Parts for Columbia 31AM63K2597 / 2008: Engine Assembly Parts

This replacement part is a flywheel. This is a genuine replacement part made by MTD. This part is a large rotating piece, similar to a wheel, that provides the engine with rotational energy that is later converted to other types of energy so that the engine can operate smoothly. A new flywheel might be needed if the current one is missing or damaged. If the user hears unusual noises coming from inside the engine area, the flywheel might be out of place and not working properly. If this is the case, it might be best to replace this part. Be sure the engine is completely powered down and cooled off before repairing this part. This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This replacement part is a stud assembly. This is a genuine replacement part made by MTD. This stud assembly is responsible for keeping the muffler in place and secure so that the lawn mower may operate smoothly and according to the user's preferences. A new stud assembly might be needed if the current one is misplaced or damaged. It is not unusual for the studs to become stripped over time and need to be replaced. If the muffler is no longer able to stay in place, it can be due to the studs and should be looked into. Be sure the engine is completely turned off before attempting to replace this part. This stud assembly is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and dependable performance. Small but mighty, this component allows for increased conductivity and heat control. If the spark plug is damaged or in poor condition, many problems may arise in equipment, including sudden stop while running, overheating, and excessive gas consumption. Replace the spark plug by disconnecting the spark plug wire first, then use a socket driver or wrench to remove the spark plug. Install the new spark plug by turning it by hand initially to avoid cross-threading. If it doesn't twist anymore, use a deep socket wrench or socket driver to tighten the plug until snug. The spark plug can also be used to tune up outdoor power equipment or improve a small engine. This part is recommended to be replaced once per season. This part works with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and others with small engines. It is compatible with brands such as Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut. This is a genuine OEM part directly from the manufacturer and is sold individually.

This genuine replacement part is an air filter heating cover for snowblowers. The air filter heating pipe cover is the plastic piece that covers the heating pipe of a snowblower. This cover is meant to protect the user from burning themselves on the heating pipe while using the machine. If the heating pipe cover is damaged to the point where it is no longer covering the heating pipe, it should be replaced. Thankfully, replacing this part is a simple process.To replace the heating pipe cover, locate the mounting screws that secure it to the snowblower. Before removing, make sure the engine has cooled to avoid getting burned. Once located, remove the mounting screws that attach the cover. Once removed, replace with the new cover and fasten the screws tightly. This OEM replacement part is sold individually and is compatible with MTD brand snowblowers.

This is a genuine replacement ignition key that is manufactured by MTD for use in select models of outdoor power equipment. The ignition key is a plastic piece that is inserted into the ignition cylinder to start the machine. Turning the plastic key will signal to the engine to fire. This is a durable plastic piece, but it can become damaged or lost over time, which will render the machine unable to start. Replacing it will be necessary in order to operate the unit. This genuine OEM ignition key is manufactured to exact standards. It can be used in snowblowers and snow throwers from MTD, Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. The durable plastic key is sold as an individual unit and does not require any tools for installation. This is a simple replacement that should only take a couple of minutes. In the event that the old key is damaged or stuck in the ignition, it may take more effort. It is important to disconnect the power supply for safety before performing any repairs, as well as to wear gloves for hand protection.

This throttle linkage spring is typically attached to the throttle cable, although it may be attached to the carburetor or the throttle body on select models. This spring will close the throttle valve, which helps reduce the fuel flow to the engine and helps to slow it down. The spring can become stretched or snap over time with regular use. A faulty throttle spring could be identified by the throttle sticking or lacking any control at all. This simple repair will require needle nose pliers, sockets, a screwdriver, and a wrench. Be sure to use gloves to perform all repairs and use caution when replacing the throttle spring to prevent damage to the new part. This OEM throttle spring is designed for use with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and other small engines in lawn care equipment. It is compatible with more than 150 models and a number of brands, including Troy-Bilt, Husky, Yard-Man, MTD, Yard Machines, and Cub Cadet.

The governor rod is a genuine replacement part found on select models of snowblowers. This rod is responsible for connecting the throttle cable and throttle body, helping to open and close the throttle to change the speed of the engine. This durable metal rod is exposed to repetitive motion and constant vibrations, which can cause damage or wear over time. If this rod does not function, the throttle will be unable to be controlled and that can affect the use of the equipment. Replacing the governor rod with this genuine part will guarantee an exact fit for compatible units. This genuine governor rod is manufactured to specific OEM standards and can be used in compatible machines from Cub Cadet, MTD, Yard Man, Craftsman, Troy-Bilt, Yard Machines, and HUSKEE. The part can be found in snowblowers, with hundreds of possible models that can take this governor's rod. It is made of durable metal and sold as an individual unit. No additional components or hardware are included, and any additional parts will require a separate purchase. Always wear gloves and perform engine repairs only when the machine has had time to cool. Be sure to disengage the engine before doing any work for safety, as well.

This replacement part is a push rod kit. This is a genuine replacement part made by MTD. This part is commonly found in certain types of lawn mowers and assists the user in maneuvering the machine in the desired direction.A new push rod kit might be needed if the current one is damaged in any way. This might include being bent, dented, cracked, or chipped. If this is the case, the rod might not be able to function properly and should be replaced so that the appliance can return to working order. Be sure the engine is powered down before attempting to replace or repair this part in any way. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This is a genuine MTD fuel cap replacement made for use on select snowblowers. It features a molded gasket for secure sealing and less risk of losing parts. The fuel cap is responsible for securing the fuel in the fuel tank during operation so that it doesn't spill out. There is an air hole in the cap to prevent pressurization of the fuel, ensuring safe operation at all times. This cap is made of plastic and it can become cracked or stripped with regular use. If it is damaged, the fuel will not be secure and the machine will not be safe to use. That will require an immediate replacement. This OEM fuel cap is made to exact standards by MTD and is compatible with several models of snow blowers and snow throwers. It is also capable of fitting select models from Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. It features an easy plastic grip and a seal to prevent spillage. It can be installed with no tools and is sold as an individual unit. It is easy to screw the new cap into place, but be sure to thread the screw properly to prevent accidental stripping or misthreading that can cause the cap to get stuck.

This fuel tank assembly can be used as a replacement part for the small engine of a snowblower or a tiller. The fuel tank assembly contains the fuel tank as well as the parts required to install the part. The purpose of the fuel tank is to store fuel for the engine and dispense the fuel in order to power the engine.A fuel tank assembly might be ordered as a complete replacement part if the fuel tank and its components suffer damage. This damage might manifest in the form of fuel leakages from punctures, holes, or corrosion to the material. If this damage affects the fuel tank and its components, it should be removed and replaced before using the appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, MTD. It is sold individually. This fuel tank assembly is compatible with the following brands: MTD, Troy-Bilt, Yard Man, and Cub Cadet.

The purpose of the fuel nipple in a small engine is to clean the fuel before it reaches the carburetor. If the fuel is dirty, it could cause issues with the carburetor and other parts of the engine. If the engine misfires, has a fuel odor, leaks, or has problems with dirty fuel getting into the carburetor, it may be time to replace the fuel nipple. It is an easy replacement, but be sure to work in a well-ventilated area. Drain the fuel tank and disconnect the spark plug before beginning this repair. This OEM fuel nipple is a genuine part right from the manufacturer. This fuel nipple can work well for snowblowers, snow throwers, chippers, tillers, and log splitters. It is compatible with a range of models from brands like Craftsman, Yard Machines, Yard-Man, MTD, and Troy-Bilt.

The fuel line is used to carry fuel through the machine, and it must be in good condition. As fuel line parts age, they are prone to damage. In some cases, they might crack, which could result in a fuel leak. Other times, the ends of the tube might not fit properly, even when they are clamped down. Eventually, the fuel line will need to be replaced. This is a relatively simple job, which will require only a pair of pliers to complete. This replacement fuel line kit is sold individually. This OEM kit will include the rubber tube as well as two metal clamps for attaching the line to the machine. The fuel line may be used with snowblowers, lawnmowers, tillers, leaf blowers, log splitters, wood chippers, and other small engines, It will work with machines from many different brands, including MTD, Yard Machines, Troy-Bilt, Yard-Man, Bolens, Cub Cadet, and Husky.

A gas powered engine often requires priming before it can run, which means injecting some of the fuel into the engine's carburetor. Here, a careful balance of air and gas will receive a spark that causes combustion. The most common way to prime an engine is to use a primer assembly that is activated by a bulb that is pressed to create suction and draw fuel into a reservoir or carburetor. This replacement fuel bulb is for snowblowers that rely on gas powered engines to run. The fuel bulb is very flexible and made to endure seasonal conditions. It works with Craftsman, Yard Machines, MTD, Troy Bilt, and Bolens snowblowers. This is an OEM replacement part that fits into the cover assembly and which requires only a wrench to replace and install. It is sold individually, and other components of the priming assembly may be needed.

The flywheel key keeps the engine flywheel and the crankshaft connected. In the event that the engine is forced to a sudden stop, the flywheel key could be sheared off, making it impossible for the engine to start back up again. Replacing the flywheel key is a part of routine maintenance for many modern engines, so it should be inspected and replaced as needed. This sturdy metal flywheel key is easy to install, but remember to choose the right torque setting when doing the replacement. Always disengage the spark plug and wear gloves when replacing engine parts. This genuine flywheel key is designed to be used in a number of lawn and garden equipment products from MTD, Troy-Bilt, Yard Machines, Cub Cadet, Yard-Man, Husky, and Bolens. It can be used as a replacement for many models of snowblowers, lawnmowers, and log splitters. Sold individually.

This replacement part is an engine, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. This is a complete engine and is found in many different types of lawn mowers. The engine is arguable the most important part in and machine as it allows the entire appliance to operate. In many cases, the appliance is out of commission if the engine does not work.A new engine might be needed if the current one is not starting, or stops during use. If the user notices sounds or unfamiliar noises coming from inside the engine it might be time to replace it. There are many things that could be wrong inside the engine, be sure to check more specific parts to ensure that the entire engine needs to be replaced rather than only one smaller part. This is a genuine OEM part sourced directly from the manufacturer. This engine is sold individually.

This replacement part is a cylinder head assembly. The cylinder head assembly covers the engine head cylinder and houses the cylinder valves. Over time, the cylinder head assembly can become damaged due to excessive wear and tear. If the engine is no longer running as efficiently as it once did, the cylinder head assembly might need to be replaced. Luckily, this is a fairly simple repair.Before beginning, make sure the engine of the mower has cooled. Once cool, begin by lifting up the hood or engine cover and detach it. Remove the air filter cover. Lift out the air filter. Using a three-eighths socket or wrench remove the blower housing mounting bolts. Detach the oil drain tube and lift off the blower housing. Unthread the bolts that secure the intake manifold and detach the breather tube. Set the carburetor assembly aside. Then unthread the spark plug. Remove the mounting bracket and unthread the exhaust manifold bolts. Pull the manifold free of the muffler. Unthread the valve cover mounting bolts. Pry the cover off with a putty knife and be prepared for some oil to spill. Once the cover is off use the three-eights inch socket wrench to remove the old cylinder head mounting bolts. Pull the old cylinder assembly out of its place and replace it with the new assembly.This genuine OEM part is compatible with MTD brand lawnmowers.