Parts for Ge PFSF0MFZBBB: 02 - Freezer Section Parts

Purifies water before reaching your dispenser and ice maker. Replace every 6 months for clean, safe drinking water. Verify fit with your model number.

Mounting screw secures door handles to refrigerator doors. Replace if missing, stripped, or broken. Requires allen wrench for installation. Essential hardware.

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

This self-adhesive foam strip replaces worn or missing foam used to seal gaps and reduce vibration in refrigerators and freezers. It helps improve insulation and quiet operation by filling small openings where air or moisture can pass. What it does:

• Provides a compressible seal to reduce air leaks that can cause frost buildup or uneven cooling
• Dampens vibration and rattling between panels or trim pieces
• Helps block dust and moisture from entering cabinet seams
• Can restore proper door and panel contact where original foam has deteriorated

• Unplug the appliance before starting any repair
• Clean and dry the mounting surface; remove backing and press strip firmly in place
• Trim to fit with scissors or utility knife as needed; avoid stretching the foam
• Only replace foam where original is missing or damaged; follow OEM placement for best seal

Self-adhesive foam strip seals gaps along doors and panels to reduce air leaks and vibration. Replace when worn or compressed to restore efficiency.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.

Secures water tubing to fittings in refrigerators and dishwashers. Replace if leaking, tubing slips off, or clamp is cracked. Confirm fit with model number.

Protective insulation sleeve for refrigerator wiring harnesses. Installs around electrical wiring to prevent heat damage and wear. Replace if cracked or torn.

Mounting screw for refrigerator and freezer internal components. Replace if stripped, missing, or damaged during repairs. Secures panels and parts.

Fix inconsistent temps or ice buildup on evaporator coils? This sensor seal protects accuracy. DIY-friendly with wire splicing. Video guide available.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

Interior light not working when door opens? This light switch controls refrigerator illumination. DIY-friendly install takes 30-45 minutes with video.

Illuminates your refrigerator interior. Replace when burned out or flickering. Appliance-rated for durability. Verify wattage and base type match.

Refrigerator light not working or flickering? A faulty light socket often causes this. Simple plug-in repair with no tools required. Video guide available.

Hex head screw for securing interior panels, control covers, and components inside your refrigerator. Replace missing, stripped, or damaged screws.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

Wire tie retainer for refrigerators. Secures and organizes internal wiring. Replace if cracked, broken, or missing to keep wires properly bundled.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.

Secures the evaporator fan assembly to the freezer compartment wall. Replace this mounting bracket if cracked, broken, or missing hardware slots.

Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.

Mounting screw for freezer interior components and panels. Replace if stripped, corroded, or missing to secure shelves, racks, or trim properly.

Fix a warm fridge or freezer ice buildup. This defrost heater melts frost on evaporator coils to restore cooling. Moderate DIY repair, 1-2 hours.

Ice maker not filling or water spilling? This fill cup directs water into the ice maker mold for proper ice production. Simple clip-on install.

Freezer coils icing up and fridge too warm? This defrost thermostat monitors evaporator temperature to prevent overheating. Easy 20-minute DIY fix.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Fridge warm but freezer cold? Your evaporator fan motor likely failed. Fixes air circulation issues. Moderate DIY repair with basic tools.

Rubber bumper that cushions and mounts the evaporator fan motor assembly. Replace if cracked, deteriorated, or missing to reduce vibration and noise.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.