Electrolux Cap Or Cover

Transparent glass shelf for refrigerator food storage. Replace if cracked, broken, or shattered from heavy loads or accidental drops. Direct fit part.

This cover assembly attaches to the back or bottom of the refrigerator to enclose and protect the compressor and related components. It helps keep dust and debris away from the compressor area while providing a finished appearance. Replace this cover if it is cracked, broken, or missing, which can allow dirt buildup on the compressor and condenser that reduces cooling efficiency.

Replacement glass panel for refrigerator shelves. Restores a smooth surface when original is cracked, broken, or missing. Fits shelf assemblies.

This cover fits over the lint screen opening on the top or front of the dryer, serving as a protective grille that allows airflow while keeping the lint filter accessible. It snaps or screws into the dryer housing and helps direct air through the lint screen properly. Replace this part if it is cracked, broken, or missing, which can allow lint to bypass the filter and reduce drying efficiency.

Bypass cap replaces water filter when using external filtration or no filter needed. Allows ice maker and water dispenser to function normally.

This replacement cover restores the protective barrier and finished look of the original part. It shields the underlying assembly from dust and accidental contact, helping maintain safe operation and a clean, factory appearance.

• Provides a protective barrier over the designated opening or component
• Helps maintain proper airflow/enclosure integrity as designed
• Secures with existing tabs or screws for a stable fit
• Typical signs of failure: cracked or missing cover, broken tabs, loose/rattling panel, visible damage

• Disconnect power before service; for laundry appliances, also shut off water and gas
• Wear gloves; retain and reuse original screws/clips unless new hardware is supplied
• Note orientation before removal and transfer any clips, seals, or trim from the old cover
• Seat fully and avoid overtightening; verify clearances before restoring power

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Molded support housing that mounts and protects internal refrigerator components. Replace if cracked, broken, or damaged to restore secure fit and alignment.

The lint filter grill is the frame or housing that holds the lint screen in place within the dryer's air circulation system. Located inside the dryer door or top panel, it ensures proper airflow while capturing lint particles. Replace if the grill is cracked, warped, or no longer securely holds the lint filter screen.

This evap coil cover protects the evaporator and helps direct airflow for more consistent cooling. It replaces damaged or missing covers to reduce frost buildup, keep debris away from the coil, and help prevent interior leaks. What it does:

• Shields the evaporator coil from ice, debris and accidental contact to protect coil fins.
• Helps channel airflow across the coil for improved cooling performance.
• Can reduce frost accumulation and related moisture or dripping symptoms.
• When cracked or missing, you may notice increased frost, water in the cabinet, or reduced cooling.

• Always disconnect power to the appliance before servicing.
• Remove interior liners or access panels to reach the evaporator; handle coil fins and insulation carefully.
• Reinstall any mounting clips, grommets, or insulation exactly as removed to maintain fit and sealing.

Covers and secures the cabinet hinge on your refrigerator. Replaces a cracked, broken, or missing cover to restore a clean appearance and protect the hinge.

Restores the finished edge on your refrigerator cabinet and hides gaps. Replaces cracked, broken, or missing corner trim for a cleaner appearance.

Refrigerator cover that installs to protect internal components or provide a finished appearance. Replace if cracked, broken, or missing for proper coverage.

Protective cover that shields the refrigerator motor assembly. Replace if your cover is cracked, broken, or missing to protect internal components.

Water valve cap for side-by-side refrigerators. Covers and protects the water inlet valve connection. Replace if cracked, broken, or missing.

Molded plastic evaporator cover that protects the freezer coil assembly and directs airflow. Replace if cracked, broken, or missing for proper cooling.