Parts for Bosch HDI8054U/04: Frame Parts

Replaces cracked or damaged rear housing cover on your range. Protects internal components and ensures proper ventilation through integrated vents.

This Terminal Box is an OEM part for Bosch Built-In Ovens. Integral to the oven's electrical system, this component serves as a secure connection point for various electrical wires within the appliance.

A common issue with a malfunctioning Terminal Box is loose connections or damage to the terminal block due to heat exposure or aging. 

Symptoms of a defective Terminal Box may include:

• Inconsistent power supply to the oven
• Non-functional heating elements
• Sparks or electrical arcing within the terminal box area

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Range not responding to controls or cycles not running properly? This programmed control module serves as the main electronic board, restoring function.

Fix misaligned oven components with this spacer. Restores proper gap between parts to prevent rubbing and ensure smooth operation. Simple DIY repair.

This replacement routing tube channels fluid inside the appliance to restore proper flow and stop leaks. It replaces a damaged, cracked, or clogged tube to help prevent water pooling and restore normal operation. What it does:

• Routes water or condensate between internal components to maintain proper drainage or flow
• Replaces cracked, split, or deteriorated tubing that can cause leaks or puddles
• Helps eliminate intermittent dripping or loss of water flow caused by blockages or holes
• Works as a direct-fit replacement when the original tubing has failed

• One replacement tube

• Disconnect power and shut off the water supply before installing
• Inspect and reuse or replace any retaining clips, clamps, or grommets as needed
• Slide tube fully into fittings and secure with appropriate clamps to prevent leaks

Replace your range's side panel if it's cracked, dented, or showing rust. This exterior panel covers the side of your appliance for a complete look.

Leveling foot for electric and gas ranges. Adjustable metal foot installs at base corner. Replace if cracked, broken, or missing to level your range.

Fixes inconsistent flames or weak heating on your range. This gas pressure regulator stabilizes fuel flow to burners for reliable cooking performance.

Replace the side panel on your range. This exterior panel covers the side of the appliance. Order a new one if yours is dented, scratched, or damaged.

This cable harness routes electrical signals between dishwasher components to restore proper control and power delivery. It replaces a damaged or broken wiring assembly so affected circuits can communicate and operate reliably. What it does:

• Connects control board, sensors, pumps and other internal components to carry power and signals
• Restores intermittent or lost power to specific assemblies caused by frayed or broken wires
• Helps eliminate error codes or failures tied to open or shorted harness connections
• Prevents arcing and poor connections that can cause unreliable operation

• One cable harness assembly as pictured

• Only install after disconnecting power to the appliance to avoid shock or damage
• Inspect mating connectors and pins for corrosion or damage before connecting
• Route harness away from sharp edges, moving parts and hot surfaces to avoid future wear

Fix intermittent power or electrical faults in your range with this cable harness. Routes power and signals between control and components. Direct fit.

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

The Screw is an OEM part for Bosch gas cooktops and ranges. It anchors the surface burner head assembly onto the cooktop surface.

Causes can be stripped threads or overall wear from repeated heating/cooling cycles. Exposure to cooking spills or impacts may also deteriorate the screw head over time.

Symptoms of a bad burner head screw include:

• A burner detaching from the cooktop surface entirely
• Excess movement or instability of burner heads when in use
• Gas leaks reported around the burner head connection points

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.