Parts for Ge GTY22IBBJRSS: 01 - Freezer Door Parts

This large door handle assembly replaces a worn, cracked, or broken refrigerator door handle to restore a secure grip and original appearance. It fits the factory mount points for a direct, like-for-like replacement. What it does:

• Provides a sturdy, finished handle for opening and closing the refrigerator door
• Replaces cracked, loose, or cosmetically damaged handles
• Restores original fit and alignment at the door mounting points
• Helps prevent accidental slips or difficulty opening the door caused by broken hardware

• Disconnect power to the appliance before starting work to avoid electrical hazard
• Use basic hand tools; support the door and handle during removal and installation to prevent damage
• Keep mounting screws and trim pieces organized for reassembly; do not overtighten fasteners
• If the handle has a finish or painted surface, handle carefully to avoid scratches

This freezer door gasket forms an airtight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn or damaged seal helps restore proper temperature, reduce frost, and improve energy efficiency.

• Seals the freezer door perimeter to maintain set temperature and airflow
• Helps reduce frost/ice buildup and condensation around the door opening
• May help if you notice warm spots, frequent frost, the door not staying shut, or visible gasket tears/gaps
• Reduces warm air infiltration that can cause long run times and temperature swings

• Unplug the refrigerator before servicing
• Warm the new gasket in hot tap water or with a hair dryer on low to make it pliable; seat the corners first
• Depending on the model, either press the gasket into the retainer channel or loosen and retighten inner-liner screws to secure—do not overtighten
• After installation, check the seal all around (dollar-bill test); gently warm and reshape any areas with gaps

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

This replacement screw fastens refrigerator components securely, restoring a tight, rattle-free fit when original hardware is missing, stripped, or corroded. Use it to secure panels, brackets, or trim and keep parts properly aligned.

• Secures panels, brackets, covers, or trim in place
• Helps maintain correct alignment of components and hardware
• Reduces vibration and rattling caused by loose or missing screws
• Replaces lost, rusted, or stripped screws

• Unplug the refrigerator and turn off water supply if working near water components
• Match thread and length to the removed fastener; hand-start threads to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin sheet metal
• Keep track of any spacers or washers reused from the original assembly

This plug cover is a small protective cap that shields an appliance's power or wiring plug/terminal area from dust and accidental contact. It helps keep connections clean and reduces the risk of debris buildup. What it does

• Covers and protects an exposed appliance plug or terminal connection
• Helps prevent dust, dirt and small debris from entering the plug area
• Reduces risk of accidental contact with terminals while appliance is serviced or idle
• Commonly used when a cord or plug is not in use or during maintenance

• No special tools required; push the cover firmly into place over the plug or terminal
• Ensure the appliance is powered off and unplugged before servicing nearby components
• Inspect the cover for damage and replace if cracked or deformed
• Not intended to alter electrical connections or provide waterproofing; use only as a protective cap