Parts for Ge GTH20JBBARSS: 03 - Freezer Section Parts

Replacement 8-18 x 9/16 machine screw for securing panels, brackets, and internal components. Needed when fasteners are stripped, missing, or worn.

Mounting screw for freezer interior components and panels. Replace if stripped, corroded, or missing to secure shelves, racks, or trim properly.

Replace your refrigerator's ice bin tray when cracked, broken, or missing. This tray sits in the freezer compartment to collect and store ice cubes.

Replacement plug cover and gasket assembly for refrigerator electrical access areas. Restores secure fit when original is cracked, broken, or missing.

The Light Socket is an OEM part for GE refrigerators. It is responsible for holding the refrigerator's light bulb and ensuring it receives power to illuminate the interior when the door is opened.

You should replace the light socket if it becomes faulty. Causes of a bad light socket can include wear and tear from regular use, electrical issues such as short circuits or power surges, and corrosion from moisture exposure.

Symptoms of a bad light socket include:

• The refrigerator light not turning on when the door is opened
• Flickering or intermittent light operation
• Visible damage or corrosion on the socket
• The light bulb not fitting securely or falling out

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

This silicon controlled rectifier (SCR) is an electrical control component used to regulate power in appliance circuits, helping control heating and motor circuits for reliable operation. What it does:

• Acts as a semiconductor switch to control current flow in a circuit
• Enables precise switching of power to heating elements or motors
• Can prevent uncontrolled power delivery when functioning correctly
• Faulty SCRs may cause intermittent operation, no power to a circuit, or erratic heating/motor behavior

• Disconnect all power before servicing; risk of shock or damage
• Handle as an electrostatic-sensitive device; avoid touching leads or terminals directly
• Verify mounting orientation and secure all connections per appliance wiring diagrams

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Fix a refrigerator that's not cooling properly with a new evaporator fan motor. This part circulates cold air throughout the fridge compartments.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.

Fix a warm fridge or freezer ice buildup. This defrost heater melts frost on evaporator coils to restore cooling. Moderate DIY repair, 1-2 hours.

This replacement defrost heater warms the freezer's evaporator area during the automatic defrost cycle. It melts accumulated frost so air can circulate, helping maintain stable temperatures and preventing ice buildup on the back wall.

• Heats the evaporator to clear frost and ice during defrost
• Helps keep airflow passages and the defrost drain path open
• Common symptoms of a failed heater: heavy frost on the back panel/coils, poor cooling or warm sections, fan noise from ice contact, cooling returns temporarily after a manual defrost
• Typically located behind the rear freezer panel

• Disconnect power before servicing; wear cut-resistant gloves
• Access the evaporator by removing the freezer's rear panel; thaw heavy ice before removal
• Transfer any clips/brackets and route wires exactly as original, keeping them away from plastic parts
• After installation, ensure wiring connections are secure and the heater is not contacting plastic surfaces

This holder element assembly secures the appliance's heating element in the correct position so the element stays stable for consistent operation and safe performance. It's a direct-fit replacement for worn or damaged holders. What it does:

• Secures and supports the heating element inside the appliance to maintain proper alignment
• Prevents element sagging or contact with other components that can cause noise or arcing
• Helps reduce vibration and movement that can lead to intermittent heating
• Common symptom: visible holder damage, loose or shifted element, unusual noise during operation

• Disconnect power (unplug or switch off breaker) before starting any repair
• Allow appliance and element to fully cool before handling
• Handle the element and holder carefully to avoid bending or damaging the element

Routes defrost water from the evaporator to the drain system. Replace this trough if cracked, clogged, or damaged to prevent water pooling inside your fridge.

Secures evaporator thermistor to tubing for accurate temperature readings. Replace if broken or missing to restore proper cooling and defrost cycles. Confirm fit.

8-18 CA HX 1/2 S

Secures the evaporator fan assembly to the freezer compartment wall. Replace this mounting bracket if cracked, broken, or missing hardware slots.

Secures water tubing to fittings in refrigerators and dishwashers. Replace if leaking, tubing slips off, or clamp is cracked. Confirm fit with model number.