Electrolux Refrigerator Hinge Parts

This hinge bearing supports the freezer door on the hinge pin so it swings smoothly and stays aligned. Replacing a worn bearing can stop scraping or sagging and help restore proper door movement and sealing.

• Provides a low-friction surface between the hinge pin and door
• Helps maintain correct door height and alignment for a reliable seal
• Wear symptoms include squeaking/scraping, door drop or wobble, and difficulty closing
• Replace if the original bearing is cracked, flattened, or missing

• Disconnect power and remove items from the freezer door before starting
• Support the door; remove hinge cover and fasteners, then lift the door off the hinge pin
• Slide the old bearing off the hinge pin and install the new bearing in the same orientation
• Reassemble, then check door alignment and gasket contact; adjust as needed

This door hinge bearing fits the refrigerator door hinge and provides a smooth, low-friction pivot point. Replacing a worn bearing restores smoother door movement and helps maintain proper alignment and a reliable gasket seal. What it does:

• Provides a low-friction surface between the hinge pin and door
• Helps keep the door aligned for consistent gasket contact
• Reduces squeaks, scraping, or binding during opening and closing
• Helps with symptoms like door sagging, not closing fully, or uneven sealing

• 1 hinge bearing

• Disconnect power and remove items from the door before servicing
• Support the door; remove hinge cover and fasteners, then lift the door off the hinge pin
• Replace the bearing in the same orientation; reassemble hardware securely
• Reinstall the door and ensure smooth swing and full gasket contact around the perimeter

Used on fresh food and freezer doors.

This hinge bracket supports and aligns the refrigerator door at the pivot point, helping the door open and close smoothly and seal properly. Replacing a worn bracket can restore stable door movement and reduce air leaks.

• Provides rigid support for the door hinge to maintain proper alignment
• Helps ensure a consistent door seal to prevent temperature fluctuations
• Common fix for loose, sagging, or misaligned doors
• Helps if the door makes popping/grinding noises when opening or closing

• Unplug the refrigerator and wear cut-resistant gloves
• Support the door before removing hinge fasteners to prevent drops
• Transfer and reinstall existing screws/hinge pin as needed
• Check door alignment and gasket contact after installation

This lower hinge bracket supports and aligns the refrigerator door at the bottom pivot point. Replacing a bent or worn bracket restores smooth door movement and proper alignment so the door opens and closes without rubbing or sagging.

• Provides the mounting point for the lower hinge/pin at the cabinet base
• Keeps the door square and aligned for smooth opening and closing
• Common fix for door sagging/drooping or rubbing at the bottom corner
• Helps eliminate scraping, binding, or squeaking from a damaged hinge area
• Replaces cracked, bent, or stripped brackets

• Disconnect power and remove items from the door to reduce weight.
• Support the door; remove the bottom hinge cover and screws, then lift the door off the lower hinge pin.
• Remove the old bracket, transfer any reusable hardware/shims, and install the new bracket securely.
• Reinstall the door, check gaps and gasket contact, adjust as needed, and restore power.

This refrigerator dispenser bearing supports the auger shaft so it spins smoothly during ice dispensing. Replacing a worn bearing restores quieter, more reliable ice delivery and helps prevent binding or uneven crushing of cubes. What it does

• Supports and centers the ice auger/crusher shaft inside the ice bucket
• Reduces friction to allow smooth, consistent rotation
• Wear can cause grinding or squealing during dispensing
• Symptoms include slow/no ice dispensing, jamming, or intermittent operation

• 1 bearing

• Disconnect power and turn off the water supply before service
• Remove the ice bucket and disassemble the crusher housing to access the bearing
• Note the bearing's orientation; transfer any spacers or clips as found
• Reassemble carefully and ensure the auger turns freely by hand before restoring power

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.

Lower hinge secures the bottom corner of a refrigerator door and provides a durable pivot for smooth opening and closing. Replacing a worn hinge restores proper door alignment and helps maintain a tight seal. What it does:

• Supports the weight of the lower door corner and provides a pivot point for opening/closing.
• Keeps the door aligned so the gasket can seal properly.
• Worn or damaged hinges can cause door sag, uneven gaps, rubbing, or difficulty closing.
• Restoring a solid hinge reduces stress on the door and latch for more reliable operation.

• Disconnect power to the appliance and remove food/items from the door before starting.
• Always support the door while removing/installing the hinge to prevent dropping or damage.
• Use the correct tools and hardware; tighten fasteners snugly but avoid over-torquing.
• After installation, check door alignment and seal; adjust as needed for proper operation.

This lower hinge bracket mounts at the bottom of the cabinet to support and align the refrigerator door. Replacing a bent or worn bracket helps restore smooth door operation and a consistent gasket seal to help reduce air leaks.

• Provides the mounting base for the lower hinge/pin at the bottom of the cabinet
• Supports the door's weight to keep it level and properly aligned
• Helps the door open and close smoothly without scraping or binding
• Typical symptoms: door sagging or misalignment, difficulty closing, gaps at the gasket, squeaks/scraping near the lower hinge, or visible bracket damage

• Disconnect power; remove items from the door and support the door to prevent dropping
• Mark hinge/bracket locations for alignment; remove bottom hinge cover and mounting screws
• Transfer hinge pin and any spacers from the old bracket if applicable; install the new bracket and tighten screws securely
• Rehang and align the door; confirm full gasket contact and smooth door swing

Replace the worn bearing that supports your refrigerator's ice-dispenser auger. This bearing helps the auger spin smoothly so cubes travel to the chute, restoring steady ice dispensing and reducing grinding or jamming.

• Supports the auger shaft within the ice bin/dispenser assembly
• Enables smooth rotation to move ice toward the chute
• Wear can cause slow or failed dispensing and squealing/grinding noises
• Fixes issues with a cracked, worn, or seized auger support

• Disconnect power and remove the ice bin before servicing
• Separate the bin front/cover and auger assembly; note the bearing's orientation
• Transfer the new bearing and reuse existing screws/retainer if present
• After reassembly, confirm the auger turns freely by hand before restoring power

This refrigerator bracket is the OEM mounting piece that secures a specific internal assembly in place. Replacing a cracked or missing bracket restores a solid fit, proper alignment, and smooth, rattle-free operation of the attached component.

• Provides a rigid mounting point for the designated refrigerator component
• Maintains proper alignment to help the assembly operate correctly
• Helps reduce vibration and movement that can cause noise or wear
• Typical signs of failure: broken tabs, stripped holes, loose or misaligned parts

• Disconnect power; turn off water supply if working near ice/water components
• Access the area per your product's diagram; retain and reuse existing screws/fasteners
• Transfer any clips, spacers, or grommets from the old bracket to the new one
• The mounted component seats fully and operates before reassembling panels/shelves

This bearing supports a rotating shaft to reduce friction and restore smooth, quiet operation. It replaces a worn bearing to help stop grinding, wobbling, or noisy rotation in the appliance. What it does

• Supports and centers a rotating shaft or drum to reduce friction and wear.
• Allows smoother rotation to reduce noise such as grinding, squealing, or rumbling.
• Helps prevent wobble or uneven rotation that can stress other components.
• When worn, can cause vibration, excess noise, or difficulty maintaining proper rotation speed.

• Disconnect power (and water, if applicable) before starting any repair.
• Handle bearings and shafts carefully; keep parts clean and free of debris during installation.
• Use appropriate pullers/press or follow OEM instructions to remove/install; improper tools can damage the part.
• If other wear is present (seals, shafts, supports), inspect and replace as needed.

This lower hinge secures and pivots a refrigerator door, restoring proper alignment and smooth opening. It helps stop door sag, uneven sealing, and rubbing that can cause cold loss or noisy operation. What it does:

• Provides a durable pivot point for the refrigerator door to open and close smoothly
• Restores correct door alignment to improve the door seal and cooling performance
• Stops door sag, rubbing against the cabinet, and uneven gaps that can lead to air leaks
• Helps reduce noise from a misaligned or worn hinge

• Support or remove the door before replacing the hinge to avoid injury or damage
• Keep fasteners and any hinge shims or bushings; reuse only if in good condition or replace with OEM parts
• Tighten mounting screws securely and check door alignment; minor shimming may be required

This lower door hinge restores proper pivot and alignment so a refrigerator or freezer door opens and closes smoothly. It replaces a worn or damaged hinge to reduce sagging and improve the door seal. What it does:

• Supports the bottom of the appliance door and provides the pivot point for opening and closing
• Corrects door sag, uneven gaps, and misalignment that can prevent the door from sealing
• Reduces rubbing, catching, or scraping when the door moves
• Helps maintain proper door alignment to protect the gasket and improve cooling efficiency

• One lower door hinge

• Always unplug the appliance or disconnect power before beginning repairs
• Support the door fully before removing hinge fasteners; door may be heavy—use a second person or support stand
• Keep track of mounting hardware and any shims/plates for reassembly; tighten screws securely but do not overtighten