Estate Washer Screws, Nuts, Washers

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

This is a genuine replacement screw used to secure appliance components. It provides a simple, reliable fastener for reattaching panels, brackets, or assemblies so parts stay properly mounted and stable during operation. What it does

• Secures panels, trim, brackets or small assemblies in place
• Restores proper fastening where a missing or damaged screw causes loose parts or rattling
• Prevents movement that can lead to noise or misalignment of adjacent components
• Used wherever the original screw was removed or lost during repairs

• One replacement screw

• Use the matching screw head and thread engagement; do not force if it does not seat smoothly
• Tighten until snug—avoid overtightening to prevent stripping or cracking plastic parts
• Disconnect power before working on electrical appliances and follow basic safety precautions
• If original screw was rusted, check mating threads for damage before installing new fastener

This is a replacement mounting screw used to secure appliance panels and components. It restores proper fastening so panels and parts stay aligned and stable during normal use. What it does:

• Fastens appliance panels, trim or internal components in place
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop panel vibration and maintain proper component alignment
• Matches OEM fit where specified for a secure installation

• One replacement mounting screw

• Verify screw size and fit before installation; use the correct screw location from your parts diagram
• Turn off and disconnect power to the appliance before accessing internal components
• Hand-start the screw to avoid cross-threading; tighten until snug—do not over-tighten
• Wear safety glasses and follow manufacturer service instructions when applicable

This agitate gear washer is a small flat washer used with the washer's agitate gear to ensure proper spacing and smooth engagement. It helps maintain correct gear alignment so the agitator can move laundry effectively. What it does:

• Provides a stable spacer between the agitate gear and mating components to prevent excess play
• Helps maintain correct gear alignment for consistent agitator movement
• Reduces metal-on-metal contact that can cause noise or premature wear
• Commonly replaced when the agitator feels loose, makes grinding noise, or causes uneven agitation

• High-level replacement: remove agitator/gear per service manual to access washer; reinstall in original orientation
• Use manufacturer torque/settings for reassembly; do not overtighten
• Inspect adjacent gear and splines for wear; replace any damaged components
• Disconnect power and follow safety procedures before servicing the washer

This is a genuine replacement mounting screw that secures appliance components and panels so parts stay aligned and stable. Installing the correct screw restores proper fit and helps eliminate vibration or loose panels. What it does:

• Fastens panels, brackets, or small components in place
• Replaces missing, stripped, or damaged screws that cause loose parts
• Helps stop rattling, vibration, or misaligned panels
• Restores secure connections after repairs or part replacement

• One mounting screw

• Unplug the appliance or disconnect power before starting work
• Use the correct screwdriver bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep removed hardware organized so you can reuse existing screws when applicable

Size: 10 - 24 x 3/8