Parts for Remington 41AS2BVG983: Engine Assembly Parts

This is a replacement spark plug that is designed specifically to be used with select string trimmers. the spark plug is connected to the ignition module and is responsible for creating the spark that starts the internal combustion engine. Over time, the electrode on the spark plug will wear down. Other issues can also arise that cause the spark plug to foul or stop working. Spark plugs are part of routine maintenance on any engine, but most owners keep a spare or two around just in case of emergencies. In the event that the spark plug is bad, the engine will not start. This genuine OEM spark plug is manufactured by MTD and designed for use in select trimmers. It is compatible with over 50 models of string trimmers from MTD, Bolens, Murray, Troy-Bilt, Yard Man, and Cut Cadet. Owners will need to consult their product diagram or manual to find the exact gap for the spark plug when replacing them. Many models claim to come pre-gapped, but they can settle during shipping and should always be re-gapped prior to installation. This is sold as an individual unit. Be sure to wear gloves for hand protection when replacing spark plugs and performing other maintenance.

The short block is an essential aspect of any engine. The short block includes a cylinder head, a ram shaft, and a valve-train. The short block is a portion of the cylinder block in a small engine, on the bottom end of the engine. This part connects to the crank and pistons inside the engine. This part is typically used to power smaller handheld tools such as electric or gas blowers for yard maintenance. Short blocks sometimes need to be replaced if they have a spun rod bearing and low compression. The short block must work in order for the engine to function properly. Misuse of the engine can cause failures. This replacement part is necessary for a full engine rebuild.This is a small model, 27cc Sc, specially designed to replace part number AP6085346. This short block is silver with a black valve-train. This is a genuine MTD part. This short block is compatible with various two-stroke engines. This model fits with Craftsmen, Remington, and Yard-Man models of handheld tools. This is an OEM replacement part sourced directly from the manufacturer. Sold individually.

This part is a replacement screw. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a stripped or misplaced screw in a variety of outdoor power equipment. This screw is a genuine piece of standard hardware that can have many potential uses. It's important to use screws sourced from the manufacturer to ensure a proper fit and high quality. Screws are essential for securing parts and holding the equipment together and should be replaced if worn, broken, or lost. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. When working on or near an engine, ensure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this screw, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this screw is suitable for use on several different models of blowers, edgers, and trimmers manufactured by MTD, Ryobi, Yard Man, Cub Cadet, and Troy-Bilt. This is a genuine part made of high-quality, durable metal and is sold individually.

This part is a replacement fuel tank. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a broken, cracked, or defective fuel tank in a variety of leaf blower models. The fuel tank holds the gasoline that is needed to power the leaf blower. If it is cracked, the fuel may leak, which can be costly and dangerous. The leaf blower cannot function without a fuel tank, so if damaged, this part must be replaced. It's important when working on or near to any engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this fuel tank, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this fuel tank is suitable for use on several different models of leaf blowers manufactured by MTD, Craftsman, Troy-Bilt, and other brands. Please This is a genuine part made of high-quality, durable plastic and is sold individually.

These O rings are replacement parts intended for use in a number of gasoline-powered lawn trimmers. The O rings serve as gaskets and are placed at the entry and exit points in the carburetors where gasoline and air are mixed and the expansion powers the trimmer. Though constructed of durable material, periodically the flow of the air/fuel mix or the rush of expanding air will cause damage to occur to the O rings so they become less resilient and the carburetor functions less efficiently. In these cases, users often decide to replace not just the element of the carburetor but the O rings as well. Users may notice problems with the carburetor when they cannot get an adequate adjustment, allowing the trimmer to function smoothly. They may also have trouble getting the trimmers to start at all or run without smoking. To replace the O rings, remove the air filter cover and carburetor. Once the carburetor has been cleaned, and the gasket and filter replaced, add a fresh mix of 40:1 fuel. The trimmer should start immediately. These OEM certified O rings are compatible with Bolens, Troy-Bilt, Yard Machines, and Craftsmen trimmers.

This is an insulator assembly includes the insulator, seals, and hardware. It is designed to create the right spacing between the cylinder and carburetor on many blowers and trimmers made by various manufacturers. The insulator assembly also keeps heat from moving between the other components. Over time, the insulator assembly can become damaged or crack. When this occurs, air can reach the engine and create a condition where the engine can't perform at its best. If this happens, the insulator assembly will need to be replaced. Take off the air filter, drain the fuel, and remove the intake assembly. The insulator can be taken off of the engine before the replacement is added. Use mounting screws to fit the insulator to the other components. Reassemble the other parts to use the tool.This insulator assembly is a genuine OEM replacement part sourced directly from the manufacturer. It is sold as an individual part. This component is made to be used in leaf blowers, tillers, and string trimmers manufactured by Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Bolens, and Yard-Man.

A carburetor gasket is a thin rubber material that provides a seal between two parts. Its primary purpose is to prevent fuel and air leaks. This gasket is installed between the air cleaner and the carburetor. Over time, it can crack and tear due to heat and fuel exposure. When this happens, the carburetor may produce the wrong combustible mixture for the engine. In return, the engine may experience rough idling and flooding. A carburetor gasket replacement is necessary. MTD makes this carburetor gasket replacement. It is manufactured to fit string trimmer, leaf blower and tiller made by MTD, Bolens, Troy-Bilt, and Craftsman. This brand-new carburetor gasket is sold individually. A fully assembled carburetor and O-ring are sold separately.

This part is a replacement air cleaner cover. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current air cleaner cover is defective or broken, this part can be used as a replacement. It is intended for use with a variety of trimmer and blower models.The air cleaner cover provides protection for the air cleaner itself. If it is broken in any way, it can expose the air cleaner to damage. Thus, this part should be replaced if ineffective. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this air cleaner cover, the appropriate owner's manual and equipment diagrams should be referred to. This air cleaner cover is suitable for use on a variety of trimmer and blower models manufactured by MTD, Craftsman, and other brands. It is a genuine OEM part and thus is made of high-quality, durable materials. Part sold individually.

This is a replacement air filter for a trimmer, leaf blower, or vacuum. It is necessary to prevent any significant quantities of dust or debris commonly kicked up during the use of the machine from entering into the engine. It could block the airflow, overheat the motor, and harm or destroy it. This OEM replacement part is straightforward to install and depending on the model, will usually require little more than a screwdriver to effect the repair. The removal of the housing over the filter is needed, and then it is a matter of just removing the clogged our outdated filter and slipping in the replacement. Shaped like a cup, it will fit snugly into the housing, and make reassembly just as simple. Before replacement, the filter should be treated with some oil by popping it into a plastic bag with a few drops of oil and working it into the material. This genuine OEM air filter works with Craftsman, Ryobi, Troy Bilt, Yard-Man, Bolens, MTD, Cub Cadet, and Murray machines, among others. It ships individually.