Parts for Bosch B18IF800SP/08: Compressor Parts

The Water Filter is an OEM part for Bosch refrigerators. This part removes impurities and contaminants from the water supply to your appliance. This part ensures that the water and ice dispensed by your refrigerator are clean, taste fresh, and are free of common waterborne particles and substances. 

Over time, the water filter can become clogged with sediments and contaminants, reducing its effectiveness and potentially affecting the taste and quality of the water and ice. Regular replacement is essential for maintaining optimal performance.

Symptoms of a bad Water Filter include:

• Unpleasant taste or odor in the water or ice
• Decreased water flow to the dispenser or ice maker
• Visible particulate matter in the water or ice cubes

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This is a replacement dryer complete assembly designed to restore drying function and structure for compatible Bosch laundry units. It provides the main cabinet and drum enclosure needed for normal tumbling and airflow. What it does

• Houses the drum and internal components so clothes can tumble during the drying cycle
• Provides the enclosure and mounting points for the blower, heating system, and controls
• Restores proper airflow pathways to help the dryer heat and vent as intended
• Helps eliminate issues caused by damaged or severely warped cabinet or drum housings

• One complete dryer assembly as shown

• Disconnect power before servicing
• Follow factory service manual for alignment, seal, and vent reconnection steps
• Inspect and replace any worn seals, ducts, or mounting hardware as needed during installation

This replacement top lid restores the appliance's sealed cover and appearance while protecting internal components from debris and moisture. It fits where the original top cover was damaged, cracked, or cosmetically worn. What it does:

• Replaces a cracked, warped, or broken top cover to protect internal parts
• Helps keep dust, water splashes, and debris out of the appliance interior
• Restores a secure, flush top surface and original appearance
• Reduces risk of further damage from exposed components

• Disconnect power and water (if applicable) before starting any repair
• Basic hand tools are typically required; handle edges carefully to avoid scratches
• Inspect mounting points/hinges during install; reuse or replace fasteners as needed

This replacement top lid restores the appliance's sealed cover and appearance while protecting internal components from debris and moisture. It fits where the original top cover was damaged, cracked, or cosmetically worn. What it does:

• Replaces a cracked, warped, or broken top cover to protect internal parts
• Helps keep dust, water splashes, and debris out of the appliance interior
• Restores a secure, flush top surface and original appearance
• Reduces risk of further damage from exposed components

• Disconnect power and water (if applicable) before starting any repair
• Basic hand tools are typically required; handle edges carefully to avoid scratches
• Inspect mounting points/hinges during install; reuse or replace fasteners as needed

The Water Filter is an OEM part for Bosch refrigerators. This part removes impurities and contaminants from the water supply to your appliance. This part ensures that the water and ice dispensed by your refrigerator are clean, taste fresh, and are free of common waterborne particles and substances. 

Over time, the water filter can become clogged with sediments and contaminants, reducing its effectiveness and potentially affecting the taste and quality of the water and ice. Regular replacement is essential for maintaining optimal performance.

Symptoms of a bad Water Filter include:

• Unpleasant taste or odor in the water or ice
• Decreased water flow to the dispenser or ice maker
• Visible particulate matter in the water or ice cubes

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This power module is the appliance control board that regulates electrical power to key functions, helping restore reliable operation when the original board is faulty. It replaces the main power/control electronics assembly. What it does

• Controls and distributes electrical power to the appliance's control circuits and motors.
• Helps prevent erratic operation when the original power electronics fail.
• Commonly replaced to address intermittent power loss, no-start symptoms, or unresponsive controls.
• Works as the main interface between incoming power and the appliance's control system.

• One power module/control board.

• Disconnect power before removing or installing this part to avoid shock.
• Handle the circuit board by its edges and avoid touching components to prevent ESD damage.
• Some models require panels removed and mounting screws detached; retain hardware for reassembly.

A replacement housing cover that protects internal components and helps keep the appliance sealed from debris and moisture. Replaces a worn or damaged cover to restore proper component protection and fit. What it does

• Shields internal motor, pump, or electrical components from debris and moisture.
• Helps maintain proper routing and positioning of nearby parts and wiring.
• Can prevent rubbing or contact-related noise caused by a cracked or loose cover.
• Common symptom: visible cracks, breaks, or a loose cover after impact or wear.

• One cover housing as shown.

• Disconnect power and water before starting any repair.
• Remove access panels or components only as needed to reach the cover; keep track of fasteners.
• Inspect surrounding seals, gaskets, and mounting tabs for damage and replace if necessary.

A replacement shock absorber that cushions and appliance component to reduce noise and stabilize movement for smoother, more controlled operation. Restores dampening to doors or tubs that close unevenly or vibrate. What it does:

• Dampens and slows movement to prevent slamming and reduce impact wear
• Stabilizes panels or tubs to cut down on vibration and rattling sounds
• Helps maintain even, controlled closing and opening motion
• Commonly used when a door feels loose, drops, or closes too quickly

• Disconnect power (and water if applicable) before attempting service
• Retain original mounting hardware; only replace items explicitly listed as included
• Ensure correct orientation and secure fasteners; test operation after installation

This foot installs at the appliance base to support and level the unit. Replacing a worn or missing foot restores stability, reduces vibration and rattling, and makes accurate leveling easier.

• Provides a stable contact point between the appliance and the floor
• Allows height adjustment during leveling
• A damaged or missing foot can cause wobbling, uneven operation, vibration, or noise
• Common signs include cracking, deformation, or a loose/stripped attachment

• Disconnect power and shut off any utilities before servicing
• Carefully tip or raise the appliance to access the base; use a helper and proper supports
• Install the new foot and adjust height to level the unit
• Verify stability front-to-back and side-to-side after re-leveling

The Relay-Starting is an OEM part for Bosch refrigerators. It is responsible for controlling the start signal to initiate proper refrigeration.

The relay-starting facilitates smooth and reliable cooling performance by properly communicating the start command to the compressor. This allows the refrigeration system to kick on as needed to maintain the set interior temperature.

Causes of a faulty relay-starting include normal wear over time or failures in the electronic components themselves.

Symptoms of a bad relay-starting include:

• The refrigerator failing to cool properly
• Fluctuations in interior temperatures
• Strange humming or buzzing sounds from inside the appliance
• The cooling system not activating as expected

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This rack wheel lets your dishwasher rack glide smoothly along its rails. Replacing a worn, cracked, or missing wheel restores easy in-and-out movement and helps keep the rack properly supported during loading and unloading.

• Mounts to the rack/rail to support and guide the rack
• Allows the rack to roll smoothly on the track
• Helps prevent sticking, wobbling, or the rack jumping off the track
• Common symptoms: hard-to-slide rack, wheel damage, or rack derailing

• Unplug the dishwasher. Turn off water supply.
• Pull the rack out; release the old wheel from its clip/fastener.
• Attach the new wheel in the same position and ensure it spins freely.
• Reinstall the rack and test for smooth travel.

A replacement water inlet valve assembly that controls water entry to the appliance for proper fill cycles and normal operation. Restores reliable filling and helps stop unwanted leaks or no-fill conditions. What it does

• Opens and closes to let water into the unit during fill cycles.
• Helps maintain correct water level for washing and rinsing.
• Can stop water flow when the cycle is finished or if a fault is detected.
• Commonly associated with symptoms such as no water fill, slow fill, unit not starting due to low water, or visible leaks at the valve.

• Disconnect power and shut off the water supply before starting any repair.
• Handle electrical connections and hose fittings carefully; replace any damaged clamps or seals.

This cable connector is a replacement wire terminal used to restore a secure electrical connection in compatible Bosch appliances. It helps reestablish reliable power or signal continuity where a damaged or corroded connector causes intermittent or failed operation. What it does:

• Provides a secure electrical connection between wiring and appliance components
• Replaces damaged, corroded, or loose terminals that cause intermittent power or errors
• Helps prevent arcing and poor contact that can lead to component failure
• Suitable for repairs where the original connector is worn or physically broken

• Disconnect power before starting any repair to avoid shock or equipment damage
• Compare the replacement connector to the original for correct fit and orientation
• Use proper crimping or terminal tools if required; ensure a snug, strain-relieved connection

The Water Filter Cap is an OEM part for Bosch refrigerators. This secures the water filter within the refrigerator, ensuring a snug and leak-free fit. 

The need for a replacement can arise if the original cap is lost during a filter change, damaged, or wears out over time. 

Symptoms of a missing or damaged Water Filter Cap include:

• Difficulty in installing or securing the water filter properly, which could lead to water leaks inside the refrigerator.
• Contaminants or particles in the dispensed water, indicating that the filter is not fully sealed and thus not effectively filtering the water.
• The water filter becoming loose or falling out, compromising the refrigerator's ability to provide clean, filtered water.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Housing is an OEM part for Bosch refrigerator and freezers. This part encases the water filter, ensuring it is securely positioned within the appliance to effectively filter out contaminants from the water supply. 

The need for replacing the Housing can arise from physical damage, such as cracks or breaks, which can occur from accidental impacts during filter changes or general wear and tear over time. 

Symptoms of a compromised Housing include:

• Leaks or dripping water near the filter area, indicating that the housing may be cracked or not sealing properly.
• Difficulty in installing or removing the water filter, which could suggest that the housing is damaged or warped.
• Unfiltered water taste or odor, hinting at an improperly seated filter due to a faulty housing.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This condenser fan circulates air across the condenser coil to help remove heat from the refrigerator, improving cooling efficiency and preventing compressor overheating. It replaces a worn or damaged condenser blower assembly. What it does:

• Moves air over the condenser coil to dissipate heat from the refrigeration system
• Restores proper condenser airflow when the original fan is seized, noisy, or not spinning
• Helps prevent excessive compressor run time and warm cabinet temperatures caused by poor condenser cooling
• Rubber mounts reduce vibration and noise transfer to the cabinet

• One condenser fan assembly with rubber mounting grommets

• Disconnect power to the appliance before starting and follow all safety precautions
• Access often requires removing the rear lower service panel or toe-kick; keep track of fasteners
• Handle the fan blade and motor carefully to avoid bending blades or damaging the shaft
• After installation, verify unobstructed blade rotation and test the unit for normal operation

This shock absorber cushions and controls dishwasher door movement to reduce slamming and improve closing action. It helps protect the door and cabinet from impact and can reduce noise during operation. What it does:

• Dampens and slows the dishwasher door as it opens and closes
• Helps prevent sudden drops or slamming that can damage the door or hinges
• Reduces vibration and noise caused by uncontrolled door movement
• Restores smoother, more controlled door operation when the original shock wears out

• One shock absorber

• Disconnect power to the appliance before beginning any repair
• Remove the dishwasher door panels or access panels to reach the mounting points
• Support the door during removal/installation to prevent it from falling or binding
• Use the OEM mounting hardware and verify secure attachment and correct alignment after installation

This electronic control board is the dishwasher's primary control module that manages cycles, buttons, and displays so your appliance responds correctly to commands. Replaces a failed or faulty main control assembly to restore normal operation. What it does:

• Receives input from the user interface and starts, stops, or advances wash cycles
• Controls wash timing, pump, and valve signals to coordinate dishwasher functions
• Helps manage display lights and error reporting for diagnostic feedback
• Commonly replaced for unresponsive controls, no-start conditions, or intermittent/erratic operation

• Disconnect all power to the appliance before starting work to avoid shock or damage
• Handle the PCB carefully and avoid contact with components; protect against electrostatic discharge
• Note connector locations and wiring; reconnect all harnesses securely before testing
• Reassemble panels and verify normal operation before finishing the repair

This adhesive tape is a narrow mounting and sealing strip used to secure trim, wiring, or small components and to help reduce rattles and moisture intrusion. It provides a simple replacement for worn or missing adhesive strips. What it does:

• Secures lightweight trim pieces, wire harnesses, and small components in place
• Helps reduce vibration noise and movement of parts
• Provides a basic moisture-resistant seal on smooth, clean surfaces
• Restores adhesive grip where original tape has failed or peeled

• One adhesive tape piece as shown

• Clean and dry surfaces thoroughly before applying for best adhesion
• Press tape firmly along its entire length; allow time to set before stressing
• Replace any tape that is degraded, contaminated, or losing adhesion
• Wear gloves if needed; avoid contact with skin and keep out of reach of children

Electronic power module for the dishwasher. This is the main control board that manages power and timing for wash, drain, and drying functions, helping restore normal operation when the original module has failed or is intermittent.

• Regulates incoming power and switches major loads (circulation pump, drain pump, heater, inlet valve)
• Coordinates cycle logic based on door and sensor inputs
• May help when the dishwasher won't power on or start a cycle
• May help when cycles stop mid-way, don't complete, or drying performance is poor

• Disconnect electrical power at the circuit breaker before servicing
• Access is typically from behind the lower toe panel/base; remove panels as needed
• Photograph and label wiring; transfer any mounting hardware; seat connectors fully
• Use ESD protection and handle the board by its edges only

This electronic control module manages the appliance's cycle timing and user interface so the unit runs the selected programs correctly. Replacing a failed control restores command and timing functions. What it does

• Receives input from the control panel and starts, stops, or advances cycles
• Manages timing, relays, and sensor signals needed for normal operation
• Common symptom: appliance won't start or respond to controls
• Common symptom: display is blank, shows error codes, or cycles do not advance
• Common symptom: buttons or touchpad are unresponsive or commands are ignored

• Disconnect power to the appliance before servicing to avoid shock or damage
• Handle the board by the edges and avoid touching components or connectors
• Verify the part number on your existing module matches before installing