Parts for Bosch B18IF800SP/08: Freezer Parts

The Water Filter is an OEM part for Bosch refrigerators. This part removes impurities and contaminants from the water supply to your appliance. This part ensures that the water and ice dispensed by your refrigerator are clean, taste fresh, and are free of common waterborne particles and substances. 

Over time, the water filter can become clogged with sediments and contaminants, reducing its effectiveness and potentially affecting the taste and quality of the water and ice. Regular replacement is essential for maintaining optimal performance.

Symptoms of a bad Water Filter include:

• Unpleasant taste or odor in the water or ice
• Decreased water flow to the dispenser or ice maker
• Visible particulate matter in the water or ice cubes

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This defrost heater melts frost buildup on the evaporator to help restore normal airflow and cooling performance. It's a direct-replacement-style heater used in frost-free refrigerators to prevent ice buildup. What it does:

• Warms the evaporator coil during the defrost cycle to remove frost and ice.
• Helps maintain proper cold-air circulation by preventing ice obstruction.
• Can resolve symptoms like excessive frost on the evaporator, reduced cooling, or frequent run cycles associated with frost buildup.
• Works with the refrigerator's defrost thermostat/timer/control to perform periodic defrosts.

• One defrost heater (single heater element as shown)

• High-level replacement: disconnect power before servicing, drain/defrost appliance if necessary, and follow OEM disassembly steps for access to the evaporator compartment.
• Verify heater routing and mounting are correct and that the defrost thermostat/thermistor and control are functioning before final reassembly.

This operating module is the appliance's electronic control board that processes user commands and manages key functions. Replacing a failed module can restore proper response from the controls and consistent, reliable operation.

• Interprets control inputs and sends commands to run selected settings
• Manages power distribution and timing for electronic components
• Interfaces with sensors and display to monitor status and operation
• Failure symptoms can include unresponsive controls, blank display, won't start, intermittent operation, or control-related error codes

• Disconnect power at the breaker before servicing and verify no voltage is present
• Use ESD precautions; handle the board by its edges and avoid touching components
• Photograph connector locations and move plugs one at a time to the new module
• Some models require configuration or a reset procedure per the service manual after installation

Replacement heating element that warms dishwasher wash water and aids drying so your dishes come out cleaner and drier. Designed to replace a failed or damaged tub heater and restore proper wash temperatures and drying performance. What it does:

• Heats incoming wash water so detergents work effectively and soils are removed.
• Helps evaporate remaining water during the drain/dry cycle to improve drying results.
• Commonly needed when dishes are still cold, not cleaning well, or the dryer cycle leaves water spots.
• Restores proper temperature control when the original element is burned out, visibly damaged, or open.

• Disconnect power to the appliance before attempting any repairs to avoid shock.
• Inspect wiring and mounting hardware for damage; replace any corroded connectors.
• Basic mechanical skills recommended.
• Do not operate the appliance with exposed terminals or damaged insulation.

A direct-replacement fan motor that circulates air inside the appliance to restore proper airflow and cooling. Replacing a failing blower motor can help resolve poor temperature control and excess noise. What it does:

• Spins the internal blower to move air across evaporator/condenser coils for even cooling
• Helps maintain proper temperature and prevents hotspots or frost buildup
• Stops or corrects noisy, grinding, or vibrating operation when replacing a worn motor
• Supports normal compressor and defrost cycling by restoring designed airflow

• Disconnect power to the appliance before starting any repair
• Remove panels or shrouds as needed to access the blower assembly; keep screws and fasteners organized
• Transfer any mounting brackets, grommets, or connectors from the old motor
• Test operation after installation and verify proper airflow and quiet operation

The FIXTURE is an OEM component specifically designed for Bosch refrigerators. Typically located inside the fresh food compartment, fixtures hold slidable wire shelves, bins, crispers, and other removable storage accessories in precise positions.

Causes of a faulty fixture can include cracking or breaking of plastic rails from repeated impact or overloading. Clips and mounting attachments may also loosen over time.

Symptoms of a bad fixture include: 

• Shelves, bins, and pans that no longer slide smoothly or feel insecure
• Storage accessories like crispers that tilt or are difficult to remove
• Interior rattles or banging noises coming from loose components

This replacement Bosch fixture returns stability and structure to the organization system. Realigning fixtures maintains consistent placement and secure engagement of accessories for tidy, accessible food storage. 

Compatible with Thermador, Gaggenau, or Kenmore French door models utilizing consistent interiors.

This is an electrical on/off switch used to control power to an appliance circuit. It replaces a failed switch so controls respond normally and the appliance can be powered on and off safely. What it does

• Opens and closes an electrical circuit to enable or disable appliance power or a specific control function
• Commonly replaces a worn, stuck, or unresponsive switch that prevents controls or lights from operating
• Can resolve symptoms like no power to a control, intermittent operation, or a button that won't actuate
• Designed to mate with the appliance's existing wiring and mounting points

• One electrical on/off switch

• Disconnect power to the appliance at the breaker or unplug before working on wiring
• Verify proper wire locations and secure all terminal connections; replace only with the exact part specified by the manufacturer
• Handle the part carefully to avoid bending terminals or damaging the switch actuator

A small foam insulation/bumper used to cushion and protect appliance components, reduce vibration and noise, and help prevent metal-on-metal contact. Useful when worn or missing foam causes rattling or contact damage. What it does:

• Cushions internal components to prevent rubbing and wear
• Dampens vibration and reduces operational noise
• Helps maintain small gaps for insulation and prevents direct metal contact
• Keeps parts aligned and minimizes rattling during operation

• Disconnect power to the appliance before accessing internal components.
• Install in the correct location and orientation; replace any damaged adhesive pads as needed.
• Press firmly to seat the foam; avoid compressing excessively.

This foam piece is a small insulation/cushion component used on select Bosch appliances to reduce vibration, fill gaps, and dampen noise for quieter operation and better fit. It replaces worn or missing foam that can allow movement or rattle. What it does:

• Provides cushioning between panels and components to reduce rattling and vibration
• Acts as a gap filler to help maintain proper panel alignment and prevent rubbing
• Helps dampen operational noise from motors or moving parts
• Can restore the original fit where foam has compressed, torn, or fallen away

• Foam piece

• Disconnect power to the appliance before servicing and work with the unit in a stable, cool state
• Remove any access panels needed to reach the foam location; note panel fastener locations for reassembly
• Press the foam into the designated slot or adhesive area; replace adhesive backing or use recommended adhesive only if original method is verified

This is a replacement micro switch used in select Bosch-built appliances. It opens and closes an electrical circuit when actuated by a lever or cam, enabling functions like starting/stopping a cycle or detecting a position.

• Controls power or signals by opening/closing a low-voltage circuit when pressed
• Commonly used for on/off, door/lid, or position-sensing functions
• Failure may cause the unit not to start, intermittent operation, or features that won't engage
• May also present as unresponsive buttons or functions that only work when pressed a certain way

• Disconnect power before servicing; verify no voltage is present
• Access location varies by model; remove panels as needed to reach the switch
• Note wire positions and terminal orientation before removal
• Test continuity with a meter after installation to ensure proper operation

This cover is a simple replacement housing piece that protects internal components and restores a finished appearance to the appliance. It helps keep wiring and mechanisms enclosed while preventing debris intrusion and cosmetic damage. What it does:

• Shields internal parts from dust, splashes, and accidental contact
• Restores the appliance's finished appearance when the original cover is cracked or missing
• Helps maintain proper airflow paths and component alignment where applicable
• Reduces risk of debris-related faults by keeping openings closed

• Cover

• Disconnect power to the appliance before attempting any service
• Remove any adjacent panels or fasteners to access and replace the cover
• Handle plastic covers carefully to avoid cracking; tighten fasteners just until snug
• Note wiring or clips present behind the cover before removal

This sensor monitors operating conditions inside the appliance and reports to the control so cycles run correctly and safely. When the sensor fails, the control may receive inaccurate feedback, leading to irregular performance. What it does:

• Detects key conditions inside the appliance and sends a signal to the control
• Helps the control regulate heat and cycle progress
• Failure symptoms can include erratic cycle times, poor heating performance, or sensor-related error messages
• Can prevent the appliance from starting or completing a cycle if readings are out of range

• 1 sensor

• Disconnect power before servicing; shut off water supply if applicable
• Access the sensor and note wire orientation before removal
• Ensure any sealing surface is clean and the sensor is seated properly; check for leaks after reassembly where applicable
• Run a diagnostic or test cycle after installation to clear errors and verify operation

This NTC temperature sensor is a direct-replacement temperature probe that helps the appliance monitor and regulate internal temperatures for proper operation and consistent performance. What it does

• Measures internal temperature and sends a variable resistance signal to the control board
• Allows the appliance to detect and maintain correct temperature ranges during cycles
• A failing sensor can cause incorrect temperature readings, error codes, or improper cycle behavior
• Works as part of the appliance's temperature control and safety monitoring system

• One NTC temperature sensor

• Disconnect power to the appliance before servicing to avoid electric shock
• Handle the probe and wiring gently to avoid damaging the sensor or connector
• Verify sensor operation and wiring continuity per the appliance service manual before replacement

This water inlet valve controls water flow into the appliance, restoring proper fill and preventing unwanted leaks. Replacing a faulty inlet valve returns normal water supply and helps the appliance fill reliably. What it does:

• Opens and closes the water supply to the appliance when a cycle calls for water
• Stops water flow when the fill is complete to prevent overfilling
• Common symptom: appliance won't fill or fills slowly
• Common symptom: continuous or intermittent leaking near the inlet area
• Works with the appliance's control signals to regulate fill volume

• Disconnect power and shut off the water supply before starting any repair
• Drain residual water from hoses and fittings to avoid spills
• Inspect and replace any worn inlet hoses or seals when replacing the valve

The Installation Set is an OEM part for Bosch refrigerators. It includes the necessary parts for installing or replacing the evaporator assembly in your refrigerator.

A bad installation set can occur due to wear and tear, refrigerant leaks, or damage from external factors. Signs of a faulty assembly include inadequate cooling, frost buildup, or strange noises coming from the refrigerator.

Symptoms of a bad installation set include:

• Inadequate cooling 
• Excessive frost or ice buildup on the evaporator coil
• Unusual noises coming from the refrigerator

Replace your damaged or malfunctioning installation set with this genuine OEM Bosch part to restore your refrigerator. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

This single-use dishwasher cleaner removes limescale, grease and odor-causing residue from the interior and spray arms to help restore cleaning performance. It's designed for routine maintenance between deep-clean services. What it does:

• Dissolves limescale, hard-water buildup and mineral deposits that can reduce spray-arm flow and detergent action
• Breaks down grease and food film that cause lingering odors or cloudy glassware
• Helps clear residue from seals, filter housing and spray nozzles for more consistent wash results
• Safe for use in dishwasher tubs and internal components when used as directed

• One single-use bottle of dishwasher cleaning solution

• Follow the dishwasher maker's directions: typically empty dishwasher, place bottle in the rack or dispenser, run the specified cleaning cycle
• Use only as directed; do not mix with other chemicals or detergents
• Keep out of reach of children and pets; avoid contact with skin and eyes — rinse thoroughly if contacted
• Dispose of container per local regulations after use