Parts for Whirlpool EB9SHKXVQ04: 05 - Freezer Door Parts

The Freezer Door Handle is an OEM part for Whirlpool refrigerators. It provides a sturdy grip for opening and closing the freezer door, ensuring easy access to the freezer compartment. 

Causes of a bad freezer door handle can include normal wear and tear, repeated use, or accidental damage. 

Symptoms of a bad freezer door handle include:

• The handle feeling loose or wobbly
• Cracks or visible damage to the handle
• Difficulty in opening or closing the freezer door
• The handle detaching from the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This door gasket runs around the perimeter of the door opening to create a dependable seal when closed. A proper seal helps limit air and moisture leaks, supporting stable internal conditions, reduced condensation, and efficient performance. What it does:

• Seals the door perimeter to block unwanted air and moisture infiltration
• Helps minimize condensation around the door and maintain consistent internal conditions
• Replaces gaskets that are torn, cracked, warped, or permanently compressed
• Can help when the door won't seal properly or you notice drafts, moisture, or temperature swings

• 1 door gasket

• Disconnect power if removing the door or working near electrical components
• Warm the gasket (soak in warm water or use low heat) to relax it before installation
• Press the gasket fully into the channel/retainer, ensuring corners are completely seated
• Check for uniform contact all around; adjust door alignment if needed and allow up to 24 hours for the gasket to conform

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

This white door stop limits how far the door swings open, helping protect hinges and nearby surfaces. Replace a worn or missing stop to restore the intended opening range and smooth, controlled door movement.

• Limits door swing to prevent overextension and impact
• Helps protect door hinges and surrounding cabinetry
• Restores proper opening range when the original stop is cracked or missing
• Common signs: door opens too wide, door hits adjacent surfaces, visible broken/missing stop

• Disconnect power and clear items from the door before service
• Support the door to prevent strain on the hinges
• Remove hinge cover and fasteners as needed, swap the stop, and reassemble
• Open and close the door to verify proper swing and gasket seal

This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.

• Fastens covers, trims, brackets, and internal parts to the cabinet/frame
• Used wherever a #8-18 x 5/8 screw is specified
• Replace if the original is missing, corroded, stripped, or will not tighten
• Symptoms: loose or rattling panels, gaps, or hardware that backs out

• Disconnect power; shut off gas/water before servicing
• Match thread and length; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly—do not overtighten
• Inspect and replace damaged clips or tabs before securing

This freezer door retainer is a small mounting clip that secures the freezer door/inner panel and helps keep the door aligned for a proper seal. Replaces a broken or worn retainer to restore reliable door positioning and reduce air leaks. What it does:

• Secures the freezer door or inner door panel to the cabinet or hinge assembly
• Helps maintain proper door alignment for an effective freezer seal
• Common fix when the door drops, pulls away, or creates a visible gap
• Prevents unnecessary cold air loss from a misaligned or loose door

• One freezer door retainer

• Disconnect power before beginning repairs and follow manufacturer safety instructions
• Access may require removing the freezer door or inner panel and existing fasteners
• Inspect surrounding hinge and mounting hardware for wear and replace if needed