Parts for Bosch B22CS30SNS/01: Freezer Door Parts

The Water Filter is an OEM part for Bosch refrigerators. This part removes impurities and contaminants from the water supply to your appliance. This part ensures that the water and ice dispensed by your refrigerator are clean, taste fresh, and are free of common waterborne particles and substances. 

Over time, the water filter can become clogged with sediments and contaminants, reducing its effectiveness and potentially affecting the taste and quality of the water and ice. Regular replacement is essential for maintaining optimal performance.

Symptoms of a bad Water Filter include:

• Unpleasant taste or odor in the water or ice
• Decreased water flow to the dispenser or ice maker
• Visible particulate matter in the water or ice cubes

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This is the replacement outer door panel for select Bosch appliances, providing a finished exterior surface and restoring the door's appearance and function. Replaces a damaged, dented, or cosmetically worn door panel to help secure the appliance front. What it does:

• Restores the appliance's exterior face and sealing fit where the outer door panel is damaged or bent
• Helps maintain proper alignment of door trim and controls mounted to the front
• Reduces drafts and helps the appliance door close properly when the outer panel was interfering
• Improves appearance by replacing scratched, dented, or rusted surface finishes

• One outer door panel

• Installation may require removing interior trim, hinges, and attached components
• Keep power disconnected and water supply off before beginning repairs
• Handle sharp edges and heavy panels carefully; use gloves and a second person for safe positioning
• If the door contains electronics, wiring, or trim pieces, verify which subcomponents transfer or require replacement per the OEM instructions

This replacement door seal fits into the groove around the dishwasher opening. It compresses against the door to create a watertight barrier, helping stop front leaks and restore a proper, snug close. What it does:

• Forms a continuous seal to keep wash water inside during all cycles
• Helps the door latch compress correctly for a tight, secure close
• Replaces cracked, flattened, or torn gasket that can drip at corners or along the bottom
• Helps resolve: water on the floor at the front, moisture or steam escaping, door harder to close

• Includes 1 door seal

• Disconnect power and shut off the water supply before servicing
• Pull the old seal straight out of the channel; clean the groove of debris and residue
• Start at the top center; press the new seal evenly into the channel without stretching, ensuring corners are fully seated
• Close and reopen the door to seat the seal; run a short cycle and check for leaks

This replacement door seal fits into the groove around the dishwasher opening. It compresses against the door to create a watertight barrier, helping stop front leaks and restore a proper, snug close. What it does:

• Forms a continuous seal to keep wash water inside during all cycles
• Helps the door latch compress correctly for a tight, secure close
• Replaces cracked, flattened, or torn gasket that can drip at corners or along the bottom
• Helps resolve: water on the floor at the front, moisture or steam escaping, door harder to close

• Includes 1 door seal

• Disconnect power and shut off the water supply before servicing
• Pull the old seal straight out of the channel; clean the groove of debris and residue
• Start at the top center; press the new seal evenly into the channel without stretching, ensuring corners are fully seated
• Close and reopen the door to seat the seal; run a short cycle and check for leaks

This cover is a replacement access panel that protects internal components and helps keep wiring and mechanisms secure. It restores a finished appearance and shields parts from moisture and debris. What it does:

• Covers and protects internal components behind the appliance control or service area
• Helps prevent accidental contact with wiring and moving parts
• Keeps dust, lint, and moisture away from sensitive components
• Restores the original fit-and-finish of the appliance exterior

• Disconnect power before attempting any repair to avoid electric shock.
• Remove only the fasteners specified by the manufacturer and keep track of hardware.
• Replace any damaged clips or screws.

A replacement hinge pivot bearing that supports the dishwasher door for smoother, quieter opening and proper alignment. Fits into the door hinge assembly to reduce binding and wear for reliable door operation. What it does

• Supports the door hinge pivot so the door opens and closes smoothly.
• Reduces friction and wear on the hinge, helping prevent sagging or misalignment.
• Stops squeaks, sticking, or rough movement caused by a worn bearing.
• Works as a direct replacement for the corresponding hinge bearing in the door assembly.

• Disconnect power to the appliance and shut off water before starting any repair.
• Support the door while removing hinge fasteners to prevent the door from dropping.
• Access typically requires removing the lower toe panel or inner door trim—use basic hand tools.
• Inspect hinge components and nearby parts for wear; replace any damaged hardware and test door alignment after installation.

The Motor is an OEM part for Bosch refrigerators. This motor is specifically designed to power the ice dispenser mechanism, allowing for the convenient dispensing of ice cubes or crushed ice. It delivers the necessary power to rotate the dispenser auger, providing you with a steady supply of ice whenever you need it.

A bad motor can occur due to wear and tear, electrical malfunctions, or motor failure. Signs of a faulty motor include the ice dispenser not working, the auger not rotating, or unusual grinding or buzzing noises during ice dispensing.

Symptoms of a bad motor include:

• Inability to dispense ice  
• Noisy or erratic operation 

Replace your malfunctioning or worn-out ice dispenser motor with this genuine OEM Bosch part to restore your refrigerator's ice dispenser. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This support is a replacement mounting bracket that secures internal components and keeps assemblies aligned for reliable operation. It restores proper component support to reduce movement and abnormal noise. What it does:

• Holds and stabilizes an internal assembly or panel to prevent sagging or misalignment
• Helps eliminate rattling or knocking caused by loose or broken supports
• Restores correct alignment for connected parts to ensure smooth operation
• Prevents further wear by keeping components properly positioned during use

• Designed to replace a worn or damaged support; inspect adjacent hardware for wear before installing
• Remove power and follow manufacturer's safety procedures before servicing
• Installation may require basic hand tools; handle plastic parts carefully to avoid cracking
• Reassemble panels and test function after installation

This replacement lid restores the appliance's finished top cover, protecting internal components and helping the door/hatch close properly. Use when the original lid is cracked, warped, or missing to keep the unit looking and operating as intended. What it does:

• Covers and protects the appliance's top/opening area from debris and damage.
• Secures to existing hinge or mounting points to ensure proper closure.
• Replace if you see visible cracks, chips, warping, or if the lid no longer latches or aligns.
• Helps prevent rattling or rubbing caused by a damaged or loose lid.

• Disconnect power (and water, if applicable) before starting any repair.
• Handle edges carefully; some lids include glass or thin sheet material that can chip.
• Basic hand tools (screwdriver/torx) may be required; keep mounting hardware if reusing.

This replacement tube routes fluids between internal components to restore normal flow and prevent leaks. It fits specific Bosch appliances and replaces a worn, cracked, or damaged original tube. What it does:

• Channels water or drain flow between appliance components to maintain proper operation
• Stops leaks caused by cracked, split, or hardened tubing
• Helps restore normal water flow that can cause poor washing or filling performance
• Prevents intermittent operation caused by restricted or collapsed tubing

• Disconnect power and shut off the water supply before starting any repair
• Inspect and replace any damaged clamps, grommets, or seals when installing the tube
• Ensure the tube is routed without kinks and secured with the correct clips or clamps
• Test the appliance for leaks and proper operation after installation