Electrolux Range Heating Element

This genuine oven bake element heats the oven cavity for baking and roasting, restoring proper cooking temperatures and consistent results. Replaces a damaged or non-heating bake element to bring your oven back to service. What it does:

• Heats the oven cavity so food reaches and holds set temperatures
• Restores even baking and roasting when the oven fails to heat
• Replaces elements that show visible damage, burn-through, or no glow
• Works with electric ovens that use a separate bake heating element

• Disconnect power to the appliance at the breaker before starting work
• Handle the element carefully to avoid bending or damaging terminals
• Remove oven racks and access the element from inside the oven
• Verify proper fit and secure mounting; tighten terminal fasteners firmly and restore power to test

This round surface heating element replaces a damaged or nonworking cooktop element to restore a stove's cooking zone. It delivers direct heat for pots and pans and is designed to fit the matching element receptacle. What it does

• Heats cookware on a stove top burner so pots and pans reach cooking temperatures.
• Restores heating to a single cooktop zone when the original element is cracked, burnt out, or intermittently working.
• Works with the oven's surface element control and wiring to provide regulated heat.
• Safe, standard replacement for the matching element — does not include controls or wiring unless listed.

• One round surface heating element (exact terminals and mounting hardware vary by model; only the item listed ships).

• Disconnect power to the appliance at the breaker before attempting replacement.
• Compare terminals and mounting style to the removed element to fit before installation.
• If wiring or control issues are suspected, test or replace associated components (switches, harness) rather than only the element.

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This bake element heats the oven cavity so your range can reach and maintain baking temperatures for cooking and roasting. Replaces a worn or damaged oven element to restore consistent oven heating. What it does:

• Heats the oven interior during bake cycles to cook food evenly
• Restores expected oven temperature when a faulty element prevents heating
• Helps eliminate uneven baking or no-heat symptoms caused by a broken element
• Visible signs to watch for: blistering, breaks, or burn marks on the element

• One bake (oven) heating element

• Disconnect power to the appliance at the breaker or unplug before servicing
• Handle the element carefully to avoid bending or damaging terminals
• Verify correct part fit and terminal type for your model before installation

This oven bake element heats the cavity to cook and brown food reliably. It replaces a worn or broken heating element so your oven can reach cooking temperatures again. What it does:

• Heats the oven for baking, roasting and broiling steps
• Restores proper oven temperature when the element is visibly damaged or not glowing
• Helps eliminate undercooked or unevenly baked food caused by a failed bake element
• Works as the main lower heating source in electric ovens that use separate bake and broil elements

• Always disconnect power at the breaker or unplug the appliance before starting work
• Typical install requires accessing the oven interior and securing the element with screws; support the element when disconnecting wires
• Use proper wire connectors and confirm tight, correct connections before restoring power

This oven lower bake element is the heating element that warms the oven cavity for baking and roasting. It restores proper baking heat so food cooks evenly and reaches set temperatures. What it does:

• Generates heat for the oven's bake function to cook and brown food
• Commonly causes no-heat or weak-heat oven symptoms when failed
• Can cause uneven baking or longer preheat times if damaged
• May show visible breaks, burn spots, or arcing when defective

• Disconnect electrical power to the appliance before starting any work
• Handle carefully and avoid bending the element; use gloves to protect hands
• Verify proper wire connections and secure mounting during reassembly

This is a range element assembly that's used in select electric ranges. It creates an electromagnetic field to help transfer energy to heat the food. Another name for this piece is an induction coil. If it is not working properly, it could prevent the burner from heating, rendering it useless.Although the range element can last for a long time, it will start to wear out and will break with extended use. Like other parts on the range, it could be damaged if the stove is moved and dropped.Unplug the range before replacing it.This range element assembly fits certain models from Frigidaire, Electrolux, and Kenmore. This piece is a genuine OEM replacement part sourced from the manufacturer. It is sold individually.

This bake element is the oven's main heating element that provides consistent heat for baking and roasting. Replacing a failed element restores proper oven temperature and cooking performance. What it does:

• Heats the lower oven cavity for baking and roasting cycles.
• Common symptom: oven does not heat or reaches lower-than-set temperatures.
• Common symptom: uneven baking or food undercooks on all racks.
• Also check for visible damage, burn marks, or broken connectors.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Allow the oven to cool fully before accessing the interior; wear gloves to protect against sharp edges.
• Remove the oven cavity access panel or back panel as required to access element mounting screws and wiring.
• Verify wiring connections are secure and test the element for continuity with a multimeter before final reassembly.