Estate Washer Control Board

The Control Timer is an OEM replacement part specific to Whirlpool washers. It is the electronic component responsible for governing the sequence and duration of wash cycles. Located inside the control console, the timer works with the control dial to initiate various wash/rinse phases based on the selected settings.

Causes for timer failure may include water exposure corroding electrical circuits or repeated rapid switching wearing out internal switches.

Symptoms of a faulty control timer include:

• Inability to advance through complete cycles
• Random operation of rinse or spin functions
• Premature termination of cycles before finishing
• Failure to respond when turning the cycle selector

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Timer is an OEM replacement part for Whirlpool washers. This electronic part is essential for accurately tracking washing cycles and automatically shutting off the washer at the end of the selected time period.  

Symptoms of a bad timer include:

• Cycles failing to complete fully and the washer not turning off automatically
• Inaccurate timekeeping causing under or over-washing of clothes
• The dial not rotating smoothly between settings or options  

Causes of a bad timer can include normal wear over years of use. The internal timekeeping components can degrade or fail due to repeated power cycling of the washer.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.

The Timer is an OEM part for Whirlpool washing machines. This part controls the various cycles of the washing machine, including wash, rinse, and spin cycles, by regulating the amount of time each cycle runs.

Causes of a bad timer can include electrical malfunctions, wear and tear over time, or damage to the timer's internal mechanisms.

Symptoms of a bad timer include:

• The washer not advancing through cycles
• Cycles running too long or too short
• The washer stopping mid-cycle
• Inconsistent or unpredictable cycle timing

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This mechanical cycle timer controls the sequence and duration of operations in the selected program. Replacing a worn timer restores reliable cycle selection and proper advancing from start to finish.

• Controls cycle timing and advancement via internal cams and contacts
• Directs power to components in the correct order for each cycle
• Stops the appliance at the end of the cycle
• Fixes: cycle won't advance or gets stuck, won't start, stops mid-cycle, dial doesn't move or skips

• Disconnect power before servicing
• Access the timer through the control console; remove knob/dial as needed
• Transfer wires one at a time from the old timer to the new unit, matching terminals
• Reuse existing mounting hardware and console parts; verify proper alignment before reassembly

This genuine OEM part is a timer for washers. The timer is the part that allows the washer to start and stop after being in use for a amount of time. The settings of the timer are controlled by the user and adjusts automatically depending on the desired settings. If the washer is no longer stopping after the desired time has elapsed, the timer might need to be replaced. To replace the timer, start by making sure the washer is unplugged. After that, pull the washer away from the wall to access the back panel. Once accessed, remove the screws that attach to the back panel and locate the timer. Once found, remove the mounting screws that hold it in place. Proceed to pull the timer out of the washer and replace it with the new part. This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washing machines.

This mechanical timer controls the wash-cycle sequence on top-load washers—coordinating fill, agitate, drain, and spin. Replacing a failed timer restores proper cycle advancement and reliable start/stop so each step runs at the correct time.

• Controls the timing and order of fill, wash/agitate, drain, and spin functions
• Switches power to the motor, pump, and water inlet valve at the proper moments
• Common failure symptoms: cycle won't advance or stops mid-cycle; skips agitate or spin; runs past the end of the cycle
• Knob doesn't advance or must be manually turned to proceed between steps

• Disconnect power before servicing; turn off water if you'll be moving hoses
• Access through the control console; photograph wiring and transfer connectors one at a time to matching terminals
• Mount the timer securely and align the shaft with the knob/dial—do not force the shaft
• Reassemble the console and run a test cycle to proper advancement

The Timer is an OEM part for Whirlpool washing machines. This component is responsible for controlling the various cycles of the washing machine, ensuring that each phase, from washing to rinsing to spinning, occurs at the correct time and duration.

Causes of a bad timer can include electrical faults, wear and tear on the internal mechanisms, or damage due to power surges or moisture exposure. Over time, these issues can interfere with the timer's ability to accurately manage the washing cycles, leading to performance problems.

Symptoms of a bad timer include:

• The washing machine not advancing through cycles
• Incorrect cycle durations
• The machine getting stuck in one part of the cycle
• Unresponsive or erratic timer controls

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Restore accurate cycle control with this washer timer. It sequences power to the drive motor, pump, and water inlet valves so the machine fills, washes, drains, and spins at the proper times.

• Advances the cycle through fill, wash, rinse, drain, and spin stages
• Sends power to the motor, pump, and inlet valves in the correct order and duration
• Safe symptoms: washer won't start, won't advance, stops mid-cycle, runs indefinitely, or skips rinse/spin
• Helps when cycles stall or the dial turns without moving the cycle forward

• Unplug the washer before servicing
• Open the control console to access the timer; note or photograph wiring
• Transfer wires one at a time to matching terminals on the new timer
• Reuse your existing knob/dial and mounting hardware; align the timer shaft before tightening

Please Note Mounting holes must be tapped using old screws. If the old screws are damaged beyond use order part number WP3400064

Restore dependable cycles with this replacement timer. It controls the sequence and duration of each step, sending power to the correct components at the right time so the machine advances smoothly from start to finish. What it does:

• Directs power to components to run each cycle segment in order
• Advances the cycle through preset intervals
• Helps resolve cycles that won't start or won't advance
• Addresses stopping mid-cycle or only running on certain settings
• Can help when the timer dial doesn't move or advances intermittently

• 1 timer

• Disconnect power before servicing; turn off water supply if applicable
• Access the control console; remove the knob/escutcheon if required and unmount the timer
• Transfer wires one at a time to the new timer or use a photo to match positions
• Reassemble and run a short test cycle to proper operation