Electrolux Refrigerator Cap Or Cover

This cover assembly replaces a damaged or missing cover on your appliance, protecting internal components and restoring a clean, finished appearance. Use it when the original is cracked, loose, or no longer secures properly.

• Shields internal parts from debris, spills, and accidental contact
• Helps keep components enclosed and aligned for reliable operation
• Restores the appliance's finished look after damage or wear
• Common signs of failure: cracks, broken or missing tabs, discoloration, rattling, or a cover that won't stay in place

• Disconnect power before servicing; shut off water supply if working near water connections
• Remove retaining screws or release tabs; note the orientation of the original cover
• Transfer and reuse original screws, clips, or seals if required
• Do not overtighten fasteners into plastic; ensure all tabs fully engage before testing

This is not a filter. Use this bypasss if don't want to use the PureSource 2 Water Filter WF2CB or the Pure Advantage Water Filter EWF2CBPA.

This plug covers the small factory test opening on an appliance cabinet or liner. Replacing a missing or damaged plug helps close the opening to maintain a better seal and restore a clean, finished appearance.

• Seals the factory test opening in the cabinet/panel
• Helps limit air and moisture infiltration through the hole
• Reduces condensation or frost forming around the opening
• Restores a finished look when the original cap is missing or damaged

• Disconnect power before servicing the appliance
• Clean and dry the opening area for proper fit
• Align and press the plug in by hand until it sits flush—do not force or enlarge the hole
• Avoid sharp tools or sealants that could damage the liner or insulation

This upper hinge cover fits the left-hand side and snaps over the top door hinge in a gray finish. It protects the hinge hardware and restores a clean, finished look when the original cover is cracked or missing.

• Conceals upper hinge hardware on the left side for a clean appearance
• Shields the hinge area from dust and minor spills
• Helps prevent snagging or damage to wires routed through the hinge area on some models
• Typical symptoms: broken, loose, or missing hinge cover

• Disconnect power to the appliance before servicing
• Remove any retaining screw(s) or release tabs from the old cover; keep original fasteners for reuse
• Align the new cover over the hinge and snap or secure into place
• Support the door before loosening fasteners

This refrigerator housing is the molded support used to mount and protect its associated components inside the appliance. Replacing a damaged housing restores a secure fit and proper alignment so parts stay in place and function correctly.

• Provides structural support and mounting points for the related controls/components
• Helps route air and/or wiring as designed by the manufacturer
• Restores proper alignment to reduce rattles, rubbing, or interference
• Symptoms can include cracked plastic, broken tabs, loose or sagging assemblies, or components that won't stay secured

• Disconnect power before servicing; shut off water as needed if working near dispenser/ice components
• Transfer sensors, wiring, controls, and hardware from the original housing unless new parts are supplied
• Reuse original screws/clips; avoid overtightening to prevent cracking
• Verify harness connections and clearances before restoring power and water

This evap coil cover protects the evaporator and helps direct airflow for more consistent cooling. It replaces damaged or missing covers to reduce frost buildup, keep debris away from the coil, and help prevent interior leaks. What it does:

• Shields the evaporator coil from ice, debris and accidental contact to protect coil fins.
• Helps channel airflow across the coil for improved cooling performance.
• Can reduce frost accumulation and related moisture or dripping symptoms.
• When cracked or missing, you may notice increased frost, water in the cabinet, or reduced cooling.

• Always disconnect power to the appliance before servicing.
• Remove interior liners or access panels to reach the evaporator; handle coil fins and insulation carefully.
• Reinstall any mounting clips, grommets, or insulation exactly as removed to maintain fit and sealing.

This upper hinge cover protects and conceals the appliance's top door hinge, restoring a finished appearance and preventing dirt buildup. Durable molded replacement designed to match the original fit and look. What it does:

• Covers the upper door hinge to protect moving parts from dust and debris
• Restores the appliance's finished appearance when the original cover is cracked or missing
• Helps prevent accidental contact with the hinge area for safer daily use
• Common symptom: damaged, cracked, or missing hinge cover that exposes the hinge

• Disconnect power to the appliance and open the door fully before beginning work
• Typically installs with a few screws or snap-fit tabs; save existing fasteners unless replacements are provided
• Handle the door and any glass panels carefully to avoid damage during removal/replacement

A replacement corner cabinet trim that restores the finished edge on the appliance cabinet and hides gaps for a cleaner look. Helps maintain the cabinet appearance and prevents debris buildup at the corner. What it does:

• Replaces a cracked, broken, or missing corner trim piece to restore the cabinet edge
• Covers gaps where two cabinet panels meet to improve appearance
• Helps reduce dirt and moisture accumulation in the corner area
• Stops rattling or catching caused by a damaged trim

• Service is generally simple; remove any nearby shelving or panels for access
• Fastens with the factory clip or screw method used on the model—retain original hardware and check alignment before final fastening
• Disconnect power to the appliance if needed to access fasteners near electrical components
• Wear gloves to protect hands from sharp sheet-metal edges during installation

This cover hinge secures and supports an appliance cabinet lid or top panel, allowing smooth opening and stable closure. Replaces a worn or broken hinge to restore proper lid alignment and reduce rattling or sagging. What it does:

• Provides a pivot point for the appliance cover or top panel to open and close smoothly
• Restores proper alignment when the lid or top is drooping or binding
• Helps eliminate rattling or unusual movement during use
• Supports safe, steady operation of the cover when accessing the appliance interior

• Basic mechanical skill and common hand tools required for removal and replacement
• Disconnect power and empty the appliance as needed before servicing for safety
• Keep screws and fasteners organized during disassembly for proper reassembly

This molded evaporator cover replaces the plastic trim that protects and directs airflow over the freezer evaporator; it helps maintain even cooling and keeps ice and debris away from the coil assembly. Fits the OEM mounting locations for a proper seal. What it does

• Protects the evaporator coil from loose food and debris that can impede airflow.
• Directs cold air through the freezer compartment for more consistent temperatures.
• Helps reduce frost build-up on the evaporator by maintaining proper airflow patterns.
• Restores proper fit and appearance where the original cover is cracked, warped, or missing.

• One evaporator cover

• Disconnect power to the appliance before starting any repair.
• Remove screws or fasteners holding the old cover; handle tabs carefully to avoid breaking mounting clips.
• Defrost and dry the area if there is ice buildup before installing the new cover.
• Reassemble panels and verify there are no gaps that could allow air leaks or contact with moving components.

This upper hinge cover protects and finishes the refrigerator door hinge area on the right side, restoring appearance and helping keep hinge components free of dust and debris. Designed as a direct replacement for the OEM right-side hinge cover. What it does:

• Covers the upper door hinge area to improve cosmetic appearance and hide hardware
• Helps keep dust, crumbs, and moisture away from hinge components
• Prevents accidental contact with hinge edges while opening and closing the door
• Restores the original look after hinge repairs or replacements

• One upper hinge cover for the right (RH) side, gray

• Disconnect power to the appliance or unplug before servicing to prevent electrical hazards
• Handle carefully to avoid scratching the finish; align clip/fastener locations before snapping into place

This bypass is a small electrical connector used to complete or reroute a circuit inside the appliance, restoring continuity so the unit can be tested or operated while diagnosing a faulty component. What it does:

• Provides a safe path to complete an electrical circuit when a component or sensor is removed for testing
• Helps verify whether a control or subsystem is causing an interruption in power or signal
• Can be used temporarily to isolate faults and confirm repairs
• Resolve symptoms like intermittent operation or no-response from a circuit while troubleshooting

• Disconnect all power to the appliance before installing to avoid shock or damage
• Intended for diagnostic or temporary use; replace failed components with correct OEM parts for permanent repair
• Follow the appliance wiring diagram and manufacturer's instructions
• Ensure secure, insulated connections to prevent short circuits

This evaporator coil cover protects the refrigerator's evaporator assembly and helps direct airflow for more consistent cooling. It replaces a damaged or missing interior cover to keep the coil shielded and the compartment operating as intended. What it does:

• Shields the evaporator coil from contact and debris to prevent accidental damage
• Helps direct cold air across the evaporator for more even cooling performance
• Reduces unwanted airflow patterns that can cause frost buildup or uneven temperatures
• Covers sharp edges on the evaporator assembly for safer access during service

• One evaporator coil cover

• Disconnect power to the appliance before beginning any repair
• Remove interior panels and shelves as needed to access the evaporator area
• Handle the evaporator and cover carefully to avoid bending fins or damaging nearby components
• Fully defrost the evaporator before installing the new cover