Parts for Thermador PRD48JDSGU/02: Facia Panel / Knobs Parts

This display is the user interface module that shows cycle status, settings and error indicators so you can read and control the appliance from the front panel. It restores visible feedback and menu information for normal operation. What it does

• Provides the visible display for cycle progress, timers and selected options
• Shows error codes and status messages to help identify issues
• Works with the appliance control board to update settings and user inputs
• Restores readable display after a failed or cracked panel

• Disconnect power to the appliance before starting work to avoid shock or damage
• Replacement typically requires removal of the front control or console panel; handle the display lens and ribbon connectors carefully
• Keep screws and small fasteners organized for reassembly

This temperature regulator is the mechanical thermostat that controls oven heat. It senses cavity temperature and cycles the heat source on and off to reach and maintain your set temperature for consistent baking and roasting performance. What it does

• Senses oven temperature via a capillary bulb and tube
• Opens and closes internal contacts to control the heating source
• Maintains the selected temperature during cooking cycles
• Help resolve: oven not reaching set temp, overheating or wide swings, uneven baking, or unresponsive temperature control

• 1 temperature regulator

• Disconnect power; shut off gas. Allow the appliance to cool completely
• Note the original routing of the sensing bulb and capillary; reinstall the new one in the same path and clips. Do not kink, sharply bend, cut, or shorten the tube
• Transfer any knob/shaft components as needed and align properly
• After installation, verify temperature with an oven thermometer and adjust per service instructions if applicable

This push-button switch is a user-interface component that completes electrical circuits when pressed, restoring control to the affected function. It replaces a worn or failed switch to help regain reliable button response. What it does:

• Acts as the tactile electrical contact for a control or door function
• Restores responsiveness when a button no longer actuates the appliance
• Can stop intermittent operation caused by a worn or corroded switch contact
• Common symptom: controls or a specific function do not activate when the button is pressed

• One push-button switch as shown

• Disconnect power to the appliance before beginning any work
• Access may require removing a console or panel—keep track of fasteners and wire locations
• Disconnect wiring harness or terminals carefully; note connector orientation for reassembly
• Test the new switch with the power off using a multimeter continuity check before reassembly

This replacement panel fascia is made by Bosch and is compatible with ovens. This panel fascia fits onto the outer portion of the oven control and display panel. It is primarily intended to keep the display and controls safe and protected, to prevent significant wear and tear, and for aesthetic purposes. The panel fascia might become worn, cracked, dented, bent, detached, or otherwise broken over time, requiring replacement. This part can be replaced using basic household tools. It's recommended that the appliance is disconnected from the power source before beginning.This is an authentic OEM part made of high-quality, durable materials and is sold individually. This panel fascia can be used with compatible models of ranges manufactured Bosch, Thermador, Gaggenau, and other brands.

The Knob is an OEM part for Bosch ranges. This knob allows users to control the temperature and cooking settings on their stove or oven effectively.  

Causes of a bad knob can include prolonged exposure to heat, which can cause the material to degrade, accidental damage, or normal wear and tear that leads to cracking or breaking. 

Symptoms of a bad knob include:

• Difficulty in turning or adjusting the knob
• The knob feeling loose or falling off
• Visual signs of damage such as cracks or melting
• Failure to engage the stove or oven controls properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This is a replacement cooking area knob that restores user control of a cooktop's heat/zone selector. It matches the original shape and detent pattern for a secure fit and reliable operation. What it does:

• Replaces a cracked, worn or missing cooking area control knob
• Restores tactile control for burner/zone selection and temperature settings
• Helps stop slipping or inaccurate pointer alignment during use
• Fits on the original shaft to maintain safe operation

• Remove power to the appliance or turn element to OFF before servicing
• Pull off the old knob straight from the control shaft; press the replacement onto the shaft until seated
• If knob does not seat easily, confirm correct orientation and shaft type before forcing
• If controls still don't work after installation, check the switch or control assembly (replacement knob only replaces the user interface)