Parts for Kenmore 110.81452710 (11081452710, 110 81452710): Dryer Control Panel Parts

The timer knob assembly lets you turn and set the appliance's mechanical timer. When the original knob is cracked, stripped, or missing, this replacement restores a secure grip so cycles or time settings can be selected reliably.

• Attaches to the timer shaft to select cycles or time settings
• Restores positive engagement when the original knob is worn or broken
• Common fix for a knob that spins freely, slips, or falls off
• Helps resolve difficulty setting or starting a cycle caused by a damaged knob

• Disconnect power to the appliance before replacing the knob
• Pull the old knob straight off the timer shaft; if tight, gently wiggle while pulling
• Align the new knob with the shaft and press firmly until fully seated
• Verify smooth operation through the full range of timer positions

The Knob Spring Clip is an OEM part for Whirlpool appliances, specifically designed for use in washers and dryers. This small but essential component is responsible for securing the control knob to the control panel, ensuring that the knob stays firmly in place during operation.

Common causes of a bad spring clip include frequent use, accidental impacts, or wear and tear over time. A faulty spring clip can result in the control knob becoming loose or falling off, making it difficult to operate the appliance.

Symptoms of a bad knob spring clip include:

• The control knob is loose or wobbly
• The control knob falls off easily
• Difficulty in turning or setting the control knob
• The appliance not responding correctly to knob adjustments

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A genuine replacement screw used to secure appliance panels, brackets, and components so assemblies stay aligned and stable. Installs quickly with a screwdriver or driver bit to restore proper fit and reduce rattling. What it does:

• Secures panels, trim, brackets or internal components to keep parts properly aligned
• Prevents loose or vibrating panels that can cause noise or wear
• Holds mounting points that keep doors, seals, and assemblies operating correctly
• Replaces stripped, missing, or corroded fasteners that compromise fit

• Turn off and unplug the appliance before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or deform parts
• Keep removed hardware organized and replace like-for-like for best fit

This control panel is the appliance's front user interface that lets you select cycles, options, and settings. It replaces a failed or unresponsive panel to restore normal control and display feedback for the unit. What it does:

• Provides the buttons/touchpad and display used to choose cycles, temperatures, and options
• Sends user selections to the appliance's main control board so selected operations start
• Commonly replaced for symptoms like unresponsive or sticky buttons, incorrect cycle selection, or blank/misaligned display
• Works with the appliance's existing mounting hardware and wiring harness

• One control panel assembly

• Disconnect power to the appliance before beginning any work
• Handle the panel and any attached ribbon or wire harnesses carefully to avoid damage
• Installation typically requires removal of the trim or console and careful reconnection of electrical connectors

This pushbutton replaces a worn or broken control-panel button so you can reliably select settings and start or stop cycles. It restores tactile feedback and normal button operation on compatible Whirlpool appliances. What it does:

• Acts as a user-control button on the appliance control panel for selecting options or starting/stopping cycles
• Restores tactile push response when original button is cracked, stuck, or unresponsive
• Helps resolve symptoms like buttons that don't depress, intermittent selection, or missing tactile feedback
• Designed to mate with the factory switch or keypad assembly for a proper fit

• One pushbutton

• Disconnect power to the appliance before beginning any repair
• Access may require removing the control panel or console; keep fasteners organized
• Handle plastic components gently to avoid cracking; align button with the switch or keypad when reinstalling
• Test button operation after reassembly to ensure proper function

Specs: 10-16 x 1/2 inch.

The Push to Start Switch is an OEM part for Whirlpool dryers. It is responsible for initiating the drying cycle when pressed, sending an electrical signal to start the dryer.

You should replace this push to start switch if it becomes defective. Causes of a bad switch can include electrical failures, physical damage from repeated use, or internal wear over time.

Symptoms of a bad push to start switch include:

• The dryer not starting when the button is pressed
• The need to press the button multiple times to start the dryer
• No response or clicking sound when the button is pressed

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: For square top push to start switch, use part number W10156101.

This Timer is the mechanical cycle controller for your appliance. It sequences power to components so cycles start, advance, and end at the proper times, helping restore dependable operation when the original timer wears or fails.

• Sequences power to motors, valves, and heaters according to the cycle selected at the timer shaft
• Advances the machine through each stage via a motor-driven cam and internal contacts
• Symptoms: cycle doesn't advance or stops mid-cycle
• Symptoms: appliance won't start or only starts intermittently
• Symptoms: runs past the end of the cycle or won't shut off

• Disconnect power before servicing; shut off water supply
• Photograph wiring and transfer wires to the same labeled terminals one at a time
• Reuse the original mounting hardware, dial, and knob
• After installation, run a short test cycle to ensure the timer advances properly

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.