Electrolux Washer fills slowly or will not fill at all: Common Causes & How to Fix

Repair Instructions:

Once you've made sure that the water inlet valve is getting power and working as it should, it's time to check if the Electrolux washer tub is spinning during the spin cycle. If it's not, the issue might be with the lid switch assembly, which could be preventing the tub from filling correctly. To find out if the lid switch assembly is the problem, you can use a multimeter to test the lid switch and see if it has continuity, which means it's making a proper electrical connection. If the lid switch doesn't have continuity it will need to be replaced.

How to Replace Washing Machine Lid Switch Assembly

1. Unplug the washing machine. Disconnect the machine from the power source. This will prevent electric shock.

2. Open the lid. Prop the washing machine lid fully open.

3. Locate the switch. The lid switch assembly is on the front panel of the Electrolux washer. Identify the specific location.

4. Remove switch mounting screws. Use a screwdriver to detach any screws securing the switch assembly.

5. Disconnect wiring. Carefully disconnect the wiring harness or connectors attached to the switch.

6. Remove switch assembly. With the screws and wiring detached, you can now fully remove the lid switch assembly.

7. Install new switch. Carefully align the new lid switch assembly into the opening on the Electrolux washer front panel.

8. Reconnect wiring. Attach the wiring harness or connectors to the corresponding terminals on the new switch.

9. Remount the switch. Insert and tighten the mounting screws to secure the new lid switch assembly in place.

10. Test operation. Plug in the Electrolux washer and open/close the lid to verify proper switch operation before regular use.

11. Reattach panel. If accessing from inside the cabinet, reattach the metal panel covering the lid switch assembly.

12. Restore power. Plug the washing machine back in and make sure it is functioning properly.

Repair Instructions:

The water inlet valve in your washing machine is responsible for letting water flow into it. When this valve isn't working properly, it can lead to a slow or even no water filling in your washing cycle. The water inlet valve needs a good amount of water pressure. Start by checking if your water pressure is enough to make it work correctly. If your water pressure is okay but the washing machine still fills up slowly, it's a good idea to clean the screens found inside the hose connections and on the water inlet valve. If, after this, your Electrolux washer is still not filling up as it should, the best course of action is to replace the water inlet valve. This will help your washing machine function properly and fill with water at the right pace.

How to Replace Washing Machine Water Inlet Valve

1. Shut off water supply. Turn off the valves where the water lines attach to the washing machine. This prevents flooding during repairs.

2. Release water pressure. Run the wash cycle to drain any remaining water trapped in the lines before proceeding.

3. Disconnect hoses. Detach the hot and cold water hoses from the valve itself using pliers if necessary.

4. Remove mounting hardware. Use a screwdriver to take out any screws or bolts attaching the inlet valve to the machine.

5. Extract old valve. Ease the inlet valve out of position once it is fully detached from mountings and water lines.

6. Inspect seal rings. If the rubber seal rings inside the valve port are cracked or deteriorated, replace them now.

7. Install new valve. Position the replacement inlet valve where the old one sat, aligning holes for mounting hardware.

8. Reattach securely. Replace all mounting bolts or screws removed earlier to fasten the new valve firmly in place.

9. Reconnect water lines. Attach the hot and cold water supply hoses to the new inlet valve ports using pliers if needed.

10. Restore water supply. Turn on valves to refill lines and test connections for leaks before operating.

Repair Instructions:

The control board in your washing machine is like its command center, responsible for sending power to various electrical parts, including the inlet valve that lets water into the tub. If this board is faulty, it might not provide the necessary power to open the inlet valve, which means the Electrolux washer won't fill with water properly. To check if the control board is the issue, you can look for signs of damage, like burning or damaged components. You can use a multimeter to check if the inlet valve is getting power by referring to the appliance's wiring diagram. If there's no power during the fill cycle, it's likely that the control board is malfunctioning, and you would need to replace that board.

How to Replace Washing Machine Control Board

1. Unplug the washing machine. Disconnect the power cord before servicing to prevent electric shock.

2. Open the control panel. The control board is located behind the control panel on the Electrolux washer front.

3. Label connections. Take note of where each wire and connector is attached to the control board.

4. Disconnect wires. Carefully detach all wiring harnesses and connectors from the board.

5. Remove mounting screws. Use a screwdriver to remove any screws securing the control board.

6. Remove control board. Carefully pull the control board free from the Electrolux washer once all wires are detached.

7. Install new control board. Align the replacement board into position and insert mounting screws.

8. Reconnect wires. Attach all wiring harnesses and connectors to the matching terminals on the new board.

9. Close control panel. Carefully close the control panel once the new board is installed.

10. Restore power. Plug in the washing machine and test operation.

11. Program control board. You may need to program or configure the new control board if it doesn't operate correctly.

12. Test cycles. Run short test cycles to verify the Electrolux washer is functioning properly before regular use.

Repair Instructions:

The washing machine's pressure switch has a tube that's connected to the side or bottom of the tub. As water flows into the tub, it pushes air into the tube, increasing air pressure. This increase triggers the pressure switch to cut off power to the water inlet valve, stopping the water flow once the tub is adequately filled. If the pressure switch isn't working correctly, it can prematurely shut off the power to the inlet valve, resulting in the Electrolux washer not filling up properly. To check if the pressure switch is doing its job, you can follow the appliance's wiring diagram to identify the switch's terminals. Use a multimeter to test the pressure switch for continuity. When you blow into the tube attached to it, you should see the continuity either interrupted or restored. If this doesn't happen, it's a sign that the pressure switch is faulty and should be replaced.

How to Replace Washing Machine Pressure Switch

1. Shut off water. Turn off the water supply valves located where the water hoses attach to the washing machine. This prevents water from escaping during the repair.

2. Release water pressure. Run the washing machine through a spin cycle to drain any remaining water from the hoses and pump.

3. Detach hoses. Disconnect the hoses from both the water inlet and outlet ports of the old pressure switch. You may need an adjustable wrench.

4. Locate switch. Find the pressure switch, usually mounted on the back, side or bottom of the washing machine cabinet. It will have labeled ports for hose connections.

5. Remove switch. Unscrew any mounting bolts, nuts or screws to detach the old pressure switch from the machine housing. Remove the switch completely.

6. Install new switch. Line up the replacement pressure switch and hand-tighten the mounting hardware to secure it in the same position.

7. Reconnect hoses. Firmly push the hoses onto the corresponding ports of the new pressure switch. Ensure there are no leaks.

8. Restore water supply. Turn the water valves back on and check for leaks at the hose connections before running a test cycle.

Repair Instructions:

The main control board of a washing machine sends power to all the electrical parts, including the inlet valve that lets water in. If this board isn't working properly, it might not send power to the inlet valve, and that means your machine won't fill with water. You can check the control board for signs of burning or damaged parts. Another way to test it is by using a multimeter. You can follow the washing machine's wiring diagram to check if the inlet valve is getting power. During the fill cycle, if you don't see any power, there's a good chance the control board is the problem. In that case, you'll need to replace it to get your washing machine working again.

How to Replace Washing Machine Main Control Board

1. Unplug the washing machine. Disconnect power to prevent electric shock.

2. Open control panel. Unscrew the control panel on the Electrolux washer to access interior.

3. Locate control board. The main control board is mounted to the cabinet interior.

4. Label wire connections. Note where each wire harness connects to the control board.

5. Disconnect wires. Detach all wire harnesses from the terminals on the control board.

6. Remove mounting screws. Use a screwdriver to remove screws securing control board.

7. Remove control board. Carefully detach old control board from the Electrolux washer.

8. Install new control board. Align replacement board and reinsert mounting screws.

9. Reconnect wires. Attach all wire harnesses to proper terminals on new control board.

10. Close control panel. Carefully close and screw the control panel back on.

11. Restore power. Plug in washing machine and test operation.

12. Program control board. You may need to program the new control board if needed.

Repair Instructions:

Make sure you select the right washing machine settings that match the type of clothes you're washing and the specific options you want. For instance, if you choose an "economy cycle," keep in mind that it will use only cold water. To make informed choices, consult the owner's manual for guidance. The manual provides valuable information on the various cycles and settings your washing machine offers, helping you achieve the best results for your laundry. This way, you can optimize your washing machine's performance and care for your clothes, making sure they come out clean and in great condition. Using the correct settings is a simple yet important step in achieving the desired outcome for your laundry.

Repair Instructions:

Water valves come with tiny filter screens to stop particles from causing blockages or even preventing the valve from closing. Some fill hoses also have screens where they connect to your home's hot or cold water shut-off valves. These screens need to be inspected and cleaned when necessary.

Repair Instructions:

Your home's water pressure could be the culprit. To make sure the water inlet valve operates as it should, it needs at least 20 pounds per square inch (psi) of water pressure. You can test the water pressure to see if it meets this requirement. If it falls short of 20 psi, it's likely causing the issue. Having the right water pressure is important for your washing machine fills up correctly. So, give your water pressure a check to make sure it's meeting the necessary level for your machine to function properly.