Parts for Bosch B18IF800SP/08: Mounting 1 Parts

The Water Filter is an OEM part for Bosch refrigerators. This part removes impurities and contaminants from the water supply to your appliance. This part ensures that the water and ice dispensed by your refrigerator are clean, taste fresh, and are free of common waterborne particles and substances. 

Over time, the water filter can become clogged with sediments and contaminants, reducing its effectiveness and potentially affecting the taste and quality of the water and ice. Regular replacement is essential for maintaining optimal performance.

Symptoms of a bad Water Filter include:

• Unpleasant taste or odor in the water or ice
• Decreased water flow to the dispenser or ice maker
• Visible particulate matter in the water or ice cubes

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This genuine replacement strip restores the proper fit, finish, and protection at its mounting location on the appliance. It replaces a worn or missing strip to help maintain alignment and appearance.

• Provides a finished edge or cover where specified by the design
• Helps reduce rubbing, vibration, or rattling between adjoining parts
• Typical symptoms: missing/broken strip, visible gap, loose fit, rattling, cosmetic wear

• Disconnect power; turn off water or gas if applicable
• Compare to the original and note orientation before removal
• Install evenly without bending, stretching, or kinking the strip
• Reinstall adjacent panels/fasteners and verify alignment and clearances

This profile stripe is a decorative trim piece that restores the finished look of a PROFILE-series appliance door and helps protect the exposed edge from wear. It matches the appliance profile to keep the door looking complete and aligned. What it does:

• Covers the exposed door edge or seam to restore original appearance
• Protects the door edge from chips, scuffs and daily wear
• Hides mounting holes and fasteners for a clean, finished look
• Helps maintain the aesthetic alignment between door panels and handle area

• High-level replacement — typically snaps or slides into place; check for exact steps
• Use care to avoid scratching adjacent surfaces during installation
• Disconnect power or follow manufacturer safety guidance if working near electrical components
• If adhesive is used, allow recommended cure time before closing or using the door

This auxiliary tool is a small service accessory used to assist during appliance maintenance and installation. It helps make adjustments and handling of specific components easier and safer. What it does:

• Provides a dedicated hand tool used for component adjustment, alignment, or temporary support during service
• Helps reduce the risk of damaging delicate parts when installing or removing related components
• Useful for routine maintenance tasks and field service work where OEM-specified aids are required
• Can improve access or leverage in tight areas compared with bare hands

• Disconnect power to the appliance before performing any service.
• Use the tool only as described in the appliance service instructions.
• Wear appropriate safety gear (gloves, eye protection) when servicing appliances.
• Keep the tool and small parts away from children.

This cover protects and conceals internal components, keeping them free from dirt and moisture while maintaining the appliance's finished appearance. It's a straightforward replacement that restores proper fit and protection at the service area. What it does:

• Shields internal parts from debris and moisture to reduce wear and fouling
• Helps keep switches, latches, or connection points covered and secure
• Restores the appliance's finished appearance where the original cover was damaged or lost
• Supports proper component alignment by holding surrounding pieces in place

• Disconnect power and, if applicable, water supply before beginning service
• Remove fasteners or clips securing the old cover; retain screws for reuse
• Align the replacement and snap or fasten into place without forcing to avoid breaking tabs

This is a single mounting screw used to secure appliance components and panels. It replaces a missing or worn fastener so parts stay properly attached and reduces rattles or loose fittings. What it does:

• Secures panels, brackets, or small components in place
• Prevents vibration-related noise from loose parts
• Replaces stripped or missing fasteners that cause misalignment
• Restores proper fastening where original screw is lost or damaged

• One screw

• Disconnect power and water before servicing appliances
• Use the correct screwdriver or driver bit to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten until snug — do not overtighten
• Keep small parts away from children and clean up any dropped hardware

Replacement retaining pin that secures appliance components so panels, hinges or linkages stay connected. Use this direct-fit hardware to restore proper alignment and reduce looseness, rattling or separation caused by a missing, bent or worn pin.

• Secures mating parts like hinges, levers or shafts to prevent separation and play
• Common symptom: loose or rattling door/panel or misaligned assembly where the original pin is missing or damaged
• Typical use: keeps pivot points and small assemblies aligned for proper operation
• Metal fastener designed for a simple, local replacement

• Disconnect power (and water, if appliance type requires) before servicing
• Remove any obstructions and note original orientation before removing the old pin
• Use appropriate hand tools; do not force parts—if fit is tight, inspect mating components for damage