Parts for Yard Machines 31AM63FF752 / 2008: Engine Assembly 370 Sua Parts

This replacement part is a flywheel. This is a genuine replacement part made by MTD. This part is a large rotating piece, similar to a wheel, that provides the engine with rotational energy that is later converted to other types of energy so that the engine can operate smoothly. A new flywheel might be needed if the current one is missing or damaged. If the user hears unusual noises coming from inside the engine area, the flywheel might be out of place and not working properly. If this is the case, it might be best to replace this part. Be sure the engine is completely powered down and cooled off before repairing this part. This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This replacement part is a stud assembly. This is a genuine replacement part made by MTD. This stud assembly is responsible for keeping the muffler in place and secure so that the lawn mower may operate smoothly and according to the user's preferences. A new stud assembly might be needed if the current one is misplaced or damaged. It is not unusual for the studs to become stripped over time and need to be replaced. If the muffler is no longer able to stay in place, it can be due to the studs and should be looked into. Be sure the engine is completely turned off before attempting to replace this part. This stud assembly is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and dependable performance. Small but mighty, this component allows for increased conductivity and heat control. If the spark plug is damaged or in poor condition, many problems may arise in equipment, including sudden stop while running, overheating, and excessive gas consumption. Replace the spark plug by disconnecting the spark plug wire first, then use a socket driver or wrench to remove the spark plug. Install the new spark plug by turning it by hand initially to avoid cross-threading. If it doesn't twist anymore, use a deep socket wrench or socket driver to tighten the plug until snug. The spark plug can also be used to tune up outdoor power equipment or improve a small engine. This part is recommended to be replaced once per season. This part works with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and others with small engines. It is compatible with brands such as Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut. This is a genuine OEM part directly from the manufacturer and is sold individually.

This choke bracket is a genuine OEM part sourced directly from the manufacturer for use on snowblowers. The choke control bracket opens or closes the choke plate in the carburetor to help start the engine. The choke should be closed when getting it ready to work. Closing it shuts the air intake and keeps the gas mixture richer, which helps the engine fire up when it is cold. If the choke bracket is rusted or broken and is working, the choke may not work correctly. The engine may not start or may run roughly when it does start. If this happens, the choke bracket should be replaced.Before replacing the choke bracket, remove the spark plug and empty the gas from the snowblower. Wear safety gloves and safety glasses. Locate the choke and remove the screws holding it in place. Remove and discard it and install the new bracket. Use the screws from the original bracket to secure the bracket. Reinstall the fuel and spark plug. This choke bracket is a silver metal part that is sold individually; it does not come with screws or bolts. It is designed for use in snowblowers manufactured by Craftsman and MTD.

This genuine replacement part is an air filter heating cover for snowblowers. The air filter heating pipe cover is the plastic piece that covers the heating pipe of a snowblower. This cover is meant to protect the user from burning themselves on the heating pipe while using the machine. If the heating pipe cover is damaged to the point where it is no longer covering the heating pipe, it should be replaced. Thankfully, replacing this part is a simple process.To replace the heating pipe cover, locate the mounting screws that secure it to the snowblower. Before removing, make sure the engine has cooled to avoid getting burned. Once located, remove the mounting screws that attach the cover. Once removed, replace with the new cover and fasten the screws tightly. This OEM replacement part is sold individually and is compatible with MTD brand snowblowers.

This is a genuine replacement ignition key that is manufactured by MTD for use in select models of outdoor power equipment. The ignition key is a plastic piece that is inserted into the ignition cylinder to start the machine. Turning the plastic key will signal to the engine to fire. This is a durable plastic piece, but it can become damaged or lost over time, which will render the machine unable to start. Replacing it will be necessary in order to operate the unit. This genuine OEM ignition key is manufactured to exact standards. It can be used in snowblowers and snow throwers from MTD, Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. The durable plastic key is sold as an individual unit and does not require any tools for installation. This is a simple replacement that should only take a couple of minutes. In the event that the old key is damaged or stuck in the ignition, it may take more effort. It is important to disconnect the power supply for safety before performing any repairs, as well as to wear gloves for hand protection.

This throttle linkage spring is typically attached to the throttle cable, although it may be attached to the carburetor or the throttle body on select models. This spring will close the throttle valve, which helps reduce the fuel flow to the engine and helps to slow it down. The spring can become stretched or snap over time with regular use. A faulty throttle spring could be identified by the throttle sticking or lacking any control at all. This simple repair will require needle nose pliers, sockets, a screwdriver, and a wrench. Be sure to use gloves to perform all repairs and use caution when replacing the throttle spring to prevent damage to the new part. This OEM throttle spring is designed for use with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and other small engines in lawn care equipment. It is compatible with more than 150 models and a number of brands, including Troy-Bilt, Husky, Yard-Man, MTD, Yard Machines, and Cub Cadet.

The governor rod is a genuine replacement part found on select models of snowblowers. This rod is responsible for connecting the throttle cable and throttle body, helping to open and close the throttle to change the speed of the engine. This durable metal rod is exposed to repetitive motion and constant vibrations, which can cause damage or wear over time. If this rod does not function, the throttle will be unable to be controlled and that can affect the use of the equipment. Replacing the governor rod with this genuine part will guarantee an exact fit for compatible units. This genuine governor rod is manufactured to specific OEM standards and can be used in compatible machines from Cub Cadet, MTD, Yard Man, Craftsman, Troy-Bilt, Yard Machines, and HUSKEE. The part can be found in snowblowers, with hundreds of possible models that can take this governor's rod. It is made of durable metal and sold as an individual unit. No additional components or hardware are included, and any additional parts will require a separate purchase. Always wear gloves and perform engine repairs only when the machine has had time to cool. Be sure to disengage the engine before doing any work for safety, as well.

This replacement part is a push rod kit. This is a genuine replacement part made by MTD. This part is commonly found in certain types of lawn mowers and assists the user in maneuvering the machine in the desired direction.A new push rod kit might be needed if the current one is damaged in any way. This might include being bent, dented, cracked, or chipped. If this is the case, the rod might not be able to function properly and should be replaced so that the appliance can return to working order. Be sure the engine is powered down before attempting to replace or repair this part in any way. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

The purpose of the fuel nipple in a small engine is to clean the fuel before it reaches the carburetor. If the fuel is dirty, it could cause issues with the carburetor and other parts of the engine. If the engine misfires, has a fuel odor, leaks, or has problems with dirty fuel getting into the carburetor, it may be time to replace the fuel nipple. It is an easy replacement, but be sure to work in a well-ventilated area. Drain the fuel tank and disconnect the spark plug before beginning this repair. This OEM fuel nipple is a genuine part right from the manufacturer. This fuel nipple can work well for snowblowers, snow throwers, chippers, tillers, and log splitters. It is compatible with a range of models from brands like Craftsman, Yard Machines, Yard-Man, MTD, and Troy-Bilt.

The flywheel key keeps the engine flywheel and the crankshaft connected. In the event that the engine is forced to a sudden stop, the flywheel key could be sheared off, making it impossible for the engine to start back up again. Replacing the flywheel key is a part of routine maintenance for many modern engines, so it should be inspected and replaced as needed. This sturdy metal flywheel key is easy to install, but remember to choose the right torque setting when doing the replacement. Always disengage the spark plug and wear gloves when replacing engine parts. This genuine flywheel key is designed to be used in a number of lawn and garden equipment products from MTD, Troy-Bilt, Yard Machines, Cub Cadet, Yard-Man, Husky, and Bolens. It can be used as a replacement for many models of snowblowers, lawnmowers, and log splitters. Sold individually.

The fuel line is used to carry fuel through the machine, and it must be in good condition. As fuel line parts age, they are prone to damage. In some cases, they might crack, which could result in a fuel leak. Other times, the ends of the tube might not fit properly, even when they are clamped down. Eventually, the fuel line will need to be replaced. This is a relatively simple job, which will require only a pair of pliers to complete. This replacement fuel line kit is sold individually. This OEM kit will include the rubber tube as well as two metal clamps for attaching the line to the machine. The fuel line may be used with snowblowers, lawnmowers, tillers, leaf blowers, log splitters, wood chippers, and other small engines, It will work with machines from many different brands, including MTD, Yard Machines, Troy-Bilt, Yard-Man, Bolens, Cub Cadet, and Husky.