears, and electrical shorts impacting circuitry.

Symptoms of a failing Timer include:

• The dryer not starting or stopping at the correct time.
• The dryer skipping certain parts of a cycle or not advancing through cycles at all.
• Inconsistent drying times, leading to clothes being either too damp or overly dry.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This part is a moisture sensor control board that is used on dryer units. This component monitors the moisture levels within the dryer and adjusts the dry time during the automatic drying cycle. A new moisture sensor control board will be needed if the time is not advancing in the automatic drying cycle, even if it does advance in the timed dry cycle. Another sign is if the dryer continues to run after the clothing inside is dry. Unplug the dryer from its power source prior to replacing this component. The person performing this task may wish to wear work gloves to protect their hands.The moisture sensor control board is compatible with dryers that are manufactured by Kenmore, KitchenAid, Kenmore Elite, Whirlpool, Amana, Crosley, Maytag, Inglis, Sears Canada, Roper, and Sears. This part is sold individually and it is a genuine OEM replacement part that comes straight from the manufacturer.