Parts for Ge GTY22IBBJRSS: 03 - Freezer Section Parts

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

Evaporator cover assembly for your refrigerator. Installs over the evaporator coils in the freezer section. Replace if cracked, damaged, or missing.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Self-adhesive foam strip that installs around the refrigerator door perimeter. Replace if the original strip is damaged, cracked, or missing to restore seal.

Self-adhesive foam insulation strip for refrigerator doors. Replaces worn, compressed, or missing foam that affects door seal and energy efficiency.

Replace your refrigerator's ice bin tray when cracked, broken, or missing. This tray sits in the freezer compartment to collect and store ice cubes.

Foam insulation block that surrounds the evaporator coils in your refrigerator. Replace if cracked, deteriorated, or missing to restore proper insulation.

Evaporator housing block for refrigerators. Secures and protects the evaporator assembly. Replace if cracked, broken, or missing to restore coverage.

Replace your refrigerator's freezer light lens cover when cracked, yellowed, or missing. Protects the bulb and ensures proper lighting. Verify fit.

Replacement plug cover and gasket assembly for refrigerator electrical access areas. Restores secure fit when original is cracked, broken, or missing.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Mounting bracket that secures the evaporator fan in place inside your refrigerator. Replace if cracked, bent, or broken to properly support the fan.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Fix a warm fridge or freezer not cooling properly. This evaporator fan motor circulates cold air throughout your refrigerator. DIY repair in 30-40 minutes.

Freezer fan loud or not spinning? This evaporator fan blade circulates cold air over the coils. DIY-friendly repair with our video guide.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration o

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

This replacement defrost heater warms the freezer's evaporator area during the automatic defrost cycle. It melts accumulated frost so air can circulate, helping maintain stable temperatures and preventing ice buildup on the back wall.

• Heats the

The Defrost Thermostat is an OEM replacement part designed for use in GE refrigerators. This component acts as a safety device in the refrigerator's defrost system, preventing the freezer from overheating during the defrost cycle. It works by monit

This holder element assembly secures the appliance's heating element in the correct position so the element stays stable for consistent operation and safe performance. It's a direct-fit replacement for worn or damaged holders. What it does:

• Secu

Routes defrost water from the evaporator to the drain system. Replace this trough if cracked, clogged, or damaged to prevent water pooling inside your fridge.

Secures evaporator thermistor to tubing for accurate temperature readings. Replace if broken or missing to restore proper cooling and defrost cycles. Confirm fit.

Protective cover cap for refrigerator temperature sensor. Snaps into place to shield sensor from damage. Replace if cracked, broken, or missing.

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the

8-18 CA HX 1/2 S

Self-adhesive foam strip seal for refrigerators. Fills gaps between panels or trim to block drafts and moisture. Replace when worn, compressed, or missing.

Adhesive foam insulation strip for refrigerators. Seals gaps around doors, cabinets, or interior panels. Replace when worn, compressed, or missing.

Self-adhesive foam strip seals gaps around refrigerator doors to prevent air leaks and improve energy efficiency. Replace when worn or compressed.

Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.