Electrolux Range / Cooktop / Oven Parts

This holder is a small mounting bracket that secures internal appliance components to prevent movement and maintain proper alignment, helping reduce noise and keep parts functioning reliably. What it does:

• Secures and positions an internal component or assembly to the appliance frame
• Prevents shifting or sagging that can cause rattling or misalignment
• Helps maintain proper spacing for connected parts to operate correctly
• Reduces noise caused by loose fittings or vibration

• Recommended for users comfortable with appliance repair; disconnect power before servicing
• Remove adjacent panels or components as needed for access; keep fasteners organized
• Inspect mating surfaces and replace any damaged screws or clips for a secure fit

This metal angle support bracket secures appliance panels and components to the cabinet, helping maintain alignment and stability for long-lasting operation. Use it to replace a bent, cracked, or missing bracket that lets panels shift or rattle. What it does

• Provides a stable mounting point for panels, housings, or internal components
• Restores proper alignment when a corner or panel sits uneven or gaps appear
• Reduces vibration and rattling caused by loose or damaged supports
• Helps prevent further wear from components rubbing or shifting out of place

• Disconnect power to the appliance before starting any repair
• Use the existing fasteners when possible; replace stripped or damaged screws
• Verify correct orientation and alignment before fully tightening fasteners
• Take care to avoid damaging seals or wiring

Replacement burner grate kit for your range cooktop. Installs over burner elements to support cookware. Replace if grates are cracked, corroded, or worn.

This insulation panel fits inside the refrigerator cabinet to help maintain interior temperatures and reduce heat transfer to the outer shell, supporting more consistent cooling and helping limit frost buildup. What it does:

• Forms a thermal barrier between the interior liner and outer cabinet to help hold cold air inside.
• Helps reduce frost and moisture buildup around the liner when intact.
• Worn, torn, or missing insulation can contribute to longer run times, uneven cooling, or more frequent defrost cycles.
• Replaces damaged insulation to restore proper temperature retention and improve appliance efficiency.

• Always disconnect power to the appliance before starting any repair.
• Panel may be secured with clips, adhesive, or foam sealant; remove and install carefully to avoid damaging the liner.
• Inspect surrounding seals, gaskets, and fasteners while accessing the cavity; replace any damaged components.

Bake element restores oven heat by producing the radiant heat needed for baking and roasting. Replacing a worn or damaged bake element helps the oven reach and maintain set temperatures for more consistent cooking results. What it does:

• Heats the oven cavity to provide direct radiant heat for baking and roasting.
• Use when the element shows visible breaks, blistering, or does not glow when the oven is set to high.
• Common symptom indicators: oven won't reach set temperature, uneven baking, or longer-than-normal cook times.
• Works as a direct replacement for the oven's lower/bake heating element.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Allow the oven to cool completely and wear gloves to avoid sharp edges.
• Match the part to your model and terminal layout before installing; tighten connections securely.

For 12k burner.

Secures burner or oven control to the control panel behind the knob. Replace if stripped, missing, or loose to keep control shaft stable and aligned.

If your range displays E15 error codes, won't turn off, or has no oven heat, the electronic control board likely failed. Moderate DIY repair in 1-2 hours.

Adapter assembly for oven vent system. Installs in back wall to align vent components. Replace if cracked, broken, or missing to restore proper fit.

Heat-resistant insulation that wraps the oven cavity to contain heat. Replace if worn, damaged, or missing to improve heat retention and efficiency.

This is a flexible gasket that seals around the oven door to prevent heat from escaping during cooking. It fits into a channel along the perimeter of the oven door or oven frame. Replace this gasket if you notice heat leaking from the oven door, uneven cooking temperatures, the oven not reaching the set temperature, or if the gasket is visibly worn, torn, or hardened.

This wiring harness routes power and signals between a refrigerator's control components and electrical devices, restoring reliable electrical connections for operation and controls. It replaces a damaged or broken harness to help regain normal appliance function. What it does:

• Connects control board, sensors, lights, and other electrical components to provide power and signal paths
• Replaces frayed, burnt, or damaged wiring that can cause intermittent or complete loss of function
• Helps resolve symptoms such as lights or dispenser not working, erratic controls, or failure of specific features tied to wiring
• Restores proper connector fit and secure electrical contacts when original harness pins or wires are compromised

• One wiring harness as shown

• Always disconnect power to the appliance before starting any repair
• Match connector shapes and wire colors to the original harness; route along original paths and secure with clips or ties
• Inspect mating connectors and control board terminals for damage before installing the new harness

This is a radiant bridge surface element that provides heat across an elongated cooking zone on a glass cooktop, ideal for griddles or oblong cookware. It operates at 1800 or 2600 watts depending on the selected setting. Replace this element if the bridge zone fails to heat, heats unevenly, or does not respond to temperature adjustments.

Main electronic control board for electric cooktops. Manages user interface and appliance functions. Replace if board is damaged, burnt, or unresponsive.