Electrolux Washer Dryer Combo Parts

Wiring harness for laundry center units. Connects electrical components inside the cabinet. Replace if wires are frayed, damaged, or corroded.

Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

This is a small C-clip or retainer ring that secures the idler pulley to its bracket on a laundry center. It keeps the pulley in place so the drive belt maintains proper tension against the drum. Replace this ring if the idler pulley has come loose, the drum belt slips or falls off, or the dryer drum does not spin properly.

This is a 10-16 x .312 sheet-metal screw with a quad-style panel head used to secure appliance panels and trim. It replaces missing or damaged screws to help stabilize panels and reduce rattling. What it does:

• Fastens control panels, trim pieces, and thin sheet-metal components
• Restores secure fit where screws are missing or stripped
• Helps stop panel vibration, rattling, or misalignment caused by loose fasteners
• Small, common mounting screw for interior and exterior appliance panels

• One 10-16 x .312 quad panel head screw (quantity: 1)

• Disconnect power to the appliance before working on panels or controls
• Use the correct screwdriver head to avoid stripping the quad head
• Tighten by hand; do not overtighten to prevent stripping or cracking panels
• Keep extra screws on hand; replace any that are corroded or damaged

This round on/off switch replaces the worn or broken power control on compatible appliances, restoring reliable on/off operation and user control at the front panel. Designed to match OEM fit and function for direct replacement. What it does:

• Provides a simple on/off user control for the appliance's power circuit
• Re-establishes consistent electrical contact when the original switch fails
• Commonly fixes symptoms like no power from the control location, intermittent power, or a switch that won't stay on
• Operates as the primary user-actuated power control for the associated circuit

• One round on/off switch

• Disconnect power to the appliance before testing or replacing the switch to avoid shock
• Verify correct wiring location and connectors before removing the old switch; transfer any wiring harness or connectors exactly
• Handle with care to avoid damage to the switch actuator or mounting tabs

This is a rubber hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. Over time this hose can crack, clog, or develop leaks. Replace it if you notice detergent not reaching the tub, water leaking near the dispenser area, or visible deterioration of the hose.

Spring retainer for washers and laundry centers. Secures internal springs in place. Replace if cracked, broken, or missing to restore proper assembly.

Flat washer used to secure components in washers, dryers, and laundry centers. Replace if washer is missing, bent, or corroded during repairs.

Replace your washer's 3/8 inch lock washer. Secures internal components and hardware connections. Order a new one if bent, missing, or worn out.

Secures hoses on your washer to prevent leaks and water damage. Replace if loose, cracked, or during hose repairs. Verify fit with your model number.

Lower spring tub sleeve for washers. Protects and guides the suspension spring connection to the tub. Replace if cracked, worn, or missing.

Upper spring tub sleeve for washers. This bushing cushions the suspension spring connection to the tub. Replace if worn, cracked, or missing.

This latch secures the detergent or fabric softener dispenser drawer on a front-load washing machine, keeping it firmly closed during the wash cycle. It clicks into place to hold the drawer shut and releases when pressed to allow access to the dispenser compartments. Replace this latch if the dispenser drawer will not stay closed, pops open during a cycle, or if the latch mechanism is cracked or broken.